Linksys BEPSR31, BEPSR41, BEPSR11 manual To start over, I need to set the Router to factory default

Page 46

Instant Broadband™ Series

10.I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop- up window.

If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for the Internet connection, the computer does not need any proxy settings to gain access. Please follow these directions to verify that you do not have any proxy settings and that the browser you use is set to connect directly to the LAN.

For Microsoft Internet Explorer 5.0 or higher:

A.Click Start, Settings, and Control Panel. Double-clickInternet Options.

B.Click the Connections tab.

C.Click the LAN settings button and remove anything that is checked.

D.Click the OK button to go back to the previous screen.

E.Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users.

For Netscape 4.7 or higher:

A.Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies.

B.Make sure you have Direct connection to the Internet selected on this screen.

C.Close all the windows to finish.

11. To start over, I need to set the Router to factory default.

Hold the Reset button for up to 30 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings. In other words, the Router will revert to its original factory configuration.

12. I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com. Follow these steps:

A.Go to the Linksys website at http://www.linksys.com and download the latest firmware.

B.To upgrade the firmware, follow the steps in the Help section found in “Chapter 9: The Cable/DSL Router’s Web-based Utility.”

EtherFast® Cable/DSL Routers

13. The firmware upgrade failed, and/or the Diag LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Diag LED stop flashing:

A.If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

B.Set a static IP address on the PC; refer to “Problem #1, I need to set a stat- ic IP address.” Use the following IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

C.Perform the upgrade using the TFTP program or the Router’s web-based utility through its Help tab.

14. My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial- up connection to the Internet. There is a setup option to “keep alive” the con- nection. This may not always work, so you may need to re-establish connec- tion periodically.

A. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

B.Enter the password, if asked. (The default password is admin.)

C.In the Setup tab, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

D.Click the Apply button.

E.Click the Status tab, and click the Connect button.

F.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected.

G.Click the Apply button to continue.

If the connection is lost again, follow steps E to G to re-establish connection.

84

85

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Cable/DSL Routers Copyright & Trademarks Table of Contents Introduction FeaturesLinksys EtherFastCable/DSLRouterRouter PackageContentsforforthethe11--PortRouterBEFSR11 Package Contents for the 4-Port Router BEFSR41Minimum Requirements An Introduction to LANs and WANs Package Contents for the 3-Port Router BEFSRU31IP Addresses Network Setup Overview Dhcp Dynamic Host Configuration Protocol ServersDynamic IP Addresses 4-Port Router’s Rear Panel 4-Port Router’s Front Panel LEDsProceed to Connect the Router Buttons & SwitchesReset Button 1-Port Router’s Rear PanelPort Crossover SwitchWAN Indicators 1-Port Router’s Front Panel LEDs3-Port Router’s Rear Panel USB Compatibility3-Port Router’s Front Panel LEDs Full/ColConnect the Router Connecting Your Hardware Together and Booting UpOverview Router’s hardware installation is now complete Uplinking Connecting More Devices to the RouterInstalling the BEFSRU31’s USB Port Drivers Installing the Windows 98 DriverInstant Broadband Series Installing the Windows 2000 Driver Instant Broadband Series Installing the Windows Millennium Driver Installing the Windows XP Driver Configure the PCs Configuring Windows 95, 98, and Millennium PCs Go to Configure the RouterConfiguring Windows 2000 PCs Configuring Windows XP PCs Configure the Router Advanced Proxies. Click Direct Connection to the InternetStatic IP Address or Specify an IP Address Dhcp or Obtain an IP Address AutomaticallyPPPoE Enter the Gateway AddressQuick and Easy Router Administration Cable/DSL Router’s Web-based UtilitySetup DhcpPPPoE Pptp Password StatusDhcp Security ZoneAlarm Pro SettingsLog Software DownloadExempt Computers PC-cillin SettingsOr Disable AOL Parental ControlsIP Filtering Setting Up FiltersEditing MAC Filter Setting AdvancedPort Range Forwarding UPnP Forwarding Port Triggering Dynamic Routing Static RoutingDMZ Host MAC Address Clone Appendix a TroubleshootingCommon Problems and Solutions Need to set a static IP address on a PCWant to test my Internet connection For Windows NTFor Windows XP For Windows 95, 98, and MeFor Windows XP Am not able to access the Router’s web interface Setup Need to set up a server behind my RouterCan’t get the Internet game, server, or application to work Firmware upgrade failed, and/or the Diag LED is flashing To start over, I need to set the Router to factory defaultNeed to upgrade the firmware My DSL service’s PPPoE is always disconnectingDiag LED stays lit continuously Click the Advanced = Filter tabNeed to use port triggering Full/Col LED keeps flickering continuouslyFrequently Asked Questions Allows Pptp packets to pass through Appendix B Glossary Instant Broadband Series Instant Broadband Series Instant Broadband Series 101 103 Appendix C How to Ping Your ISP’s E-mail & Web Addresses Step One Pinging an IP Address Step Two Pinging for a Web AddressAppendix D Installing the TCP/IP Protocol TCP/IP installation is now completeCrimping Your Own Network Cables Appendix E Twisted-Pair CablingStraight-Through Cabling Figure F-1 For Windows NT, 2000, and XPFigure F-5 Http//192.168.1.1 in the web AOL Broadband via CableObtain an IP automat- ically from Port Environmental Specifications Appendix H 4-Port Router SpecificationsFour 10/100 RJ-45 switched ports and shared AOL Broadband via DSLPort Router Specifications Appendix I 1-Port Router SpecificationsAppendix J 3-Port Router Specifications Three 10/100 RJ-45 Switched ports and sharedAppendix L Contact Information Appendix K Warranty InformationSales Information Technical Support RMA Issues Fax Web site FTP siteCopyright 2002 Linksys, All Rights Reserved

