Metrologic Instruments MS6130, MX003 manual Appendix D, Warranty and Disclaimer

Page 41

APPENDIX D

Warranty and Disclaimer

Limited Warranty

The MS6130 scanners are manufactured by Metrologic at its Blackwood, New Jersey, U.S.A. facility. The MS6130 scanners have a two (2) year limited warranty from the date of manufacture. Metrologic warrants and represents that all MS6130 scanners are free of all defects in material, workmanship and design, and have been produced and labeled in compliance with all applicable U.S. Federal, state and local laws, regulations and ordinances pertaining to their production and labeling.

This warranty is limited to repair, replacement of Product or refund of Product price at the sole discretion of Metrologic. Faulty equipment must be returned to the Metrologic facility in Blackwood, New Jersey, U.S.A. or Puchheim, Germany. To do this, contact Metrologic’s Customer Service/Repair Department to obtain a Returned Material Authorization (RMA) number.

In the event that it is determined the equipment failure is covered under this warranty, Metrologic shall, at its sole option, repair the Product or replace the Product with a functionally equivalent unit and return such repaired or replaced Product without charge for service or return freight, whether distributor, dealer/reseller, or retail consumer, or refund an amount equal to the original purchase price.

This limited warranty does not extend to any Product which, in the sole judgement of Metrologic, has been subjected to abuse, misuse, neglect, improper installation, or accident, nor any damage due to use or misuse produced from integration of the Product into any mechanical, electrical or computer system. The warranty is void if the case of Product is opened by anyone other than Metrologic’s repair department or authorized repair centers.

THIS LIMITED WARRANTY, EXCEPT AS TO TITLE, IS IN LIEU OF ALL OTHER WARRANTIES OR GUARANTEES, EITHER EXPRESS OR IMPLIED, AND SPECIFICALLY EXCLUDES, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE, OR ARISING OUT OF CUSTOM OR CONDUCT. THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES. IN NO EVENT SHALL METROLOGIC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES TO PERSON OR PROPERTY, OR EFFECT ON BUSINESS OR PROPERTY, OR OTHER DAMAGES OR EXPENSES DUE DIRECTLY OR INDIRECTLY TO THE PRODUCT, EXCEPT AS STATED IN THIS WARRANTY. IN NO EVENT SHALL ANY LIABILITY OF METROLOGIC EXCEED THE ACTUAL AMOUNT PAID TO METROLOGIC FOR THE PRODUCT. METROLOGIC RESERVES THE RIGHT TO MAKE ANY CHANGES TO THE PRODUCT DESCRIBED HEREIN.

North America Headquarters

Metrologic Instruments, Inc.

Customer Service: 1-800-ID-METRO

90 Coles Road

Tel: 856-228-8100

Blackwood, NJ 08012-4683

Email: info@metrologic.com

Germany

Website: www.metrologic.com

 

Metrologic Instruments GmbH

Tel: 49-89-89019-0

Dornierstrasse 2

Fax: 49-89-89019-200

82178 Puchheim b.

Email: info@europe.metrologic.com

Munich, Germany

 

37

Image 41
Contents Metrologic INSTRUMENTS, INC Locations Table of Contents Table of Contents MS6130 Hand Held BAR Code Scanner MX003 Series Scanner Interfaces Receiver Group Unpacking ListTransmitter Group Except version Connections of the Mxnterfacei to the Host DeviceVersion 17 only Connections of the Keyboard Wedge Mxnterfacei to the PCConnections of the MS700I/MS720I With Mxto the Host Device Configuration of the MS700I/MS720I with MX Page Configuration of the Mxto the Scanpal Data Collector Page KB Parameter Keyboard Type Keyboard Wedge KB InterfaceKB Parameter Keyboard Type KB Parameter Caps Lock Mode Microsecond Delay KB Parameter Alt ModeMillisecond Delay Millisecond Delay KB Parameter XT Clean-Up BitConfiguration of the MS6130 HAND-HELD Enabling the MS700I/MS720I SCANNER’S RF LOW Speed Option Handset /X Changing the IDMatching Procedure Output Window Parts of the MS6130 HAND-HELD BAR Code ScannerComponents of the MS6130 Series Stand Installation of the MS6130 Series Stand Permanent Counter TOP Installation Installation of the 6000 Series Universal Charging StandRecommended USE Nicd Battery Charger with Reconditioning FeatureVisual Indicators One Beep Audible IndicatorsRazzberry Tone Two BeepsAudible Indicators Labels MaintenanceTroubleshooting Appendix a SpecificationsMX003 Series Scanner Interface Specifications Temperature Characteristics Degrees Celsius of each Cell Appendix B Default Settings of the MS6130 and MX ReceiverRTS/CTS UPC EAN Parameter Transmitter Default Keyboard Receiver Wedge Pin Function Appendix CMX003 Series Scanner Interface Pin Assignments Appendix D Warranty and DisclaimerAppendix E Patents Appendix FESD IndexTroubleshooting