Advantech HMI-640S Ethernet interface, SVGA/Flat panel interface CPC-2520, Power supply

Page 14

Ethernet interface

Chipset: Realtek RTL8139A 10/100 Base-T controller

Network (LAN): Novell NE1000/2000 compatible. Supports both boot ROM function and software drivers

SVGA/Flat panel interface (CPC-2520)

Chipset: C&T 69000

Display memory: 2 MB SDRAM embedded

Hardware Windows acceleration: 32-bit graphic engine. Hardware line drawing and 64 x 64 x 2 hardware cursor

Resolution: 640 x 480 @ 16M colors

 

800 x 600 @ 16M colors

 

1024 x 768 @ 64K colors

Note:

The resolution and hardware Windows acceleration

 

function of the flat panel interface is partially depen-

 

dent on the resolution of the flat panel.

Power supply

Output rating: 25 W

Input voltage: 18 ~ 30 VDC

Output voltage: +5 V @ 4 A, +12 V @ 0.5 A

Environmental specifications

Operating temperature: 0 ~ 45° C (32° ~ 113° F)

Relative humidity: 0 ~ 95% RH (non-condensing), 40° C

Safety: Meets UL/CSA

FCC Class A, CE certified

Vibration: 10 ~ 18 Hz, 1.5 mm peak-to-peak displacement 18 ~ 500 Hz, 1 G acceleration

4 HMI-640S User's Manual

Image 14
Contents HMI-640S Copyright notice Acknowledgments FCC Class a notes Safety Instructions Wichtige Sicherheishinweise Contents Maintenance Networking Communication Figures Page General Information General SpecificationsIntroduction Standard functions CPC-2245NPS/2 keyboard/mouse connector Mini-DIN keyboard connector Ethernet interface Power supplyEnvironmental specifications SVGA/Flat panel interface CPC-2520LCD Specifications TouchscreenCOM2 port settings I/O ArrangementTotal Solution Dimensions Mounting Page System Setup General Packing ListInitial Setup Installing a CompactFlash Memory Card Installing a CompactFlash adapterInstalling a 2.5 HDD Connecting the Power Adapter Installing a PC/104 Module PC/104 module dimensions mm ±5 % Assign the Device Name First System BootPower up for the first time Exploded Diagram Maintenance Removing the Front/Rear Panel Maintenance LCD Display LCD Backlight Power Supply I/O Adapter CPC-2900 Core of HMI-640S CPC-2520/CPC-2245N/ CPC-2430 CPC-2245N Main Board Introduction ISA/IDE/FDD/parallel port 144-pin Sodimm socket Super I/O chipset Winbond W83977FVGA/LAN/serial port/keyboard/mouse 40-pin FPC connector Mechanical and environmentalBoard layout dimensions Jumpers and connectors Name FunctionBoard layout jumper/connector locations Board layout jumper/connector locationsSafety precautions Setting jumpers CompactFlash interface CN2 Clear Cmos J2ISA/IDE/floppy drive/parallel port CN3 Pin Signal Bus SA0 ISA ISA bus CN3GND Rstdrv IRQ9 DRQ2 Memw MEMCS16 Pin Signal IDE interfaceDamping resistor Floppy drive Parallel port 10 VGA/LAN/serial ports/keyboard/ mouse CN4 VGA interface Ethernet configuration Keyboard and PS/2 mouse connectorSerial ports Port Address Default Power supply connector CN5 Card installation Card removal FPC cable installation CPC-2520 VGA/LCD Control Board Introduction Display output Board layout dimensions Number Function Board layout jumper/connector locations Safety precautions Jumper settings Display connectors CN2, CN3 LCD panel select SW1LCD display connector CN2 VGA display connector CN3 Model number of the CN3 socket isVGA CN3 FPC cable installation Page Networking Communica- tion Networking via LAN Connect or disconnect any cableTo assign the IP addresses to your machines, just RAS service, you must install it on your system Networking via RS-232Simple Networking via a Hub Page Cabling for RS-232 Port Pin Null Modem Cable Clear to Send Page DIP Switch Settings Touchscreen Specifications