Brother TD4000, TD4100N manual Responsible Party Brother International Corporation

Page 2

Thank you for purchasing the Brother TD-4000/4100N.

This guide briefly describes the steps to start using the Brother TD-4000/4100N.

See the User's Guide for details. The User's Guide can be found in the Manuals folder of the included CD-ROM.

We strongly recommend that you read this guide carefully before using the Brother TD-4000/4100N, and then keep it nearby for future reference.

We provide service & support for users who register their products on our website. We recommend that you take this opportunity to register with us by visiting us at:

Online User Registration

http://registermybrother.com/

Online Support Page

http://solutions.brother.com/

NOTE: It is also possible to access the above sites from the online user registration window of the included CD-ROM. We look forward to your registration.

Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)

Responsible Party:

Brother International Corporation

 

100 Somerset Corporate Boulevard

 

Bridgewater, NJ 08807-0911 USA

 

TEL: (908) 704-1700

Products Description:

Label Printer

Product Name:

TD-4000/TD-4100N

Model Number:

TD-4000/TD-4100

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Important

The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.

A shielded interface cable should be used in order to ensure compliance with the limits for a Class B digital device.

Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user's authority to operate the equipment.

Image 2
Contents Guía del usuario Responsible Party Brother International Corporation What is not covered What is coveredWhat is the length of the Warranty Periods Who is coveredLimitations What Brother will ask you to doWhat Brother will do Important Information Save Time Register On-LineContents „Compilation and Publication Notice „Symbols Used in this GuideGeneral Information „Trademarks and Copyrights„The Machine Safety Precautions„To use the machine safely „Cutter „Power Cord„Installation/Storage General Precautions „RD Roll„CD-ROM and Software Unpacking the TD-4000/4100N CD-ROM„Rear Parts Description„Front LED Lamp Flow for Creating Labels Connect the Power SupplyInstall the software Print labelsTouch Transfer Express Additional FunctionsPrinting the list of templates Touch TemplateTurn the main power switch on Connecting the Power SupplyCheckoff. that the main power switch is turned Setting the RD Roll „Continuous length label Position the end of the RD roll toTouch the black plastic cutter guard Using Interface Cables USB cable Use the enclosed interface cable RS-232C cableStart the computer and put the CD-ROM into the CD-ROM drive Installing the Software for TD 4000Click Standard Installation Start the software Select a registration method and click NextClick Finish Installing the Software for TD 4100N Utility Installation BRAdmin Light Users GuideNetwork Shared Printer Click OK Then, choose your connection method Click NextLocal Printer with USB cable „For USB interface cable users Click Finish Start the software„For network interface cable users „For shared network printer users Choose your printers queue, and then click OKClick Utility Installation Click BRAdmin Light and follow the on- screen instructionsDouble-click the unconfigured device Uninstalling the Printer Driver Uninstalling Software and Printer DriverUninstalling P-touch Editor Choose Brother XX-XXXX, and click File-Delete Serial Cables Controlling with the ESC/P CommandsAvailable Commands Printing the Printer Settings Turn on the printerMaintenance Troubleshooting Problem SolutionInstalled Is the printer set for sequential printing? „Operating environment Main Specifications„Product specifications „RD Rolls Accessories For USA Only„Paper specification Page Guía del usuario Parte responsable Brother International Corporation Duración de la garantía Quién cubreQué cubre Qué no cubreLimitaciones Qué le pedirá Brother que hagaQué hará Brother Información importante Ahorre tiempo regístrese onlineContenido Procedimientos iniciales„Marcas comerciales y copyright Información general„Compilación y aviso de publicación „Símbolos utilizados en esta guía„La máquina Precauciones de seguridad„Para utilizar la máquina con seguridad „Instalación y almacenamiento „Cable de alimentación„Cortador Precauciones generales „Rollo RD„CD-ROM y software Desembalaje de la TD-4000/4100N Guía del usuario„Vista posterior Descripción de las piezas„Vista frontal Indicador LED Instale el software Flujo de creación de etiquetasConecte la fuente de alimentación Imprima las etiquetasPlantilla de P-touch Funciones adicionalesImpresión de la lista de plantillas Conexión de la alimentación Enciendaprincipal. el interruptor de alimentaciónAjuste del rollo RD „Etiqueta continua Coloque el extremo del rollo RDPara que haga contacto con el Uso de los cables de interfaz ImportanteInstalación estándar Instalación del software de TD-4000Haga clic en Instalación Estándar Mostrar la Guía del usuario Descargar Adobe ReaderInicie el software Seleccione un método de registro y haga clic en SiguienteHaga clic en Finalizar Instalación del software de TD-4100N Instalación personalizada Instalación de la utilidadImpresora compartida de red Impresora local con cable USBImpresora de red punto a punto de Brother „Para usuarios de cable de interfaz USB Haga clic en Finalizar Inicie el software„Para usuarios de cable de interfaz de red „Para usuarios de impresora de red compartida Seleccione la cola de la impresora y haga clic en AceptarHaga clic en Instalación de la utilidad Haga doble clic en el dispositivo sin configuración Desinstalación de P-touch Editor Desinstalación del controlador de la impresoraSeleccione Brother XX-XXXX y haga clic en Archivo-Eliminar Cables serie Control mediante los Comandos ESC/PComandos disponibles Impresión de la configuración de la impresora Encienda la impresoraMantenimiento Corte el rollo RD y extraiga el papel delSolución de problemas Problema SoluciónCompruebe que la ruta de salida de la etiqueta no esté ¿Está la impresora ajustada para la impresión secuencial? „Entorno de funcionamiento Especificaciones principales„Especificaciones del producto „Rollos RD Accesorios para EE.UU. solamente„Especificaciones del papel