Airlink101 AR685W user manual Advanced Settings

Page 45

3.2.4 Advanced Settings

You can set advanced wireless LAN parameters of this router. The parameters include Authentication Type, Fragment Threshold, RTS Threshold, Beacon Interval, Preamble Type, etc. It is suggested not to change these parameters unless you know what effect the changes will have on this router.

Parameters

Description

Fragment Threshold

“Fragment Threshold” specifies the maximum size of packet

 

during the fragmentation of data to be transmitted. The default

 

value is 2346.

RTS Threshold

When the packet size is smaller than the RTS threshold, the

 

wireless router will not use the RTS/CTS mechanism to send this

 

packet.

Beacon Interval

The interval of time that this wireless router broadcast a beacon.

 

Beacon is used to synchronize the wireless network.

DTIM Period

Set the DTIM period of wireless radio. Do not modify default

 

value if you don’t know what it is, default value is 3.

Data Rate

Set the wireless data transfer rate to a certain value. Since most

 

of wireless devices will negotiate with each other and pick a

 

proper data transfer rate automatically, it’s not necessary to

 

change this value unless you know what will happen after

 

modification.

N Data Rate

Same as above, but only for 802.11n clients.

46

Image 45
Contents Wireless N 300 Green Router Federal Communication Commission Interference Statement Table of Contents Troubleshooting Technical Support Package Contents FeaturesFront Panel LEDs Router InterfaceAntenna a Antenna B Using EZ Setup Wizard Installing the RouterPage Page Dynamic IP Cable Modem users PPPoE DSL users Page Congratulations! Your router configuration has been finished Connecting to the Router Wirelessly Page Using Web Configuration Utility Page Setup Wizard Enable NTP UpdateCurrent Time Time Server Address Time ZoneDaylight Savings Host NameSecondary DNS Primary DNSService Name PasswordUser Name Connection TypePptp Connection ID Pptp GatewayL2TP Gateway Telstra Big PondServer IP Address Assign login server manuallyBand Channel NumberAssociated Clients WPA2AES Page 1 WAN NetworkIP address 2 LANSubnet Mask 802.1d Spanning TreeLease Time Enable Static Dhcp LeasesDhcp Client Start IP Dhcp Client End IPPage NAT / Static Routing Delete All DeleteDdns Password/KeyDynamic DNS ProviderBasic Settings WirelessShow Active Clients Enable 802.1x Authentication Wireless SecurityEncryption See 3.2.2.1 to 3.2.2.3 for each encryption typeDefault Tx Key Key LengthKey Format Encryption Key 1~4 WPA Pre-share KeyWPA Unicast Cipher Suite Radius Server PasswordPre-shared Key Format Pre-shared KeyMAC Control Enable MAC ControlComment ClearPage Advanced Settings Channel Width Tx PowerPreamble Type Broadcast Essid5 WPS Page Config Mode Enable WPSConfigure by Push Button Configure by Client PinCodeVirtual Server Port Forwarding Application & GamingYou can also click ‘Reset’ button to unselect all Special Applications Port Triggering Enable Special ApplicationsTCP/UDP Port to Open Popular ApplicationAdd in red box Parameter Description3 DMZ Enable DMZPublic IP Client PC IP addressButton ALG Settings 5 QoS Move Down Move UpRule Name BandwidthProtocol Traffic TypeEnable IP & Port Filtering Access Restrictions1 IP & Port Filtering Deny/AllowClient Service Client PC DescriptionPort Range Page MAC Filtering Enable MAC FilteringClient PC MAC Address Current MAC Filtering TableIf you want to delete a specific MAC address entry, check 3 URL/Keyword Filtering Enable URL FilteringURL/Keyword Current URL Blocking TableFirewall SecurityDoS Denial-of-Service Ping of Death IPsec pass through VPN Pass throughPptp pass through L2TP pass throughTime AdministrationNew Password Current PasswordConfirmed Password ManagementReset Reboot Remote Management Firmware Upgrade Backup Settings Configuration SettingsRestore Settings Restore to Factory Default6 Log SaveRefresh Statistics Status Internet Connection StatusLAN Status System Status Wlan Wireless LAN StatusTroubleshooting Technical Support