BEPSR31, BEPSR11, BEPSR41 specifications

The Linksys BEPSR series, which includes the BEPSR41, BEPSR11, and BEPSR31 models, is renowned for its commitment to providing robust, reliable networking solutions for both home and small office environments. Each model in this line features distinctive characteristics that suit different needs while maintaining the core performance that Linksys is known for.

The Linksys BEPSR41 is a four-port broadband router that stands out for its exceptional speed and stability. With support for ADSL and cable connections, this model is equipped with advanced features such as Network Address Translation (NAT) and a built-in firewall for enhanced security. The BEPSR41 utilizes wired Ethernet technology, providing reliable connections and lag-free access to the internet. Its four LAN ports enable connections to multiple devices, making it an ideal choice for households with numerous connected devices.

Moving on to the Linksys BEPSR11, this model is a more compact solution, designed for users with simpler networking needs. The BEPSR11 features a one-port configuration, making it perfect for individual users or small setups that require minimal device connectivity. Despite its smaller size, it offers solid performance with similar NAT and firewall capabilities as its larger counterpart. This model is an excellent choice for users who value simplicity and efficient internet connectivity without the complexities of advanced networking setups.

Lastly, the Linksys BEPSR31 combines features from both previous models, offering an ideal balance between performance and usability. It provides two LAN ports, making it suitable for small offices or homes where a couple of wired connections are needed. The setup process is straightforward, allowing users to get online quickly with minimal configuration. The BEPSR31 also supports basic QoS (Quality of Service) features, allowing users to prioritize traffic for smoother streaming and gaming experiences.

All three models emphasize ease of use, security, and dependable performance, catering to different user requirements. Their solid design, combined with Linksys’s reputation for quality and reliability in home networking, makes the BEPSR41, BEPSR11, and BEPSR31 excellent options for anyone looking to enhance their internet experience without extensive technical knowledge. Whether for gaming, streaming, or everyday browsing, these routers provide essential features that meet modern connectivity demands.
Top Page Image Contents