Linksys BEPSR41, BEPSR31, BEPSR11 manual Dynamic Routing, Static Routing

Page 39

Instant BroadbandSeries

Dynamic Routing

Figure 9-20

With Dynamic Routing (Figure 9-20) you can enable the Router to automati- cally adjust to physical changes in the network’s layout. The Router, using the RIP protocol, determines the network packets’ route based on the fewest num- ber of hops between the source and the destination. The RIP protocol regular- ly broadcasts routing information to other routers on the network. To set up Dynamic Routing:

1.Choose the correct Working Mode. Gateway Mode should be used if the Router is hosting your network’s connection to the Internet. Router Mode should be selected if the Router exists on a network with other routers. In Router Mode, any computer connected to the Router will not be able to connect to the Internet unless you have another router function as the Gateway.

2.Choose a Dynamic Routing path protocol for either transmission (TX:) or reception (RX:) of network data.

When finished making your changes on this tab, click the Apply button to save these changes, or click the Cancel button to undo your changes. For further help on this tab, click the Help button.

Click the Show Routing Table button to open a chart displaying how data is routed through your LAN.

EtherFast® Cable/DSL Routers

Static Routing

Figure 9-21

If the Router is connected to more than one network, it may be necessary to set up a static route between them. A static route is a pre-determined pathway that network information must travel to reach a specific host or network. From the Static Routing tab, as shown in Figure 9-21, click the Show Routing Table but- ton to view the current static routing configuration.

To create a static route entry:

1.Select a Static Route Entry from the drop-down list. The Router supports up to 20 static route entries.

To delete a Static Routing entry, select an entry, and click the Delete this entry button.

70

71

Image 39
Contents Cable/DSL Routers Copyright & Trademarks Table of Contents Features IntroductionLinksys EtherFastCable/DSLRouterRouter Package Contents for the 4-Port Router BEFSR41 PackageContentsforforthethe11--PortRouterBEFSR11Minimum Requirements Package Contents for the 3-Port Router BEFSRU31 An Introduction to LANs and WANsIP Addresses Dhcp Dynamic Host Configuration Protocol Servers Network Setup OverviewDynamic IP Addresses 4-Port Router’s Front Panel LEDs 4-Port Router’s Rear Panel1-Port Router’s Rear Panel Buttons & SwitchesReset Button Proceed to Connect the Router1-Port Router’s Front Panel LEDs Crossover SwitchWAN Indicators PortUSB Compatibility 3-Port Router’s Rear PanelFull/Col 3-Port Router’s Front Panel LEDsConnecting Your Hardware Together and Booting Up Connect the RouterOverview Uplinking Connecting More Devices to the Router Router’s hardware installation is now completeInstalling the Windows 98 Driver Installing the BEFSRU31’s USB Port DriversInstant Broadband Series Installing the Windows 2000 Driver Instant Broadband Series Installing the Windows Millennium Driver Installing the Windows XP Driver Configure the PCs Go to Configure the Router Configuring Windows 95, 98, and Millennium PCsConfiguring Windows 2000 PCs Configuring Windows XP PCs Advanced Proxies. Click Direct Connection to the Internet Configure the RouterEnter the Gateway Address Dhcp or Obtain an IP Address AutomaticallyPPPoE Static IP Address or Specify an IP AddressCable/DSL Router’s Web-based Utility Quick and Easy Router AdministrationDhcp SetupPPPoE Pptp Status PasswordDhcp Software Download ZoneAlarm Pro SettingsLog SecurityAOL Parental Controls PC-cillin SettingsOr Disable Exempt ComputersAdvanced Setting Up FiltersEditing MAC Filter Setting IP FilteringPort Range Forwarding UPnP Forwarding Port Triggering Static Routing Dynamic RoutingDMZ Host Need to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions MAC Address CloneFor Windows 95, 98, and Me For Windows NTFor Windows XP Want to test my Internet connectionFor Windows XP Need to set up a server behind my Router Am not able to access the Router’s web interface SetupCan’t get the Internet game, server, or application to work My DSL service’s PPPoE is always disconnecting To start over, I need to set the Router to factory defaultNeed to upgrade the firmware Firmware upgrade failed, and/or the Diag LED is flashingFull/Col LED keeps flickering continuously Click the Advanced = Filter tabNeed to use port triggering Diag LED stays lit continuouslyFrequently Asked Questions Allows Pptp packets to pass through Appendix B Glossary Instant Broadband Series Instant Broadband Series Instant Broadband Series 101 103 Appendix C How to Ping Your ISP’s E-mail & Web Addresses Step Two Pinging for a Web Address Step One Pinging an IP AddressTCP/IP installation is now complete Appendix D Installing the TCP/IP ProtocolAppendix E Twisted-Pair Cabling Crimping Your Own Network CablesStraight-Through Cabling For Windows NT, 2000, and XP Figure F-1Figure F-5 AOL Broadband via Cable Http//192.168.1.1 in the webObtain an IP automat- ically from AOL Broadband via DSL Appendix H 4-Port Router SpecificationsFour 10/100 RJ-45 switched ports and shared Port Environmental SpecificationsThree 10/100 RJ-45 Switched ports and shared Appendix I 1-Port Router SpecificationsAppendix J 3-Port Router Specifications Port Router SpecificationsWeb site FTP site Appendix K Warranty InformationSales Information Technical Support RMA Issues Fax Appendix L Contact InformationCopyright 2002 Linksys, All Rights Reserved

BEPSR31, BEPSR11, BEPSR41 specifications

The Linksys BEPSR series, which includes the BEPSR41, BEPSR11, and BEPSR31 models, is renowned for its commitment to providing robust, reliable networking solutions for both home and small office environments. Each model in this line features distinctive characteristics that suit different needs while maintaining the core performance that Linksys is known for.

The Linksys BEPSR41 is a four-port broadband router that stands out for its exceptional speed and stability. With support for ADSL and cable connections, this model is equipped with advanced features such as Network Address Translation (NAT) and a built-in firewall for enhanced security. The BEPSR41 utilizes wired Ethernet technology, providing reliable connections and lag-free access to the internet. Its four LAN ports enable connections to multiple devices, making it an ideal choice for households with numerous connected devices.

Moving on to the Linksys BEPSR11, this model is a more compact solution, designed for users with simpler networking needs. The BEPSR11 features a one-port configuration, making it perfect for individual users or small setups that require minimal device connectivity. Despite its smaller size, it offers solid performance with similar NAT and firewall capabilities as its larger counterpart. This model is an excellent choice for users who value simplicity and efficient internet connectivity without the complexities of advanced networking setups.

Lastly, the Linksys BEPSR31 combines features from both previous models, offering an ideal balance between performance and usability. It provides two LAN ports, making it suitable for small offices or homes where a couple of wired connections are needed. The setup process is straightforward, allowing users to get online quickly with minimal configuration. The BEPSR31 also supports basic QoS (Quality of Service) features, allowing users to prioritize traffic for smoother streaming and gaming experiences.

All three models emphasize ease of use, security, and dependable performance, catering to different user requirements. Their solid design, combined with Linksys’s reputation for quality and reliability in home networking, makes the BEPSR41, BEPSR11, and BEPSR31 excellent options for anyone looking to enhance their internet experience without extensive technical knowledge. Whether for gaming, streaming, or everyday browsing, these routers provide essential features that meet modern connectivity demands.