Linksys BEPSR11, BEPSR41, BEPSR31 manual Port Router’s Rear Panel, Port Router’s Front Panel LEDs

Page 8

Instant Broadband™ Series

Chapter 2: Getting to Know the 4- Port EtherFast® Cable/DSL Router

The 4-Port Router’s Rear Panel

The Router’s ports, where network cables are connected, are located on the rear panel of the Router, as shown in Figure 2-1.

 

Figure 2-1

WAN

The WAN (Wide Area Network) port is where you

 

connect your cable or DSL modem through an

 

Ethernet cable. Your modem connection will not

 

work from any other port.

Ports 1-4

These four LAN (Local Area Network) ports con-

 

nect to network devices, such as PCs, print servers,

 

and remote hard drives. If Port 1 is being used, the

 

Uplink port will not work because these two shared

 

ports have internally shared wiring.

Uplink

The Uplink port is used to expand your network by

 

connecting to another switch or hub. To uplink to a

 

switch or a hub, simply run a cable from the Uplink

 

port to the other device. See the “Uplinking:

 

Connecting More Devices to the Router” section for

 

more on uplinking.

 

If the Uplink port is being used, Port 1 will not

 

work.

Power

The Power port is where you will connect the

 

power adapter.

EtherFast® Cable/DSL Routers

The 4-Port Router’s Front Panel LEDs

 

Figure 2-2

Power

Green. The Power LED lights up when the Router is powered

 

on.

Link/Act

Green. The Link/Act LED serves two purposes. If the LED

 

is continuously lit, the Router is successfully connected to a

 

device through the corresponding port (1, 2, 3 or 4). If the

 

LED is flickering, the Router is actively sending or receiving

 

data over that port. Port 1 is lit when using the Uplink port.

Full/Col

Green. The Full/Col LED also serves two purposes. If this

 

LED is lit up continuously, the connection made through the

 

corresponding port is running in Full Duplex mode. If the

 

LED flickers, the connection is experiencing collisions.

 

Infrequent collisions are normal.

 

If this LED flickers too often, there may be a problem with

 

your connection. See “Appendix A: Troubleshooting” if you

 

encounter this problem.

100Orange. The 100 LED lights up when a successful 100Mbps connection is made through the corresponding port.

If this LED does not light up, then your connection speed is 10 Mbps.

