Honeywell 4800dr manual Concatenation of Multiple Commands, Responses, Examples of Query Commands

Page 106

Tag Field Usage

When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular storage table indicated by the Storage field of the command. In this case, the SubTag and Data fields should not be used because they are ignored by the device.

SubTag Field Usage

When a query is used in place of a SubTag field, the query applies only to the subset of commands avail- able that match the Tag field. In this case, the Data field should not be used because it is ignored by the device.

Data Field Usage

When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields.

Concatenation of Multiple Commands

Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are issued. If the additional command requires a dif- ferent Tag field, the command is separated from previous commands by a semicolon (;).

Responses

The device responds to serial commands with one of three responses:

ACK Indicates a good command which has been processed.

ENQ Indicates an invalid Tag or SubTag command.

NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.

When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.

Examples of Query Commands

In the following examples, a bracketed notation [ ] depicts a non-displayable response.

Example #1: What is the range of possible values for Codabar Coding Enable?

Enter: cbrena*.

Response: CBRENA0-1[ACK]

This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on).

Example #2: What is the default value for Codabar Coding Enable?

Enter: cbrena^.

Response: CBRENA1[ACK]

This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.

10 - 2

Image 106

Contents 4800dr Disclaimer Table of Contents Data Editing UPC-A UPC-A/EAN-13 Interface Keys Product Specifications OCR Programming Chart About This Manual Connecting the Document Reader with USBGetting Started Unpacking the Document ReaderConnecting the Document Reader with TTL-232 Serial Port USB Connection Supported TerminalsProgramming the Interface Plug and Play IBM SurePosUSB PC or Macintosh Keyboard USB COM Port EmulationTTL-232 Serial Port Connection Aligning the Document Reader TrayLinear barcodes 2D Matrix symbols Using the Imager Out of the StandReading Techniques Terminal Interfaces Keyboard CountryKeyboard Style Keyboard CountryKeyboard Modifiers TTL-232 Baud Rate TTL-232 Receiver Time-Out RS-232 Word Length Data Bits, Stop Bits, and ParityRS-232 Handshaking Page Output Good Read IndicatorsBeeper Volume Good Read Beeper Good ReadLED Good Read LED Indicator StateBeeper Duration Good Read Number of Beeps Good ReadTrigger Modes Good Read DelayUser-Specified Good Read Delay Manual/Serial TriggerPresentation Mode Scan Stand ModeScan Stand Symbol Hands Free Time-Out Reread DelayPresentation Sensitivity LED Power Level User-Specified Reread DelayImager Time-Out User-Specified Aimer Delay Aimer DelayAimer Mode CenteringTom and Right Decode Window Decode Search Mode Preferred SymbologyPreferred Symbology Time-out High Priority SymbologyLow Priority Symbology Preferred Symbology DefaultRequire Output Sequence Output Sequence OverviewOutput Sequence Editor Output Sequence Examples SeqblkMultiple Symbols Video Reverse Print WeightNo Read Mandatory Alignment FlagWorking Orientation Prefix/Suffix Overview Data EditingPoints to Keep In Mind To Clear One or All Prefixes or Suffixes Scan the Add Prefix or Add Suffix symbolTo Add a Prefix or Suffix Scan Add SuffixPrefix Selections To Add a Carriage Return Suffix to all SymbologiesScan the Clear One Prefix or Clear One Suffix symbol Suffix SelectionsUser Specified Intercharacter Delay Intercharacter, Interfunction, and Intermessage DelaysIntercharacter Delay Function Code TransmitInterfunction Delay Intermessage DelayPage Data Format Editor Introduction Scan the Enter Data Format symbol Primary/Alternate FormatData Formatting To Add a Data FormatOther Programming Selections Data Format Editor