Advantech HMI-640S user manual Pin Signal Bus

Page 50

Table 4-3: ISA/IDE/floppy drive/parallel port connector (CN3)

Pin	Signal	Bus	Pin	Signal	Bus
1	+5 V	POWER	73	+5 V	POWER

2	ZW	ISA	74	RESET	IDE

3	SA18	ISA	75	RSTDRV	ISA

4	SA19	ISA	76	IRQ3	ISA

5	+5 V	POWER	77	GND	POWER

6	+5 V	POWER	78	DACK7	ISA

7	+5 V	POWER	79	DACK6	ISA
8	TC	ISA	80	DACK5	ISA

9	GND	POWER	81	DACK3	ISA

10	GND	POWER	82	DACK2	ISA

11	GND	POWER	83	DACK1	ISA

12	GND	POWER	84	DACK0	ISA

13	GND	POWER	85	HDCS0	IDE

14	GND	POWER	86	HDCS1	IDE
15	GND	POWER	87	GND	POWER
16	GND	POWER	88	IRQ7	ISA

17	IRQ6	ISA	89	IRQ9	ISA

18	IRQ5	ISA	90	IRQ10	ISA

19	IRQ4	ISA	91	IRQ11	ISA

20	SA10	ISA	92	SA11	ISA

21	SA9	ISA	93	SA8	ISA

22	SA14	ISA	94	SA13	ISA
23	SA17	ISA	95	SA16	ISA

24	SA12	ISA	96	SA15	ISA

25	IRQ12	ISA	97	IRQ15	ISA

26	SYSCLK	ISA	98	IRQ14	ISA

27	DRQ3	ISA	99	DRQ2	ISA

28	OSC (14 MHz) ISA		100	DRQ5	ISA

29	DRQ1	ISA	101	DRQ6	ISA
30	DRQ0	ISA	102	DRQ7	ISA
31	HDACK	IDE	103	HDDRQ	IDE

32	HDIOW	IDE	104	HDIRQ	IDE

33	LA17	ISA	105	HDIOR	IDE

34	LA19	ISA	106	LA20	ISA

35	LA22	ISA	107	LA18	ISA

4 0 HMI-640S User's Manual

Image 50

Contents HMI-640S Copyright notice Acknowledgments FCC Class a notes Safety Instructions Wichtige Sicherheishinweise Contents Maintenance Networking Communication Figures Page General Information General SpecificationsIntroduction Standard functions CPC-2245NPS/2 keyboard/mouse connector Mini-DIN keyboard connector Ethernet interface Power supplyEnvironmental specifications SVGA/Flat panel interface CPC-2520LCD Specifications TouchscreenCOM2 port settings I/O ArrangementTotal Solution Dimensions Mounting Page System Setup General Packing ListInitial Setup Installing a CompactFlash Memory Card Installing a CompactFlash adapterInstalling a 2.5 HDD Connecting the Power Adapter Installing a PC/104 Module PC/104 module dimensions mm ±5 % Assign the Device Name First System BootPower up for the first time Exploded Diagram Maintenance Removing the Front/Rear Panel Maintenance LCD Display LCD Backlight Power Supply I/O Adapter CPC-2900 Core of HMI-640S CPC-2520/CPC-2245N/ CPC-2430 CPC-2245N Main Board Introduction ISA/IDE/FDD/parallel port 144-pin Sodimm socket Super I/O chipset Winbond W83977FVGA/LAN/serial port/keyboard/mouse 40-pin FPC connector Mechanical and environmentalBoard layout dimensions Jumpers and connectors Name FunctionBoard layout jumper/connector locations Board layout jumper/connector locationsSafety precautions Setting jumpers CompactFlash interface CN2 Clear Cmos J2ISA/IDE/floppy drive/parallel port CN3 Pin Signal Bus SA0 ISA ISA bus CN3GND Rstdrv IRQ9 DRQ2 Memw MEMCS16 Pin Signal IDE interfaceDamping resistor Floppy drive Parallel port 10 VGA/LAN/serial ports/keyboard/ mouse CN4 VGA interface Ethernet configuration Keyboard and PS/2 mouse connectorSerial ports Port Address Default Power supply connector CN5 Card installation Card removal FPC cable installation CPC-2520 VGA/LCD Control Board Introduction Display output Board layout dimensions Number Function Board layout jumper/connector locations Safety precautions Jumper settings Display connectors CN2, CN3 LCD panel select SW1LCD display connector CN2 VGA display connector CN3 Model number of the CN3 socket isVGA CN3 FPC cable installation Page Networking Communica- tion Networking via LAN Connect or disconnect any cableTo assign the IP addresses to your machines, just RAS service, you must install it on your system Networking via RS-232Simple Networking via a Hub Page Cabling for RS-232 Port Pin Null Modem Cable Clear to Send Page DIP Switch Settings Touchscreen Specifications