Olympus V403121SU000 Discharging, Operating temperature, Recommended temperature range, Charging

Page 16

Power supply

1

Power supply

EN

Notes

Insert the supplied rechargeable battery and set [Battery] to [Ni-MH]. If [Battery] is set to [Alkaline], you cannot recharge (P.13).

You cannot charge when [ø]*1 or [√]*2

blinks. Charge the batteries at a temperature in

the range of 5°C to 35°C (41°F to 95°F).

*1 [ø]: When the surrounding temperature is low.

*2 [√]: When the surrounding temperature is high.

When using time becomes notably short even after the batteries are fully charged, replace them with new ones.

Be sure to push the USB connector all the way in. Otherwise, the recorder may not operate properly.

Be sure to use the included dedicated USB cable. If any other company’s cable is used, it may lead to malfunction of the recorder. Also, never use this dedicated cable with any other company’s products.

If selecting [Composite] in the USB connection settings:

-Charge will not be possible if the recorder is operating. Charge will start 1 minute after the end of the operation.

-Charge may not be possible depending on the application in use on the computer connected.

In case you would like to charge using the

[Composite] setting, select [Optional] in the USB connection settings, then connect the USB cable to the recorder. Selecting [AC Adapter] at the [USB Connect] display will enable you to charge (P.48).

Cautions concerning the rechargeable batteries

Read the following descriptions carefully when you use the Ni-MH rechargeable batteries.

Discharging:

Rechargeable batteries self-discharge while not in use. Be sure to charge them regularly before use.

Operating temperature:

The rechargeable batteries are chemical products. The rechargeable batteries efficiency may fluctuate even when operating within the recommended temperature range. This is an inherent nature of such products.

Recommended temperature range:

When operating appliance: 0°C - 42°C/ 32°F - 107.6°F

Charging:

5°C - 35°C/ 41°F - 95°F

Storage for a long period: –20°C - 30°C/ –4°F - 86°F

Using the rechargeable batteries outside the above temperature range may result in declining efficiency and shorter battery life. In order to prevent battery leakage or rust, remove the rechargeable batteries from the products when you will not be using them for a long time, and store them separately.

Notes

This recorder is designed to fully charge batteries regardless of their energy level. However, for best results when charging newly purchased rechargeable batteries or batteries that have not been used for a long time (more than one month), it is recommended to fully charge the batteries then discharge repeatedly for 2 to 3 times.

When disposing rechargeable batteries, always observe the local laws and regulations. Contact your local recycling center for proper disposal methods.

If Ni-MH rechargeable batteries are not fully discharged, protect against short-circuiting (e.g. by taping the contacts) before disposing.

16

Image 16
Contents Thank you for purchasing an Olympus Digital Voice Recorder Keep the instructions handy for future referenceIntroduction TrademarksIndex Table of contents Safe and proper usage Convention used in this manualBattery handling precautions Handling the recorderFCaution FWarningKeep batteries away from fire Keep batteries out of the reach of childrenDo not subject batteries to strong shocks Main features Main featuresRecorder to your computer Compatible cards Memory cardCheck card information Card Info MIC Microphone jack @ Record indicator light Identification of partsIdentification of parts Display status indicators LCD panelParts Power supply Power supplyInserting batteries Unusable batteries Power supply Battery settings Press the PLAY/OK button to complete the setting Battery indicatorPower supply Charging by connecting to a computer via Press the PLAY/OK button to start chargingConnecting the USB-type AC adapter optional to charge Charging is completed when Battery Full is displayedPlug the recorder’s USB cable into the AC adapter Plug the AC adapter into AC outletOperating temperature Recommended temperature rangeDischarging ChargingTurning on/off the power Power Save Mode Power SaveTurning on the power Turning off the powerSet the recorder to Hold mode Slide the POWER/HOLD switch to the Hold positionExit Hold mode Slide the POWER/HOLD switch to the a positionInserting and ejecting a SD card Inserting and ejecting a SD cardInserting a SD card Ejecting a SD cardSetting time and date Time & Date Press the 9or 0button to select the item to setDate Press the + or − button to setSetting time and date Time & Date 10M 14D 2012Y Initial setting 14D 10M 2012Y 2012Y 10M 14DChanging the time and date Press the PLAY/OK or 9buttonRecording related settings RecordingRecording Record functionRecording New recordingFile Press the Stop button to stop recordingSelect and play the file you want to overwrite Overwrite recordingPress the Stop button to stop overwriting Insert recording 00M 11sRecording modes Rec Mode Recording modesPress the + or button to select QP or SP Press the F3 Exit or 0button to close the menu screenMicrophone sensitivity Mic Sense Press the + or button to select Conference or DictationAdjust the start/stop actuation level Using the Variable Control Voice ActuatorPress the REC button to start recording Set the Vcva in the menu to OnRecording monitor +, − Volume buttonRecording monitor Playback PlaybackPlayback Erasing Erasing a fileErasing Select the file you want to erase Press the Erase buttonErasing Erasing all files in a folderPartially erasing a file Press the Erase button at the point to end erasingPress the Erase button to confirm erase Selecting folders and files Changing fileChanging folders While the file is being displayed, press the 9or 0buttonDisplaying file information Information Select the file containing the information to displayPress the F2 Info button File informationSetting an index mark Index marksLocating an index mark Clearing an index markMenu list Menu listMenu list Learning to use the menu Press the F3 Menu buttonPress the + or button to move to Main Menu item to be set Press the + or button to move to the menu item to be setLocking files Lock Select the file you want to lockPress the + or button to select On or Off Locking filesBacklight Backlight LCD contrast adjustment LCD contrast adjustment ContrastPress the + or button to set the contrast level LED LED Language Language LanguagePress the + or button to set the language Press the F3 Exit or 0 button to close the menu screenSystem sounds Beep Changing the USB class USB Settings When USB Connect is selectedChanging the USB class Press the PLAY/OK buttonChanging the USB class USB Settings When USB Class is selectedFormatting the card Format Press the + or button to select Start optionFormatting the card Press the PLAY/OK button to confirm Start selectionFormatting the card Format Initializing the recorder’s menu settings Reset SettingsFormatting the card Model Name Version Serial will appear Check system information System infoF1, F3 button PLAY/OK button DSS Player Software Minimum requirementDSS Player Software WindowsInstalling software Be sure to confirm the following before installationInsert Olympus DSS Player CD into the CD-ROM drive Launcher will startupUninstalling software Using online help Uninstalling software / Using online helpClick the start button, then select While DSS Player is running, press F1 on the keyboardConnecting to your PC using the USB cable Connecting recorder to PCConnecting recorder to PC Connecting recorder to PC Disconnecting from your PCRunning DSS Player Software Running DSS Player SoftwareClick DSS Player Standard Click the start button, then select All ProgramsUsing as external memory of the computer Alarm message list Alarm message listMessage Explanation Action Troubleshooting TroubleshootingSymptom Probable cause Action Troubleshooting/Technical assistance and support Technical assistance and supportSupport User Support E-mail address in EuropeAccessories optional Specifications Olympus Imaging Corp