Linksys WRTSL54GS manual To start over, I need to set the Router to factory default

Page 64

Wireless-G Media Storage Link Router with SpeedBooster

11.To start over, I need to set the Router to factory default.

Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings. In other words, the Router will revert to its original factory configuration.

12.I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com.

Follow these steps:

1.Go to the Linksys website at http://www.linksys.com and download the latest firmware.

2.To upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”

13.The firmware upgrade failed, and/or the Power LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Power LED stop flashing:

If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

Set a static IP address on the PC; refer to “Problem #2, I need to set a static IP address.” Use the following IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

Perform the upgrade using the TFTP program or the Administration tab of the Router’s web-based utility.

14.My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial-up connection to the Internet.

There is a setup option to “keep alive” the connection. This may not always work, so you may need to re- establish connection periodically.

1.To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

2.Enter the password, if asked. (The default password is admin.)

3.On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

4.Click the Save Settings button.

5.Click the Status tab, and click the Connect button.

6.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected.

Click the Save Settings button to continue.

If the connection is lost again, follow steps 1- 6 to re-establish connection.

Appendix A: Troubleshooting

57

Common Problems and Solutions

Image 64
Contents 802 GHz .11g Wireless- G Copyright and Trademarks How to Use This User GuideWord definition Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityCommon Problems and Solutions Frequently Asked Questions Appendix C Upgrading Firmware Appendix D Windows HelpList of Figures Router’s Back Panel25 Wireless Tab Wireless Security Radius 58 The Traceroute Test Introduction WelcomeWhat’s in this User Guide? Wireless-G Media Storage Link Router with SpeedBooster Planning Your Wireless Network Ad-Hoc versus Infrastructure ModeSsid service set identifier your wireless network’s name Network TopologyPlanning Your Wireless Network Network Layout Getting to Know the Wireless-G Media Storage Link Router Back PanelFront Panel DMZConnecting the Wireless-G Media Storage Link Router Instructions for Connecting the RouterConnect Your Network Devices Stand Option Placement OptionsWall-Mount Option Wall-Mount Slots Configuring the Wireless-G Media Storage Link Router OverviewInternet Setup Setup Tab Basic SetupInternet Connection Type PPPoE Connection Type L2TP Connection Type Network Setup Optional SettingsNetwork Address Server Settings Dhcp Router IPTime Setting 12 Time SettingDynDNS.org Setup Tab DdnsTZO.com Setup Tab MAC Address Clone MAC CloneSetup Tab Advanced Routing Operating ModeAdvanced Routing Dynamic Routing18 Routing Table Entry List Wireless Tab Basic Wireless Settings Wireless Network20 SecureEasySetup Ready Screen Wireless Security Wireless Tab Wireless SecurityEncryption encoding data transmitted in a network 24 Wireless Tab Wireless Security WPA2 Enterprise 25 Wireless Tab Wireless Security Radius Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced WirelessWireless-G Media Storage Link Router with SpeedBooster Firewall Security Tab FirewallBlock WAN Requests Security Tab VPN Passthrough VPN PassthroughStorage Tab Disk Disk ManagementDisk Detail Erase DiskStorage Tab Share Share ManagementShares Create ShareStorage Tab Administration BasicUser Management Group Management40 Modify Group Properties Setup Storage Tab Media ServerUPnP Media Server DatabaseInternet Access Access Restrictions Tab Internet AccessTo create a policy 46 List of PCs Port Range Forward Applications and Gaming Tab Port Range ForwardPort Range Applications & Gaming Tab Port Triggering Port TriggeringTriggered Range Forwarded RangeApplications and Gaming Tab DMZ DMZWired QoS Applications and Gaming Tab QoSDevice Priority Ethernet Port PriorityWireless QoS Router Password Administration Tab ManagementUPnP Administration Tab Log LogAdministration Tab Diagnostics Ping TestTraceroute Test Ping ParametersAdministration Tab Firmware Upgrade Administration Tab Factory DefaultsAdministration Tab Config Management Configuration Type Status Tab RouterRouter Information InternetStatus Tab Local Network Local NetworkStatus Tab Wireless WirelessCommon Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC Wireless-G Media Storage Link Router with SpeedBooster Open a command prompt. For Windows 98SE and Me Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Wireless-G Media Storage Link Router with SpeedBooster To start over, I need to set the Router to factory default Need to upgrade the firmwareFirmware upgrade failed, and/or the Power LED is flashing My DSL service’s PPPoE is always disconnectingPower LED keeps flashing Frequently Asked Questions How do I set up additional devices using SecureEasySetup?Cannot write to the USB disk attached to the Router Do not see the Router in my Network NeighborhoodWhere is my SecureEasySetup button? Where is the Router installed on the network?Is IPSec Pass-Through supported by the Router? Does the Router support IPX or AppleTalk?Does the Router support ICQ send file? How can I block corrupted FTP downloads?What is DMZ Hosting? Router allows Pptp packets to pass throughWhat are the advanced features of the Router? What is the Ieee 802.11g standard?What is the Ieee 802.11b standard? What Ieee 802.11g features are supported?What Ieee 802.11b features are supported? What is ad-hoc mode?What is infrastructure mode? What is roaming?What is ISM band? What is Spread Spectrum?What is DSSS? What is FHSS? And what are their differences? What is WEP?How do I resolve issues with signal loss? Have excellent signal strength, but I cannot see my networkSecurity Precautions Appendix B Wireless SecuritySecurity Threats Facing Wireless Networks Appendix B Wireless Security Wireless-G Media Storage Link Router with SpeedBooster Appendix C Upgrading Firmware Shared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Windows 98SE or Me Instructions Windows 2000 or XP InstructionsFor the Router’s Web-based Utility Figure E-4 MAC Address Filter ListAppendix F Glossary Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Appendix G Specifications Storage Humidity Appendix H Warranty Information Limited WarrantyAppendix I Regulatory Information FCC StatementWireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Wireless-G Media Storage Link Router with SpeedBooster Dual-Band Wireless Access Point Need to contact Linksys? Appendix J Contact InformationInformation section in this Guide