CommandsEditor Commands Clear One Data FormatMove Commands Data Formatter Data Format EditorAlternate Data Formats Alternate Data Format Page Symbologies MSICodabar Start/Stop Characters Message Length DescriptionCodabar Check Character Codabar Concatenation Codabar Message LengthCode 39 Start/Stop Characters Code 39 Check CharacterCode 39 Append Code 39 Message LengthCode 32 Pharmaceutical Paraf Full Ascii Code 39 CodeCheck Digit Interleaved 2 of 5 Message LengthCode 93 Message Length Code 93 CodeStraight 2 of 5 Industrial Message Length Straight 2 of 5 Iata Straight 2 of 5 Iata Message LengthMatrix 2 of 5 Message Length Code 11 Message Length Check Digits RequiredIsbt 128 Concatenation Code 128 Message Length Code 128 CodeTelepen Output Telepen Message LengthUPC-A Check Digit UPC-A Number SystemUPC-A Addenda Required UPC-A AddendaUPC-A Addenda Separator UPC-E0 Addenda Required UPC-E0 ExpandUPC-E0 Addenda Separator UPC-E0 Number System UPC-E0 Check DigitUPC-E0 Addenda EAN/JAN-13 Check Digit EAN/JAN-13 AddendaEAN/JAN-13 Addenda Separator EAN/JAN-13 Addenda RequiredIsbn Translate EAN/JAN-8 Check Digit EAN/JAN-8 AddendaEAN/JAN-8 Addenda Separator EAN/JAN-8 Addenda RequiredMSI Check Character MSI Message Length Plessey Message LengthGS1 DataBar Expanded Message Length PosiCode a and B PosiCode Message LengthCodablock F Message Length Code 16K Message Length Code 49 Message Length Minimum Message Length Maximum Message Length Off Eanucc Composite Codes UPC/EAN VersionEanucc Emulation Eanucc Composite Code Message LengthPostnet Intelligent Mail BarcodeID-tag UPU 4-State Postnet Check DigitBritish Post Planet CodePlanet Code Check Digit Canadian PostAustralian Post Australian Post InterpretationChina Post Japanese PostChina Post Message Length Korea Post Korea Post Message LengthQR Code Message Length Data Matrix Message LengthMaxiCode Message Length Aztec Code Message LengthAztec Runes Page OCR Programming OCR FontsOCR Templates Currency FontCreating an OCR Template Template CharactersStringing Together Multiple Formats Creating Or Statements Adding SpacesOCR User-Defined Variables Reading Multi-Row OCROCR Check Character OCR Modulo 10 Check CharacterProgramming a User-Defined Check Character OCR User-Defined Check CharacterOCR Modulo 36 Check Character Scan the Enter OCR Check Character barcode, belowWeighting Options Weighted Modulo 10 Check CharacterOCR Isbn Application Example 0128454OCR Template Codes Exit SelectionsInterface Keys Keyboard Function RelationshipsSupported Interface Keys Ascii HEXUtilities Test Menu Resetting the Standard Product DefaultsShow Data Format 2D PQA Print Quality AssessmentVisual Xpress Operations ConfigureVisual Xpress Introduction Scan DataImaging Installing Visual Xpress from the WebHeld Products-Visual Xpress Query Commands Serial Programming CommandsMenu Command Syntax ConventionsExamples of Query Commands Concatenation of Multiple CommandsResponses Enter cbr? Response CBRENA1ACK Trigger CommandsEnter cbrena? Response CBRENA1ACK CK20ACKSetting Serial Selection Command Menu CommandsTerminal Interfaces Output Selections KBDNPS1BEPBIP0 DECWIN1 Symbologies Prefix/Suffix SelectionsCBRCCT0 CBRCCT1 C93DCP TELENA0 TELENA1 UPEAD21 MSICHK0 C49DFT PLNCKX1 OCR Selections Product Specifications Parameter SpecificationPage Standard Cable Pinouts Serial OutputPage Maintenance MaintenanceRepairs Troubleshooting To Replace the Interface CableDocument reader won’t read your barcode at all Page Technical Assistance Product Service and RepairCustomer Support Online Technical AssistanceOnline Product Service and Repair Assistance Limited WarrantyNorth America Page Page Appendix a Symbology ChartSymbology Possible AIM ID Code ID hex Modifiers mOCR-B1 Ascii Conversion Chart Code Hex CharCode Page Mapping of Printed Barcodes Code Standard DescriptionPage Page Page Sample Symbols QR Code OCR Programming Chart Discard Save Programming Chart Save Discard Honeywell

Related manuals

Manual 2 pages 56.38 Kb