Linksys WRTSL54GS manual Network Setup, Optional Settings, Router IP

Page 23

Wireless-G Media Storage Link Router with SpeedBooster

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Router Name. In this field, you can type a name of up to 39 characters to represent the Router.

Host Name/Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. The default setting, Manual, allows you to enter the largest packet size that will be transmitted. The recommended size, entered in the Size field, is 1492. You should leave this value in the 1200 to 1500 range. To have the Router select the best MTU for your Internet connection, select Auto.

Network Setup

The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless Setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet Mask as seen by your network.

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router’s DHCP server option, you must configure all of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on your network.

DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, or you don’t want a DHCP server, then click the Disable radio button (no other DHCP features will be available).

Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the Router’s default IP address is 192.168.1.1, the Starting IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253. The default Starting IP Address is 192.168.1.100.

Chapter 6: Configuring the Wireless-G Media Storage Link Router

Figure 5-9: Optional Settings

Figure 5-10: Router IP

Figure 5-11: Network Address Server Settings

16

The Setup Tab - Basic Setup

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 802 GHz .11g Wireless- G Word definition How to Use This User GuideCopyright and Trademarks Table of Contents Appendix C Upgrading Firmware Appendix D Windows Help Appendix a TroubleshootingAppendix B Wireless Security Common Problems and Solutions Frequently Asked QuestionsRouter’s Back Panel List of Figures25 Wireless Tab Wireless Security Radius 58 The Traceroute Test Welcome IntroductionWhat’s in this User Guide? Wireless-G Media Storage Link Router with SpeedBooster Network Topology Planning Your Wireless NetworkAd-Hoc versus Infrastructure Mode Ssid service set identifier your wireless network’s namePlanning Your Wireless Network Network Layout Back Panel Getting to Know the Wireless-G Media Storage Link RouterDMZ Front PanelInstructions for Connecting the Router Connecting the Wireless-G Media Storage Link RouterConnect Your Network Devices Wall-Mount Option Placement OptionsStand Option Wall-Mount Slots Overview Configuring the Wireless-G Media Storage Link RouterInternet Connection Type Setup Tab Basic SetupInternet Setup PPPoE Connection Type L2TP Connection Type Router IP Network SetupOptional Settings Network Address Server Settings Dhcp12 Time Setting Time SettingTZO.com Setup Tab DdnsDynDNS.org MAC Clone Setup Tab MAC Address CloneDynamic Routing Setup Tab Advanced RoutingOperating Mode Advanced Routing18 Routing Table Entry List Wireless Network Wireless Tab Basic Wireless Settings20 SecureEasySetup Ready Screen Encryption encoding data transmitted in a network Wireless Tab Wireless SecurityWireless Security 24 Wireless Tab Wireless Security WPA2 Enterprise 25 Wireless Tab Wireless Security Radius Wireless MAC Filter Wireless Tab Wireless MAC FilterAdvanced Wireless Wireless Tab Advanced Wireless SettingsWireless-G Media Storage Link Router with SpeedBooster Block WAN Requests Security Tab FirewallFirewall VPN Passthrough Security Tab VPN PassthroughErase Disk Storage Tab DiskDisk Management Disk DetailCreate Share Storage Tab ShareShare Management SharesGroup Management Storage Tab AdministrationBasic User Management40 Modify Group Properties Database SetupStorage Tab Media Server UPnP Media ServerTo create a policy Access Restrictions Tab Internet AccessInternet Access 46 List of PCs Port Range Applications and Gaming Tab Port Range ForwardPort Range Forward Forwarded Range Applications & Gaming Tab Port TriggeringPort Triggering Triggered RangeDMZ Applications and Gaming Tab DMZEthernet Port Priority Wired QoSApplications and Gaming Tab QoS Device PriorityWireless QoS UPnP Administration Tab ManagementRouter Password Log Administration Tab LogPing Parameters Administration Tab DiagnosticsPing Test Traceroute TestAdministration Tab Config Management Administration Tab Factory DefaultsAdministration Tab Firmware Upgrade Internet Configuration TypeStatus Tab Router Router InformationLocal Network Status Tab Local NetworkWireless Status Tab WirelessNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions Wireless-G Media Storage Link Router with SpeedBooster Open a command prompt. For Windows 98SE and Me TCP Application Start and End Protocol IP Address EnabledCan’t get the Internet game, server, or application to work Wireless-G Media Storage Link Router with SpeedBooster My DSL service’s PPPoE is always disconnecting To start over, I need to set the Router to factory defaultNeed to upgrade the firmware Firmware upgrade failed, and/or the Power LED is flashingPower LED keeps flashing Do not see the Router in my Network Neighborhood Frequently Asked QuestionsHow do I set up additional devices using SecureEasySetup? Cannot write to the USB disk attached to the RouterDoes the Router support IPX or AppleTalk? Where is my SecureEasySetup button?Where is the Router installed on the network? Is IPSec Pass-Through supported by the Router?How can I block corrupted FTP downloads? Does the Router support ICQ send file?Router allows Pptp packets to pass through What is DMZ Hosting?What Ieee 802.11g features are supported? What are the advanced features of the Router?What is the Ieee 802.11g standard? What is the Ieee 802.11b standard?What is roaming? What Ieee 802.11b features are supported?What is ad-hoc mode? What is infrastructure mode?What is WEP? What is ISM band?What is Spread Spectrum? What is DSSS? What is FHSS? And what are their differences?Have excellent signal strength, but I cannot see my network How do I resolve issues with signal loss?Security Threats Facing Wireless Networks Appendix B Wireless SecuritySecurity Precautions Appendix B Wireless Security Wireless-G Media Storage Link Router with SpeedBooster Appendix C Upgrading Firmware Network Neighborhood/My Network Places Appendix D Windows HelpShared Resources Windows 2000 or XP Instructions Windows 98SE or Me InstructionsFigure E-4 MAC Address Filter List For the Router’s Web-based UtilityAppendix F Glossary Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Appendix G Specifications Storage Humidity Limited Warranty Appendix H Warranty InformationFCC Statement Appendix I Regulatory InformationWireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Dual-Band Wireless Access Point Information section in this Guide Appendix J Contact InformationNeed to contact Linksys?

