ACTiSYS PP2-5600 For Connecting Psion using Serial Cable, Psion 5 Remote Dial-Up Connection Setup

Page 15

Infrared Modem User’s Manual

For Connecting PSION using Serial Cable

This section uses PSION 5 as an example.

(1)Hardware needed

1.Pegasus III series modem

2.Psion 5

3.Null modem cable

(The Serial Cable synchronizes the PSION 5 and the Pegasus modem. One end of the cable is a 9-pin RS-232 male connector that connects to the female RS232 9-pin serial cable provided by PSION series 5. The other end is the PCMCIA male connector that connects to Pegasus modem. Please follow the following steps)

(2)Software needed Message Suite

(Using your PC, go to www.psion.com and download software for modem control. The modem software consists of (E-mail), web, and modem setup software). The software is called "Message Suite" and it is available at www.psion.com/downloads/mssgsuite.html (After downloading and installing "Message Suite" to the your PSION 5, verify that the software has been successfully installed.)

(3)Connect the modem to PSION 5 series

Connect one end of the male 9-pin RS-232 (shorter one, included) into the female 9-pin RS-232 cable connected to the rear of the PSION 5. Connect the other end

of the PCMCIA connector into the socket to the rear of the modem.

(Refer to the connection diagram on next page)

Insert one end of the phone cord (included) into the Pegasus modem’s LINE jack and plug the other end into any analog phone jack. Important: Connect to an analog line only. Using a non-analog line (e.g., digital, PBX, Multi line) may damage the modem.

(4)PSION 5 Remote Dial-Up Connection Setup

1.Tap on "Extras". You should see web and e-mail. If you don’t, then you need to reinstall the software. Contact PSION for assistance.

2.Continue by going to "Control panel", and tap on "Modem". Choose "Hayes compatible modem" under Modem Settings, and then tap "Edit"

2003/11 From 3JTech

Revision 1.0

Page 15 of 41

Page 14 Page 16
Image 15
Page 14 Page 16
Contents April 11, 2002 YLYang/Pre-release July 5, 2002 WWJ/Proofread Introduction Introduction II K Access Information Before You Start III. Hardware InstallationRear View Battery CompartmentSystem Requirements Front ViewConnect the modem to a PC through the Serial Cable Setting Your ModemRed Power-Down ModeBy Serial Port GreenFor Palm Organiser IV. Software Installation GuideNetwork Set-up Infrared Modem User’s Manual Pocket PC Modem setting For Windows CE/Pocket PCChoose Advanced…. icon Step Pocket PC Connections settingEnter your Smtp mail server Internet Explorer settingsMail settings Choose New ServiceFor Connecting Psion using Serial Cable Psion 5 Remote Dial-Up Connection SetupThis section uses Psion 5 as an example Hardware needed To set up an Email Account To set up your Fax informationTap on Initialization To Email or browse the web on Internet This section uses Psion 618C as an example For Connecting Psion using IrDA PortInfrared Modem User’s Manual Infrared Modem User’s Manual For Penbex Infrared Modem User’s Manual Infrared Modem User’s Manual For Sharp Infrared Modem User’s Manual Infrared Modem User’s Manual Infrared Modem User’s Manual For Windows98/Me/2000/XP Choose Virtual Infrared COM Port for IR Modem, Click Next ModemMrom Infrared Modem User’s Manual Remember the following before contacting Technical SupportMCU VI. SpecificationSoftware HardwareStandard Warranty Service Warranty Exclusive Limitation of LiabilityDisclaimer Infrared Modem User’s Manual Appendix AWindows98 IR setupR220L/210L/200L Infrared Modem User’s Manual Infrared Modem User’s Manual Appendix BCountry code setting Appendix CAdvanced AT Commands For Debug
Top Page Image Contents