Airlink101 AR685W user manual Federal Communication Commission Interference Statement

Page 2

Federal Communication Commission

Interference Statement

FCC Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4.Consult the dealer or an experienced radio technician for help.

FCC Caution

This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The equipment version marketed in US is restricted to usage of the channels 1-11 only.

Image 2
Contents Wireless N 300 Green Router Federal Communication Commission Interference Statement Table of Contents Troubleshooting Technical Support Features Package ContentsRouter Interface Front Panel LEDsAntenna a Antenna B Installing the Router Using EZ Setup WizardPage Page Dynamic IP Cable Modem users PPPoE DSL users Page Congratulations! Your router configuration has been finished Connecting to the Router Wirelessly Page Using Web Configuration Utility Page Current Time Setup WizardEnable NTP Update Daylight Savings Time ZoneTime Server Address Host NamePrimary DNS Secondary DNSUser Name PasswordService Name Connection TypePptp Pptp Gateway Connection IDTelstra Big Pond L2TP GatewayAssign login server manually Server IP AddressAssociated Clients BandChannel Number WPA2AES Page Network 1 WANSubnet Mask 2 LANIP address 802.1d Spanning TreeDhcp Client Start IP Enable Static Dhcp LeasesLease Time Dhcp Client End IPPage NAT / Static Routing Delete Delete AllDynamic DNS Password/KeyDdns ProviderWireless Basic SettingsShow Active Clients Encryption Wireless SecurityEnable 802.1x Authentication See 3.2.2.1 to 3.2.2.3 for each encryption typeKey Format Default Tx KeyKey Length WPA Pre-share Key Encryption Key 1~4Pre-shared Key Format Radius Server PasswordWPA Unicast Cipher Suite Pre-shared KeyComment Enable MAC ControlMAC Control ClearPage Advanced Settings Preamble Type Tx PowerChannel Width Broadcast Essid5 WPS Page Configure by Push Button Enable WPSConfig Mode Configure by Client PinCodeApplication & Gaming Virtual Server Port ForwardingYou can also click ‘Reset’ button to unselect all TCP/UDP Port to Open Enable Special ApplicationsSpecial Applications Port Triggering Popular ApplicationParameter Description Add in red boxPublic IP Enable DMZ3 DMZ Client PC IP addressButton ALG Settings 5 QoS Rule Name Move UpMove Down BandwidthTraffic Type Protocol1 IP & Port Filtering Access RestrictionsEnable IP & Port Filtering Deny/AllowPort Range Client ServiceClient PC Description Page Client PC MAC Address Enable MAC FilteringMAC Filtering Current MAC Filtering TableIf you want to delete a specific MAC address entry, check URL/Keyword Enable URL Filtering3 URL/Keyword Filtering Current URL Blocking TableSecurity FirewallDoS Denial-of-Service Ping of Death Pptp pass through VPN Pass throughIPsec pass through L2TP pass throughAdministration TimeConfirmed Password Current PasswordNew Password ManagementReset Reboot Remote Management Firmware Upgrade Restore Settings Configuration SettingsBackup Settings Restore to Factory DefaultRefresh 6 LogSave Statistics LAN Status StatusInternet Connection Status Wlan Wireless LAN Status System StatusTroubleshooting Technical Support