Brother TD4000, TD4100N manual Safety Precautions, „To use the machine safely, „The Machine

Page 8

2Introduction

Safety Precautions

Read and understand all of these instructions and save them for later reference. Follow all warnings and instructions marked on the product.

WARNING Tells you what to do to avoid the risk of injury.

CAUTION Tells you about procedures you must follow to prevent damage to the machine.

The symbols used in this guide are as follows:

 

Action NOT allowed to do

 

DO NOT disassemble the product.

 

 

 

 

 

DO NOT splash the product with or

 

DO NOT touch a given portion of the

 

immerse the product in water.

 

product.

 

Mandatory action

 

Unplugging

 

 

 

 

 

Alerts to the possibility of electrical

 

 

 

shock

 

 

„To use the machine safely

WARNING

Follow these guidelines to avoid fire, electric shock, or other damage.

„The Machine

Unplug the power cord immediately and stop using the machine during an electrical storm. There may be a remote risk of electric shock from lightning.

Do not touch any metal parts near the print head. The print head becomes very hot during use and remains very hot immediately after use. Do not touch it directly with your hands.

Dispose of plastic bags correctly and keep away from babies and children. Do not wear or play with plastic bags.

Unplug the power cord immediately and stop using the machine if you notice any abnormal odor, heat, discoloration, deformation or anything unusual whilst the machine is in use or storage.

Do not disassemble the machine.

For inspection, adjustment and repair of the machine contact the retail outlet where the machine was purchased or your local authorized service center.

Do not drop, hit or otherwise bang the machine.

Do not hold and lift the machine by the RD Roll cover. The cover could come off and the machine could fall and become damaged.

Do not allow the machine to get wet in any way.

Do not use the machine with foreign objects in it. If water or any foreign objects should enter the machine, unplug the power cord from the electric outlet and remove the foreign object. If necessary, contact the retail outlet where the machine was purchased or your local authorized service center.

Do not hold the machine with only one hand. The machine may slip out of your hand.

Never disassemble the machine or allow it to get wet to avoid possible fire or electrical shock. Doing so could cause an electrical shock or fire.

Image 8
Contents Guía del usuario Responsible Party Brother International Corporation What is covered What is the length of the Warranty PeriodsWhat is not covered Who is coveredLimitations What Brother will ask you to doWhat Brother will do Important Information Save Time Register On-LineContents „Symbols Used in this Guide General Information„Compilation and Publication Notice „Trademarks and Copyrights„The Machine Safety Precautions„To use the machine safely „Cutter „Power Cord„Installation/Storage General Precautions „RD Roll„CD-ROM and Software Unpacking the TD-4000/4100N CD-ROM„Rear Parts Description„Front LED Lamp Connect the Power Supply Install the softwareFlow for Creating Labels Print labelsAdditional Functions Printing the list of templatesTouch Transfer Express Touch TemplateTurn the main power switch on Connecting the Power SupplyCheckoff. that the main power switch is turned Setting the RD Roll „Continuous length label Position the end of the RD roll toTouch the black plastic cutter guard Using Interface Cables USB cable Use the enclosed interface cable RS-232C cableStart the computer and put the CD-ROM into the CD-ROM drive Installing the Software for TD 4000Click Standard Installation Start the software Select a registration method and click NextClick Finish Installing the Software for TD 4100N Utility Installation BRAdmin Light Users GuideNetwork Shared Printer Click OK Then, choose your connection method Click NextLocal Printer with USB cable „For USB interface cable users Click Finish Start the software„For network interface cable users „For shared network printer users Choose your printers queue, and then click OKClick Utility Installation Click BRAdmin Light and follow the on- screen instructionsDouble-click the unconfigured device Uninstalling the Printer Driver Uninstalling Software and Printer DriverUninstalling P-touch Editor Choose Brother XX-XXXX, and click File-Delete Serial Cables Controlling with the ESC/P CommandsAvailable Commands Printing the Printer Settings Turn on the printerMaintenance Troubleshooting Problem SolutionInstalled Is the printer set for sequential printing? „Operating environment Main Specifications„Product specifications „RD Rolls Accessories For USA Only„Paper specification Page Guía del usuario Parte responsable Brother International Corporation Quién cubre Qué cubreDuración de la garantía Qué no cubreLimitaciones Qué le pedirá Brother que hagaQué hará Brother Información importante Ahorre tiempo regístrese onlineContenido Procedimientos inicialesInformación general „Compilación y aviso de publicación„Marcas comerciales y copyright „Símbolos utilizados en esta guía„La máquina Precauciones de seguridad„Para utilizar la máquina con seguridad „Instalación y almacenamiento „Cable de alimentación„Cortador Precauciones generales „Rollo RD„CD-ROM y software Desembalaje de la TD-4000/4100N Guía del usuario„Vista posterior Descripción de las piezas„Vista frontal Indicador LED Flujo de creación de etiquetas Conecte la fuente de alimentaciónInstale el software Imprima las etiquetasPlantilla de P-touch Funciones adicionalesImpresión de la lista de plantillas Conexión de la alimentación Enciendaprincipal. el interruptor de alimentaciónAjuste del rollo RD „Etiqueta continua Coloque el extremo del rollo RDPara que haga contacto con el Uso de los cables de interfaz ImportanteInstalación del software de TD-4000 Haga clic en Instalación EstándarInstalación estándar Mostrar la Guía del usuario Descargar Adobe ReaderInicie el software Seleccione un método de registro y haga clic en SiguienteHaga clic en Finalizar Instalación del software de TD-4100N Instalación personalizada Instalación de la utilidadImpresora compartida de red Impresora local con cable USBImpresora de red punto a punto de Brother „Para usuarios de cable de interfaz USB Haga clic en Finalizar Inicie el software„Para usuarios de cable de interfaz de red „Para usuarios de impresora de red compartida Seleccione la cola de la impresora y haga clic en AceptarHaga clic en Instalación de la utilidad Haga doble clic en el dispositivo sin configuración Desinstalación de P-touch Editor Desinstalación del controlador de la impresoraSeleccione Brother XX-XXXX y haga clic en Archivo-Eliminar Cables serie Control mediante los Comandos ESC/PComandos disponibles Impresión de la configuración de la impresora Encienda la impresoraMantenimiento Corte el rollo RD y extraiga el papel delSolución de problemas Problema SoluciónCompruebe que la ruta de salida de la etiqueta no esté ¿Está la impresora ajustada para la impresión secuencial? „Entorno de funcionamiento Especificaciones principales„Especificaciones del producto „Rollos RD Accesorios para EE.UU. solamente„Especificaciones del papel