Advantech HMI-640S user manual GND Rstdrv IRQ9 DRQ2

Page 53

Table 4-5: ISA bus - CN3 cross reference table (ISA bus pin B)

ISA bus		CN3
Pin	Signal	Pin	Signal

B1	GND	9	GND

B2	RSTDRV	75	RSTDRV

B3	+5 V	1	+5 V

B4	IRQ9	89	IRQ9

B5	-5 V	-	-
B6	DRQ2	99	DRQ2
B7	-12 V	-	-

B8	0 WS	2	ZW

B9	+12 V	-	-

B10	GND	10	GND

B11	SMEMW	133	SMEMW

B12	SMEMR	58	SMEMR

B13	IOW	135	IOW
B14	IOR	131	IOR

B15	DACK3	81	DACK3

B16	DRQ3	27	DRQ3

B17	DACK1	83	DACK1

B18	DRQ1	29	DRQ1

B19	REFRESH	63	REFRESH

B20	CLK	26	SYSCLK
B21	IRQ7	88	IRQ7
B22	IRQ6	17	IRQ6

B23	IRQ5	18	IRQ5

B24	IRQ4	19	IRQ4

B25	IRQ3	76	IRQ3

B26	DACK2	82	DACK2

B27	T/C	8	TC

B28	BALE	56	BALE
B29	+5 V	73	+5 V

B30	OSC	28	OSC (14 MHz)

B31	GND	11	GND

Chapter 4 CPC-2245N Main Borad

43

Image 53

Contents HMI-640S Copyright notice Acknowledgments FCC Class a notes Safety Instructions Wichtige Sicherheishinweise Contents Maintenance Networking Communication Figures Page General Information Introduction SpecificationsGeneral Standard functions CPC-2245NPS/2 keyboard/mouse connector Mini-DIN keyboard connector Environmental specifications Power supplyEthernet interface SVGA/Flat panel interface CPC-2520Touchscreen LCD SpecificationsI/O Arrangement COM2 port settingsTotal Solution Dimensions Mounting Page System Setup Packing List GeneralInitial Setup Installing a CompactFlash adapter Installing a CompactFlash Memory CardInstalling a 2.5 HDD Connecting the Power Adapter Installing a PC/104 Module PC/104 module dimensions mm ±5 % Assign the Device Name First System BootPower up for the first time Exploded Diagram Maintenance Removing the Front/Rear Panel Maintenance LCD Display LCD Backlight Power Supply I/O Adapter CPC-2900 Core of HMI-640S CPC-2520/CPC-2245N/ CPC-2430 CPC-2245N Main Board Introduction Super I/O chipset Winbond W83977F ISA/IDE/FDD/parallel port 144-pin Sodimm socketMechanical and environmental VGA/LAN/serial port/keyboard/mouse 40-pin FPC connectorBoard layout dimensions Name Function Jumpers and connectorsBoard layout jumper/connector locations Board layout jumper/connector locationsSafety precautions Setting jumpers Clear Cmos J2 CompactFlash interface CN2ISA/IDE/floppy drive/parallel port CN3 Pin Signal Bus SA0 ISA CN3 ISA busGND Rstdrv IRQ9 DRQ2 Memw MEMCS16 IDE interface Pin SignalDamping resistor Floppy drive Parallel port 10 VGA/LAN/serial ports/keyboard/ mouse CN4 VGA interface Keyboard and PS/2 mouse connector Ethernet configurationSerial ports Port Address Default Power supply connector CN5 Card installation Card removal FPC cable installation CPC-2520 VGA/LCD Control Board Introduction Display output Board layout dimensions Number Function Board layout jumper/connector locations Safety precautions Jumper settings LCD panel select SW1 Display connectors CN2, CN3LCD display connector CN2 Model number of the CN3 socket is VGA display connector CN3VGA CN3 FPC cable installation Page Networking Communica- tion Connect or disconnect any cable Networking via LANTo assign the IP addresses to your machines, just Networking via RS-232 RAS service, you must install it on your systemSimple Networking via a Hub Page Cabling for RS-232 Port Pin Null Modem Cable Clear to Send Page DIP Switch Settings Touchscreen Specifications