Linksys BEPSR41, BEPSR31 manual Step One Pinging an IP Address, Step Two Pinging for a Web Address

Page 57

Instant Broadband™ Series

Step One: Pinging an IP Address

The first step to determining your ISP’s web and e-mail server address is to ping its IP address.

1.Power on the computer and the cable or DSL modem, and restore the network configuration set by your ISP if you have since changed it.

2.Click Start, then Run, and type command. This will bring up the DOS window.

3.At the DOS command prompt, type ping mail (assuming that the loca- tion for which you’re trying to find an IP address is configured as mail). Press Enter. Information such as the following data, taken from a ping of Microsoft Network’s e-mail server, will be displayed.

C:\>ping mail

Pinging mail [24.53.32.4] with 32 bytes of data:

Reply from 24.53.32.4: bytes=32 time<10ms TTL=128

Reply from 24.53.32.4: bytes=32 time<10ms TTL=128

Reply from 24.53.32.4: bytes=32 time<10ms TTL=128

Reply from 24.53.32.4: bytes=32 time<10ms TTL=128

Ping statistics for 24.53.32.4:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms

Figure C-1

4.Write down the IP address returned by the ping command. (In the example above: 24.53.32.4.) This IP address is the actual IP address of the server mail, or any other word or value you have pinged.

EtherFast® Cable/DSL Routers

Step Two: Pinging for a Web Address

While the IP address returned above would work as your e-mail server address, it may not be permanent. IP addresses change all the time. Web addresses, how- ever, usually don’t. Because of this, you’re likely to have fewer problems by configuring your system with web addresses rather than IP addresses. Follow the instructions below to find the web address assigned to the IP address you just pinged.

1.At the DOS command prompt, type ping -a 24.53.32.4, where 24.53.32.4 is the IP address you just pinged. Information such as the following data

will be displayed. C:\>ping -a 24.53.32.4

Pinging mail.msnv3.occa.home.com [24.53.32.4] with

32 bytes of data:

Reply from 24.53.32.4: bytes=32 time<10ms TTL=127

Reply from 24.53.32.4: bytes=32 time<10ms TTL=127

Reply from 24.53.32.4: bytes=32 time<10ms TTL=127

Reply from 24.53.32.4: bytes=32 time<10ms TTL=127

Ping statistics for 24.53.32.4:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms

Figure C-2

2.Write down the web address returned by the ping command (In the example in Figure C-2:mail.msnv3.occa.home.com is the web address). This web address is the web address assigned to the IP address you just pinged. While the IP address of mail could conceivably change, it is likely that this web address will not.

3.Replace your ISP’s abbreviated server address with this extended web address in the corresponding Internet application (web browser, e-mail application, etc.).

Once you have replaced the brief server address with the true server address, the Router should have no problem accessing the Internet through that Internet application.

