Advantech HMI-640S user manual Figures

Page 9

 

Figures

 

Figure 4-1: Board layout: jumper/connector locations

35

Figure 4-2: Damping resistor

47

 

Tables

 

Table 4-1:

Jumpers and connectors

34

Table 4-2:

Clear CMOS (J2)

38

Table 4-3:

ISA/IDE/floppy drive/parallel port connector (CN3)

40

Table 4-4:

ISA bus - CN3 cross reference table (ISA pin A)

42

Table 4-5:

ISA bus - CN3 cross reference table (ISA bus pin B)

43

Table 4-6:

ISA bus - CN3 cross reference table (ISA bus pin C)

44

Table 4-7:

ISA bus - CN3 cross reference table (IDE pin D)

45

Table 4-8:

IDE hard drive connector

46

Table 4-9:

Floppy drive connector

48

Table 4-10: Parallel port connector

49

Table 4-11: FPC connector (CN4)

50

Table 4-12: VGA interface

51

Table 4-13: Ethernet configuration

52

Table 4-14: PS/2 keyboard connector

53

Table 4-15: PS/2 mouse connector

53

Table 4-16: Serial port default settings

54

Table 4-17: COM1 RS-232 serial port connector

54

Table 4-18: COM2 RS-232 serial port connector

54

Table 4-19: Power supply connector (CN5)

55

Table 5-1:

Jumpers and connectors

63

Table 5-2: LCD display connector (CN2)

68

Table 5-3:

VGA display connector (CN3)

69

Table 5-4:

VGA display connector (CN3)

70

Page 8 Page 10
Image 9
Page 8 Page 10
Contents HMI-640S Copyright notice Acknowledgments FCC Class a notes Safety Instructions Wichtige Sicherheishinweise Contents Maintenance Networking Communication Figures Page General Information Introduction SpecificationsGeneral Standard functions CPC-2245NPS/2 keyboard/mouse connector Mini-DIN keyboard connector Environmental specifications Power supplyEthernet interface SVGA/Flat panel interface CPC-2520Touchscreen LCD SpecificationsI/O Arrangement COM2 port settingsTotal Solution Dimensions Mounting Page System Setup Packing List GeneralInitial Setup Installing a CompactFlash adapter Installing a CompactFlash Memory CardInstalling a 2.5 HDD Connecting the Power Adapter Installing a PC/104 Module PC/104 module dimensions mm ±5 % First System Boot Power up for the first timeAssign the Device Name Exploded Diagram Maintenance Removing the Front/Rear Panel Maintenance LCD Display LCD Backlight Power Supply I/O Adapter CPC-2900 Core of HMI-640S CPC-2520/CPC-2245N/ CPC-2430 CPC-2245N Main Board Introduction Super I/O chipset Winbond W83977F ISA/IDE/FDD/parallel port 144-pin Sodimm socketMechanical and environmental VGA/LAN/serial port/keyboard/mouse 40-pin FPC connectorBoard layout dimensions Name Function Jumpers and connectorsBoard layout jumper/connector locations Board layout jumper/connector locationsSafety precautions Setting jumpers Clear Cmos J2 CompactFlash interface CN2ISA/IDE/floppy drive/parallel port CN3 Pin Signal Bus SA0 ISA CN3 ISA busGND Rstdrv IRQ9 DRQ2 Memw MEMCS16 IDE interface Pin SignalDamping resistor Floppy drive Parallel port 10 VGA/LAN/serial ports/keyboard/ mouse CN4 VGA interface Keyboard and PS/2 mouse connector Ethernet configurationSerial ports Port Address Default Power supply connector CN5 Card installation Card removal FPC cable installation CPC-2520 VGA/LCD Control Board Introduction Display output Board layout dimensions Number Function Board layout jumper/connector locations Safety precautions Jumper settings LCD panel select SW1 Display connectors CN2, CN3LCD display connector CN2 Model number of the CN3 socket is VGA display connector CN3VGA CN3 FPC cable installation Page Networking Communica- tion Connect or disconnect any cable Networking via LANTo assign the IP addresses to your machines, just Networking via RS-232 RAS service, you must install it on your systemSimple Networking via a Hub Page Cabling for RS-232 Port Pin Null Modem Cable Clear to Send Page DIP Switch Settings Touchscreen Specifications
Top Page Image Contents