WRTSL54GS specifications

The Linksys WRTSL54GS is a versatile wireless router that has earned a reputation for its robust performance and user-friendly features. A member of the renowned WRT family, it combines a powerful 802.11g wireless capability with a wired Ethernet connection, making it ideal for home and small office environments.

One of the primary features of the WRTSL54GS is its ability to serve as a wireless access point and a router simultaneously. It supports a maximum data transfer rate of up to 54 Mbps, allowing users to enjoy fast internet connectivity. The router operates on the 2.4GHz frequency band, which is suited for routine web browsing, streaming, and online gaming.

The WRTSL54GS supports advanced security features that help protect users' data and privacy. With WPA2 encryption, users can ensure that their wireless networks are secure from unauthorized access. The inclusion of a built-in firewall further enhances network security, making it harder for potential threats to infiltrate the system.

Another standout feature of the WRTSL54GS is its USB port, which allows for the connection of external storage devices. This capability enables file sharing among networked computers, making it convenient to access documents, photos, and multimedia content from multiple devices. Additionally, the USB support can facilitate print sharing, allowing users to connect a printer directly to the router.

Employing Quality of Service (QoS) technology, the WRTSL54GS can prioritize bandwidth for specific applications or devices. This ensures that high-demand activities, such as video streaming or online gaming, receive adequate bandwidth to function smoothly, enhancing the overall user experience.

Installation and configuration are straightforward thanks to the user-friendly web-based interface. Users can easily set up wireless security protocols, manage connected devices, and adjust settings to suit their preferences.

In summary, the Linksys WRTSL54GS combines reliable wireless capabilities, robust security features, and practical functionalities like USB support, making it a compelling choice for anyone looking to enhance their home or small office network. Its ease of use and scalability ensure that it remains a relevant solution even as network demands evolve. Overall, it provides a solid balance of performance and versatility.
Top Page Image Contents