Advantech HMI-640S user manual Maintenance

Page 7

Chapter 3 Maintenance		21
3.1	Removing the Front/Rear Panel	22
3.2	LCD Display	24
3.3	LCD Backlight	25
3.4	Power Supply	26
3.5	I/O Adapter (CPC-2900)	27

3.6Core of HMI-640S (CPC-2520/CPC-2245N/CPC-2430) ........................... 28

Chapter 4 CPC-2245N Main Board		29
4.1	Introduction	30
4.2	Specifications	31
	ISA/IDE/FDD/parallel port (144-pin SODIMM socket) ...	31
	VGA/LAN/serial port/keyboard/mouse
	(40-pin FPC connector)	32
	Mechanical and environmental	32
4.3	Board layout: dimensions	33
4.4	Jumpers and connectors	34
4.5	Board layout: jumper/connector locations	35
4.6	Safety precautions	36
4.7	Setting jumpers	37
	4.7.1 Clear CMOS (J2)	38
4.8	CompactFlash interface (CN2)	38
4.9	ISA/IDE/floppy drive/parallel port (CN3)	39
	4.9.1 ISA bus	42
	4.9.2 IDE interface	46
	4.9.3 Floppy drive	48
	4.9.4 Parallel port	49
4.10	VGA/LAN/serial ports/keyboard/mouse (CN4)	50
	4.10.1 VGA interface	51
	4.10.2 Ethernet configuration	52
	4.10.3 Keyboard and PS/2 mouse connector	52
	Table 4-15: PS/2 mouse connector	53
	4.10.4 Serial ports	53
4.11	Power supply connector (CN5)	55

Image 7

Contents HMI-640S Copyright notice Acknowledgments FCC Class a notes Safety Instructions Wichtige Sicherheishinweise Contents Maintenance Networking Communication Figures Page General Information Standard functions CPC-2245N SpecificationsIntroduction GeneralPS/2 keyboard/mouse connector Mini-DIN keyboard connector SVGA/Flat panel interface CPC-2520 Power supplyEnvironmental specifications Ethernet interfaceTouchscreen LCD SpecificationsI/O Arrangement COM2 port settingsTotal Solution Dimensions Mounting Page System Setup Packing List GeneralInitial Setup Installing a CompactFlash adapter Installing a CompactFlash Memory CardInstalling a 2.5 HDD Connecting the Power Adapter Installing a PC/104 Module PC/104 module dimensions mm ±5 % Power up for the first time First System BootAssign the Device Name Exploded Diagram Maintenance Removing the Front/Rear Panel Maintenance LCD Display LCD Backlight Power Supply I/O Adapter CPC-2900 Core of HMI-640S CPC-2520/CPC-2245N/ CPC-2430 CPC-2245N Main Board Introduction Super I/O chipset Winbond W83977F ISA/IDE/FDD/parallel port 144-pin Sodimm socketMechanical and environmental VGA/LAN/serial port/keyboard/mouse 40-pin FPC connectorBoard layout dimensions Name Function Jumpers and connectorsBoard layout jumper/connector locations Board layout jumper/connector locationsSafety precautions Setting jumpers Clear Cmos J2 CompactFlash interface CN2ISA/IDE/floppy drive/parallel port CN3 Pin Signal Bus SA0 ISA CN3 ISA busGND Rstdrv IRQ9 DRQ2 Memw MEMCS16 IDE interface Pin SignalDamping resistor Floppy drive Parallel port 10 VGA/LAN/serial ports/keyboard/ mouse CN4 VGA interface Keyboard and PS/2 mouse connector Ethernet configurationSerial ports Port Address Default Power supply connector CN5 Card installation Card removal FPC cable installation CPC-2520 VGA/LCD Control Board Introduction Display output Board layout dimensions Number Function Board layout jumper/connector locations Safety precautions Jumper settings LCD panel select SW1 Display connectors CN2, CN3LCD display connector CN2 Model number of the CN3 socket is VGA display connector CN3VGA CN3 FPC cable installation Page Networking Communica- tion Connect or disconnect any cable Networking via LANTo assign the IP addresses to your machines, just Networking via RS-232 RAS service, you must install it on your systemSimple Networking via a Hub Page Cabling for RS-232 Port Pin Null Modem Cable Clear to Send Page DIP Switch Settings Touchscreen Specifications