106

107

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Cable/DSL Routers Copyright & Trademarks Table of Contents Features IntroductionLinksys EtherFastCable/DSLRouterRouter Package Contents for the 4-Port Router BEFSR41 PackageContentsforforthethe11--PortRouterBEFSR11Minimum Requirements Package Contents for the 3-Port Router BEFSRU31 An Introduction to LANs and WANsIP Addresses Dhcp Dynamic Host Configuration Protocol Servers Network Setup OverviewDynamic IP Addresses 4-Port Router’s Front Panel LEDs 4-Port Router’s Rear PanelReset Button Buttons & SwitchesProceed to Connect the Router 1-Port Router’s Rear PanelWAN Indicators Crossover SwitchPort 1-Port Router’s Front Panel LEDsUSB Compatibility 3-Port Router’s Rear PanelFull/Col 3-Port Router’s Front Panel LEDsConnecting Your Hardware Together and Booting Up Connect the RouterOverview Uplinking Connecting More Devices to the Router Router’s hardware installation is now completeInstalling the Windows 98 Driver Installing the BEFSRU31’s USB Port DriversInstant Broadband Series Installing the Windows 2000 Driver Instant Broadband Series Installing the Windows Millennium Driver Installing the Windows XP Driver Configure the PCs Go to Configure the Router Configuring Windows 95, 98, and Millennium PCsConfiguring Windows 2000 PCs Configuring Windows XP PCs Advanced Proxies. Click Direct Connection to the Internet Configure the RouterPPPoE Dhcp or Obtain an IP Address AutomaticallyStatic IP Address or Specify an IP Address Enter the Gateway AddressCable/DSL Router’s Web-based Utility Quick and Easy Router AdministrationDhcp SetupPPPoE Pptp Status PasswordDhcp Log ZoneAlarm Pro SettingsSecurity Software DownloadOr Disable PC-cillin SettingsExempt Computers AOL Parental ControlsEditing MAC Filter Setting Setting Up FiltersIP Filtering AdvancedPort Range Forwarding UPnP Forwarding Port Triggering Static Routing Dynamic RoutingDMZ Host Common Problems and Solutions Appendix a TroubleshootingMAC Address Clone Need to set a static IP address on a PCFor Windows XP For Windows NTWant to test my Internet connection For Windows 95, 98, and MeFor Windows XP Need to set up a server behind my Router Am not able to access the Router’s web interface SetupCan’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnectingNeed to use port triggering Click the Advanced = Filter tabDiag LED stays lit continuously Full/Col LED keeps flickering continuouslyFrequently Asked Questions Allows Pptp packets to pass through Appendix B Glossary Instant Broadband Series Instant Broadband Series Instant Broadband Series 101 103 Appendix C How to Ping Your ISP’s E-mail & Web Addresses Step Two Pinging for a Web Address Step One Pinging an IP AddressTCP/IP installation is now complete Appendix D Installing the TCP/IP ProtocolAppendix E Twisted-Pair Cabling Crimping Your Own Network CablesStraight-Through Cabling For Windows NT, 2000, and XP Figure F-1Figure F-5 AOL Broadband via Cable Http//192.168.1.1 in the webObtain an IP automat- ically from Four 10/100 RJ-45 switched ports and shared Appendix H 4-Port Router SpecificationsPort Environmental Specifications AOL Broadband via DSLAppendix J 3-Port Router Specifications Appendix I 1-Port Router SpecificationsPort Router Specifications Three 10/100 RJ-45 Switched ports and sharedSales Information Technical Support RMA Issues Fax Appendix K Warranty InformationAppendix L Contact Information Web site FTP siteCopyright 2002 Linksys, All Rights Reserved

BEPSR31, BEPSR11, BEPSR41 specifications

The Linksys BEPSR series, which includes the BEPSR41, BEPSR11, and BEPSR31 models, is renowned for its commitment to providing robust, reliable networking solutions for both home and small office environments. Each model in this line features distinctive characteristics that suit different needs while maintaining the core performance that Linksys is known for.

The Linksys BEPSR41 is a four-port broadband router that stands out for its exceptional speed and stability. With support for ADSL and cable connections, this model is equipped with advanced features such as Network Address Translation (NAT) and a built-in firewall for enhanced security. The BEPSR41 utilizes wired Ethernet technology, providing reliable connections and lag-free access to the internet. Its four LAN ports enable connections to multiple devices, making it an ideal choice for households with numerous connected devices.

Moving on to the Linksys BEPSR11, this model is a more compact solution, designed for users with simpler networking needs. The BEPSR11 features a one-port configuration, making it perfect for individual users or small setups that require minimal device connectivity. Despite its smaller size, it offers solid performance with similar NAT and firewall capabilities as its larger counterpart. This model is an excellent choice for users who value simplicity and efficient internet connectivity without the complexities of advanced networking setups.

Lastly, the Linksys BEPSR31 combines features from both previous models, offering an ideal balance between performance and usability. It provides two LAN ports, making it suitable for small offices or homes where a couple of wired connections are needed. The setup process is straightforward, allowing users to get online quickly with minimal configuration. The BEPSR31 also supports basic QoS (Quality of Service) features, allowing users to prioritize traffic for smoother streaming and gaming experiences.

All three models emphasize ease of use, security, and dependable performance, catering to different user requirements. Their solid design, combined with Linksys’s reputation for quality and reliability in home networking, makes the BEPSR41, BEPSR11, and BEPSR31 excellent options for anyone looking to enhance their internet experience without extensive technical knowledge. Whether for gaming, streaming, or everyday browsing, these routers provide essential features that meet modern connectivity demands.
Top Page Image Contents