WRTSL54GS specifications

The Linksys WRTSL54GS is a versatile wireless router that has earned a reputation for its robust performance and user-friendly features. A member of the renowned WRT family, it combines a powerful 802.11g wireless capability with a wired Ethernet connection, making it ideal for home and small office environments.

One of the primary features of the WRTSL54GS is its ability to serve as a wireless access point and a router simultaneously. It supports a maximum data transfer rate of up to 54 Mbps, allowing users to enjoy fast internet connectivity. The router operates on the 2.4GHz frequency band, which is suited for routine web browsing, streaming, and online gaming.

The WRTSL54GS supports advanced security features that help protect users' data and privacy. With WPA2 encryption, users can ensure that their wireless networks are secure from unauthorized access. The inclusion of a built-in firewall further enhances network security, making it harder for potential threats to infiltrate the system.

Another standout feature of the WRTSL54GS is its USB port, which allows for the connection of external storage devices. This capability enables file sharing among networked computers, making it convenient to access documents, photos, and multimedia content from multiple devices. Additionally, the USB support can facilitate print sharing, allowing users to connect a printer directly to the router.

Employing Quality of Service (QoS) technology, the WRTSL54GS can prioritize bandwidth for specific applications or devices. This ensures that high-demand activities, such as video streaming or online gaming, receive adequate bandwidth to function smoothly, enhancing the overall user experience.

Installation and configuration are straightforward thanks to the user-friendly web-based interface. Users can easily set up wireless security protocols, manage connected devices, and adjust settings to suit their preferences.

In summary, the Linksys WRTSL54GS combines reliable wireless capabilities, robust security features, and practical functionalities like USB support, making it a compelling choice for anyone looking to enhance their home or small office network. Its ease of use and scalability ensure that it remains a relevant solution even as network demands evolve. Overall, it provides a solid balance of performance and versatility.