8

9

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Cable/DSL Routers Copyright & Trademarks Table of Contents Linksys EtherFastCable/DSLRouterRouter FeaturesIntroduction Minimum Requirements Package Contents for the 4-Port Router BEFSR41PackageContentsforforthethe11--PortRouterBEFSR11 IP Addresses Package Contents for the 3-Port Router BEFSRU31An Introduction to LANs and WANs Dynamic IP Addresses Dhcp Dynamic Host Configuration Protocol ServersNetwork Setup Overview 4-Port Router’s Rear Panel 4-Port Router’s Front Panel LEDsButtons & Switches Reset ButtonProceed to Connect the Router 1-Port Router’s Rear PanelCrossover Switch WAN IndicatorsPort 1-Port Router’s Front Panel LEDs3-Port Router’s Rear Panel USB Compatibility3-Port Router’s Front Panel LEDs Full/ColOverview Connecting Your Hardware Together and Booting UpConnect the Router Router’s hardware installation is now complete Uplinking Connecting More Devices to the RouterInstalling the BEFSRU31’s USB Port Drivers Installing the Windows 98 DriverInstant Broadband Series Installing the Windows 2000 Driver Instant Broadband Series Installing the Windows Millennium Driver Installing the Windows XP Driver Configure the PCs Configuring Windows 95, 98, and Millennium PCs Go to Configure the RouterConfiguring Windows 2000 PCs Configuring Windows XP PCs Configure the Router Advanced Proxies. Click Direct Connection to the InternetDhcp or Obtain an IP Address Automatically PPPoEStatic IP Address or Specify an IP Address Enter the Gateway AddressQuick and Easy Router Administration Cable/DSL Router’s Web-based UtilitySetup DhcpPPPoE Pptp Password StatusDhcp ZoneAlarm Pro Settings LogSecurity Software DownloadPC-cillin Settings Or DisableExempt Computers AOL Parental ControlsSetting Up Filters Editing MAC Filter SettingIP Filtering AdvancedPort Range Forwarding UPnP Forwarding Port Triggering Dynamic Routing Static RoutingDMZ Host Appendix a Troubleshooting Common Problems and SolutionsMAC Address Clone Need to set a static IP address on a PCFor Windows NT For Windows XPWant to test my Internet connection For Windows 95, 98, and MeFor Windows XP Am not able to access the Router’s web interface Setup Need to set up a server behind my RouterCan’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnectingClick the Advanced = Filter tab Need to use port triggeringDiag LED stays lit continuously Full/Col LED keeps flickering continuouslyFrequently Asked Questions Allows Pptp packets to pass through Appendix B Glossary Instant Broadband Series Instant Broadband Series Instant Broadband Series 101 103 Appendix C How to Ping Your ISP’s E-mail & Web Addresses Step One Pinging an IP Address Step Two Pinging for a Web AddressAppendix D Installing the TCP/IP Protocol TCP/IP installation is now completeStraight-Through Cabling Appendix E Twisted-Pair CablingCrimping Your Own Network Cables Figure F-1 For Windows NT, 2000, and XPFigure F-5 Obtain an IP automat- ically from AOL Broadband via CableHttp//192.168.1.1 in the web Appendix H 4-Port Router Specifications Four 10/100 RJ-45 switched ports and sharedPort Environmental Specifications AOL Broadband via DSLAppendix I 1-Port Router Specifications Appendix J 3-Port Router SpecificationsPort Router Specifications Three 10/100 RJ-45 Switched ports and sharedAppendix K Warranty Information Sales Information Technical Support RMA Issues FaxAppendix L Contact Information Web site FTP siteCopyright 2002 Linksys, All Rights Reserved

BEPSR31, BEPSR11, BEPSR41 specifications

The Linksys BEPSR series, which includes the BEPSR41, BEPSR11, and BEPSR31 models, is renowned for its commitment to providing robust, reliable networking solutions for both home and small office environments. Each model in this line features distinctive characteristics that suit different needs while maintaining the core performance that Linksys is known for.

The Linksys BEPSR41 is a four-port broadband router that stands out for its exceptional speed and stability. With support for ADSL and cable connections, this model is equipped with advanced features such as Network Address Translation (NAT) and a built-in firewall for enhanced security. The BEPSR41 utilizes wired Ethernet technology, providing reliable connections and lag-free access to the internet. Its four LAN ports enable connections to multiple devices, making it an ideal choice for households with numerous connected devices.

Moving on to the Linksys BEPSR11, this model is a more compact solution, designed for users with simpler networking needs. The BEPSR11 features a one-port configuration, making it perfect for individual users or small setups that require minimal device connectivity. Despite its smaller size, it offers solid performance with similar NAT and firewall capabilities as its larger counterpart. This model is an excellent choice for users who value simplicity and efficient internet connectivity without the complexities of advanced networking setups.

Lastly, the Linksys BEPSR31 combines features from both previous models, offering an ideal balance between performance and usability. It provides two LAN ports, making it suitable for small offices or homes where a couple of wired connections are needed. The setup process is straightforward, allowing users to get online quickly with minimal configuration. The BEPSR31 also supports basic QoS (Quality of Service) features, allowing users to prioritize traffic for smoother streaming and gaming experiences.

All three models emphasize ease of use, security, and dependable performance, catering to different user requirements. Their solid design, combined with Linksys’s reputation for quality and reliability in home networking, makes the BEPSR41, BEPSR11, and BEPSR31 excellent options for anyone looking to enhance their internet experience without extensive technical knowledge. Whether for gaming, streaming, or everyday browsing, these routers provide essential features that meet modern connectivity demands.
Top Page Image Contents