Linksys BEPSR31 Configure the Router, Advanced Proxies. Click Direct Connection to the Internet

Page 25

Instant Broadband™ Series

Chapter 8: Configure the Router

This chapter will show you how to configure the Router to function in your net- work and gain access to the Internet through your Internet Service Provider (ISP). Detailed description of the Router’s Web-based Utility can be found in “Chapter 9: The Cable/DSL Router’s Web-based Utility.” Your ISP may require the use of a Host Name and Domain Name. Further, you will set the WAN Connection Type on the Router’s Setup tab based on the information provided by your ISP. You will need the setup information from your ISP. If you do not have this information, please contact your ISP before proceeding.

The instructions from your ISP tell you how to set up your PC for Internet access. Because you are now using the Router to share Internet access among several computers, you will use the setup information to configure the Router instead of your PC. You only need to configure the Router once using the first computer you set up.

1.Open your web browser. (It is all right if you get an error message at this point. Continue following these directions.) Enter http://192.168.1.1 in the web browser’s Address field,

as shown in Figure 8-1, and press the Enter key.

Figure 8-1

2.An Enter Network Password window, shown in Figure 8-2, will appear (Windows XP users will see a Connect to 192.168.1.1 window, shown in Figure 8-3). Leave the User Name field empty, and enter admin in lower- case letters in the Password field (admin is the default password). Then, click the OK button.

Figure 8-2

Figure 8-3

EtherFast® Cable/DSL Routers

3.The Router configuration screen will appear with the Setup tab selected. Based on the setup instructions from your ISP, you may need to provide the following information.

Host Name and Domain Name: These fields allow you to provide a host name and domain name for the Router. These fields are usually left blank. If requested by your ISP (usually cable ISPs), complete these two fields.

Device IP Address and Subnet Mask: The values for the Router’s IP Address and Subnet Mask are shown on the Setup screen. The default value is 192.168.1.1 for the IP Address and 255.255.255.0 for the Subnet Mask. Leave these settings alone.

4.The Router supports five connection types: DHCP (obtain an IP automati- cally), PPPoE, Static IP Address, RAS, and PPTP. These types are listed in the drop-down menu for the WAN Connection Type setting. Each Setup screen and available features will differ depending on what kind of connec- tion type you select. Proceed to the instructions for the connection type you are using. When you are finished with the Setup tab, proceed to step 5.

IMPORTANT: If you have previously enabled any Internet-sharing proxy server software on any of your PCs, you must disable it now.

Some examples of Internet-sharing software are Internet LanBridge, Wingate, ICS, and Sygate. To disable your Internet-sharing software:

•If you are running Netscape Navigator, click Edit >> Preferences

>>Advanced >> Proxies. Click Direct Connection to the Internet.

•If you are running Internet Explorer 5.x or higher, click Start >> Settings >> Control Panel >> Internet Options >> Connections

>>LAN Settings. Remove checkmarks from all three boxes. Click the OK button to continue.

Also, you must disable any Internet log-on software (such as Ivasion Winpoet or Enternet 300) and any firewall software (such as ZoneAlarm and Watchdog) on all of your PCs.

42

43

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Cable/DSL Routers Copyright & Trademarks Table of Contents Introduction FeaturesLinksys EtherFastCable/DSLRouterRouter PackageContentsforforthethe11--PortRouterBEFSR11 Package Contents for the 4-Port Router BEFSR41Minimum Requirements An Introduction to LANs and WANs Package Contents for the 3-Port Router BEFSRU31IP Addresses Network Setup Overview Dhcp Dynamic Host Configuration Protocol ServersDynamic IP Addresses 4-Port Router’s Front Panel LEDs 4-Port Router’s Rear PanelReset Button Buttons & SwitchesProceed to Connect the Router 1-Port Router’s Rear PanelWAN Indicators Crossover SwitchPort 1-Port Router’s Front Panel LEDsUSB Compatibility 3-Port Router’s Rear PanelFull/Col 3-Port Router’s Front Panel LEDsConnect the Router Connecting Your Hardware Together and Booting UpOverview Uplinking Connecting More Devices to the Router Router’s hardware installation is now completeInstalling the Windows 98 Driver Installing the BEFSRU31’s USB Port DriversInstant Broadband Series Installing the Windows 2000 Driver Instant Broadband Series Installing the Windows Millennium Driver Installing the Windows XP Driver Configure the PCs Go to Configure the Router Configuring Windows 95, 98, and Millennium PCsConfiguring Windows 2000 PCs Configuring Windows XP PCs Advanced Proxies. Click Direct Connection to the Internet Configure the RouterPPPoE Dhcp or Obtain an IP Address AutomaticallyStatic IP Address or Specify an IP Address Enter the Gateway AddressCable/DSL Router’s Web-based Utility Quick and Easy Router AdministrationDhcp SetupPPPoE Pptp Status PasswordDhcp Log ZoneAlarm Pro SettingsSecurity Software DownloadOr Disable PC-cillin SettingsExempt Computers AOL Parental ControlsEditing MAC Filter Setting Setting Up FiltersIP Filtering AdvancedPort Range Forwarding UPnP Forwarding Port Triggering Static Routing Dynamic RoutingDMZ Host Common Problems and Solutions Appendix a TroubleshootingMAC Address Clone Need to set a static IP address on a PCFor Windows XP For Windows NTWant to test my Internet connection For Windows 95, 98, and MeFor Windows XP Need to set up a server behind my Router Am not able to access the Router’s web interface SetupCan’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnectingNeed to use port triggering Click the Advanced = Filter tabDiag LED stays lit continuously Full/Col LED keeps flickering continuouslyFrequently Asked Questions Allows Pptp packets to pass through Appendix B Glossary Instant Broadband Series Instant Broadband Series Instant Broadband Series 101 103 Appendix C How to Ping Your ISP’s E-mail & Web Addresses Step Two Pinging for a Web Address Step One Pinging an IP AddressTCP/IP installation is now complete Appendix D Installing the TCP/IP ProtocolCrimping Your Own Network Cables Appendix E Twisted-Pair CablingStraight-Through Cabling For Windows NT, 2000, and XP Figure F-1Figure F-5 Http//192.168.1.1 in the web AOL Broadband via CableObtain an IP automat- ically from Four 10/100 RJ-45 switched ports and shared Appendix H 4-Port Router SpecificationsPort Environmental Specifications AOL Broadband via DSLAppendix J 3-Port Router Specifications Appendix I 1-Port Router SpecificationsPort Router Specifications Three 10/100 RJ-45 Switched ports and sharedSales Information Technical Support RMA Issues Fax Appendix K Warranty InformationAppendix L Contact Information Web site FTP siteCopyright 2002 Linksys, All Rights Reserved
Top Page Image Contents