Epson 610 manual Interface Specifications, USB Specifications, Configuration, Pin No Signal

Page 11

EPSON Perfection 610

Revision B

1.3 Interface Specifications

This section provides specifications of the USB, the only interface supported by the Perfection 610.

1.3.1 USB Specifications

Any items not included in this specification shall be in compliance with Universal Serial Bus Specification Revision 1.0.

￿Configuration:

See Table 1-2.

Electric specification:

Compliant to Full Speed mode (12Mbit/s) of

 

Universal Serial Bus Specification Revision

 

1.0.

￿Connector:

One Receptacle (Series B)

Connector Pin Assignment: See the following figure.

21

3 4

Figure 1-3. Connector Pin Location

Table 1-1. Connector Pin Assignment

Pin No.

 

Signal

 

 

 

1

 

VCC

 

 

 

2

 

-Data

 

 

 

3

 

+Data

 

 

 

4

 

GND

 

 

 

 

 

 

Table 1-2.

Configuration

 

 

 

 

 

 

 

Element

 

 

 

Description

 

 

 

 

 

 

 

 

 

Class:

Vendor specific

 

 

 

Subclass:

Vendor specific

 

 

 

Protocol:

Vendor specific

 

Device

 

Maximum packet size for endpoint 0:

8byte

 

 

Vendor ID:

0x04B8 (Seiko EPSON Corp.)

 

 

Product ID:

0x0103

 

 

 

Number of possible configurations:

1

 

 

 

 

 

• Number of interfaces supported by this configuration: 1

Configuration

 

Characteristics: Self-powered

 

 

• Remote wake up feature: Not supported

 

 

 

 

• Maximum of possible consumption: 2mA

 

 

No Alternate setting

 

 

 

• Number of endpoints used by

 

Interface

 

 

this interface (excluding endpoint 0):

2

 

Class:

Vendor specific

 

 

 

 

 

 

Subclass:

Vendor specific

 

 

 

Protocol:

Vendor specific

 

 

 

 

 

 

 

Endpoint 1

 

Bulk IN transfer

 

 

 

• Maximum data transfer size: 64 byte

 

 

 

 

Endpoint 2

 

Bulk OUT transfer

 

 

• Maximum data transfer size: 64 byte

 

 

 

 

 

 

 

 

 

 

String

 

iManufacturer:

“EPSON”

 

Descriptor

 

iProduct:

“Scanner GT-6600” or “Perfection610”

 

 

 

 

 

 

Product Description

Interface Specifications

11

Image 11
Contents Epson Perfection Epson Perfection Rev. B Precautions Preface Revision Status Revision Issued Date DescriptionContents Product Description Specifications FeaturesProduct Description Specifications Dimension Pin No Signal Interface SpecificationsUSB Specifications ConfigurationControl Codes Category Command Name CodeControl Codes Lamp DescriptionsCommand Error Error IndicationsManuscript Table Operating Principles Carriage Unit Engine MechanismCarriage Movement Carriage Drive MechanismOutput Over Current Protection Over Voltage Protection Power Supply CircuitSpecification Unit Part No Fuse Protection Circuits for Output Voltages/CurrentsPower Supply Circuit Block Diagram Location Functions Control CircuitMajor ICs Troubleshooting Overview Self-Diagnostic FunctionErrors Detected by the Self-Diagnostic Function Lamp Condition Error Type Cause RemedyCarriage unit does not operate TroubleshootingProblems and Corresponding Tables to Refer to Scanner is not InitializedImage is not read clearly Carriage unit operates but the error is indicatedUSB Interface Error Lamp does not light upAssembly and Disassembly Screws PrecautionsTools Scanner, make sure the carriage is at the home position Disassembly ProceduresWhen locking the carriage for transporting Releasing the Carriage LockDocument Cover Removal Document Cover RemovalUpper Housing Removal Upper Housing RemovalInverter Lamp / Inverter Board Removal Carriage Unit Disassembly10. Inverter Board Removal 12. Metal Clamp Removal Carriage Unit Removal14. Driven Pulley Assembly Removal 16. Timing Belt Removal 19. FFC Metal Clamp and FFC Removal 21. Shield Plate Removal Carriage Motor / Timing Belt Removal24. Timing Belt Removal 26. Main Board Removal Main Board Removal27. Main Board Removal 30. Panel Board Removal Panel Board RemovalBack and forth slowly if necessary Power Supply Board RemovalFollowing steps, manually move the carriage 34. Power Supply Board Adjustment Adjustment Maintenance Lubrication CleaningAppendix Interconnection Connector AssignmentConnector Description Number Refer to Pins Main Board CN5 Power Supply Board CN1Power Supply Board CN102 Main Board CN4Ref. # Description Parts List and Explode DiagramsParts List GT-6600/PERFECTION 610 No.1 Rev.01 Not ASP