Advantech HMI-640S user manual SA0 ISA

Page 51

36	SA0	ISA	108	LA21	ISA
37	LA23	ISA	109	SA1	ISA

38	SA2	ISA	110	SA4	ISA

39	SA6	ISA	111	SA3	ISA

40	HDD0	IDE	112	SA7	ISA
41	HDD8	IDE	113	SA5	ISA

42	HDD2	IDE	114	HDD11	IDE

43	HDD1	IDE	115	HDD3	IDE

44	HDD6	IDE	116	HDD5	IDE
45	HDD10	IDE	117	HDD4	IDE

46	HDD7	IDE	118	HDD9	IDE

47	HDD14	IDE	119	HDD15	IDE

48	HDD13	IDE	120	HDD12	IDE
49	SD8	ISA	121	SD0	ISA

50	SD10	ISA	122	SD2	ISA

51	SD11	ISA	123	SD3	ISA

52	SD9	ISA	124	SD4	ISA

53	SD14	ISA	125	SD1	ISA

54	SD13	ISA	126	SD6	ISA

55	SD12	ISA	127	SD7	ISA
56	BALE	ISA	128	SD5	ISA

57	SD15	ISA	129	IOCHRDY	ISA

58	SMEMR	ISA	130	MEMW	ISA

59	SBHE	ISA	131	IOR	ISA
60	MEMR	ISA	132	MASTER	ISA

61	IOCS16	ISA	133	SMEMW	ISA

62	IOCHCK	ISA	134	MEMCS16	ISA

63	REFRESH	ISA	135	IOW	ISA
64	ACK	PRT	136	AEN	ISA

65	PE	PRT	137	BUSY	PRT

66	PD6	PRT	138	PD5	PRT

67	PD4	PRT	139	PD3	PRT

68	PD2	PRT	140	PD1	PRT

69	PD0	PRT	141	AUTOFD	PRT

70	STROBE	PRT	142	ERR	PRT
71	INIT	PRT	143	PD7	PRT

72	SLCTIN	PRT	144	SLCT	PRT

Chapter 4 CPC-2245N Main Borad

41

Image 51

Contents HMI-640S Copyright notice Acknowledgments FCC Class a notes Safety Instructions Wichtige Sicherheishinweise Contents Maintenance Networking Communication Figures Page General Information Standard functions CPC-2245N SpecificationsIntroduction GeneralPS/2 keyboard/mouse connector Mini-DIN keyboard connector SVGA/Flat panel interface CPC-2520 Power supplyEnvironmental specifications Ethernet interfaceTouchscreen LCD SpecificationsI/O Arrangement COM2 port settingsTotal Solution Dimensions Mounting Page System Setup Packing List GeneralInitial Setup Installing a CompactFlash adapter Installing a CompactFlash Memory CardInstalling a 2.5 HDD Connecting the Power Adapter Installing a PC/104 Module PC/104 module dimensions mm ±5 % First System Boot Power up for the first timeAssign the Device Name Exploded Diagram Maintenance Removing the Front/Rear Panel Maintenance LCD Display LCD Backlight Power Supply I/O Adapter CPC-2900 Core of HMI-640S CPC-2520/CPC-2245N/ CPC-2430 CPC-2245N Main Board Introduction Super I/O chipset Winbond W83977F ISA/IDE/FDD/parallel port 144-pin Sodimm socketMechanical and environmental VGA/LAN/serial port/keyboard/mouse 40-pin FPC connectorBoard layout dimensions Name Function Jumpers and connectorsBoard layout jumper/connector locations Board layout jumper/connector locationsSafety precautions Setting jumpers Clear Cmos J2 CompactFlash interface CN2ISA/IDE/floppy drive/parallel port CN3 Pin Signal Bus SA0 ISA CN3 ISA busGND Rstdrv IRQ9 DRQ2 Memw MEMCS16 IDE interface Pin SignalDamping resistor Floppy drive Parallel port 10 VGA/LAN/serial ports/keyboard/ mouse CN4 VGA interface Keyboard and PS/2 mouse connector Ethernet configurationSerial ports Port Address Default Power supply connector CN5 Card installation Card removal FPC cable installation CPC-2520 VGA/LCD Control Board Introduction Display output Board layout dimensions Number Function Board layout jumper/connector locations Safety precautions Jumper settings LCD panel select SW1 Display connectors CN2, CN3LCD display connector CN2 Model number of the CN3 socket is VGA display connector CN3VGA CN3 FPC cable installation Page Networking Communica- tion Connect or disconnect any cable Networking via LANTo assign the IP addresses to your machines, just Networking via RS-232 RAS service, you must install it on your systemSimple Networking via a Hub Page Cabling for RS-232 Port Pin Null Modem Cable Clear to Send Page DIP Switch Settings Touchscreen Specifications