Fujitsu SRS-9924 manual To Make a Call

Page 114

SRS-9912-SP and SRS-9924

QUICK REFERENCE CARD

To Make a Call

1.Press idle CA (Call Appearance) and pick up the handset. (For handsfree mode, press SPEAKER.)

2.Dial the number.

To Place One-Touch Calls

Press a one-touch button. (If no idle CA LED lights, press any idle CA.)

To Answer a Call

1.Press the green-flashing CA.

2.Pick up the handset. (For handsfree mode, press SPEAKER.)

To Put a Call on HOLD

1.Press HOLD.

2.To get a dial tone, press an idle CA; to connect with another call press a lit or blinking CA.

3.To reconnect with call on hold, press its CA.

To Set Up a CONFERENCE Call

1.While on an active call, press CONFERENCE.

2.Another CA/DN will be selected automatically and you will hear the dial tone.

3.Dial the third party.

OR

4.Press any CA/DN that is ringing or on HOLD.

5.Press CONFERENCE.

Repeat steps 1-3 to add more calls. To disconnect last call added, press DROP. Other participants can drop out by hanging up. At some installations if you drop out, the entire conference is disconnected. Ask your Systems Administrator.

To Use Call Pickup

1.Get a dial tone.

2.Press CALL PICKUP feature button.

To Review Unanswered Call List (UNA)

1.When a •UNA appears on the displays, press UNA (softkey 1). Information from the oldest unanswered call appears.

2.Press UNA again. Information from the next-to-oldest unanswered call appears. After displaying most recent call, display returns to the oldest call.

3.To delete displayed call information, press # on the keypad, then CLEAR (softkey 3).

To Use Personal Directory

1.Press L-DIR.

2.Scroll to the name and number you want to call, using the * key to scroll up and the # to scroll down. The > should be next to the Name you want to call.

You may also dial the two-digit code (e.g. 02) associated with the name or number.

3.Lift the handset or press the speaker button.

To Switch To/From Handsfree

To switch to handsfree, press SPEAKER and replace handset in cradle. (The MIC-OFF button must be turned off to talk; if its LED is lit, press it once to turn it off.)

To switch to handset, pick up handset.

To Change Call Volume

With a CA active (LED on), pressrepeatedly to increase volume, pressrepeatedly to decrease volume. Volume is held until reset.

To Adjust Display (When No Call is Active)

Press repeatedly to increase contrast.

Press repeatedly to decrease contrast.

To Use MIC-OFF

To mute handset or the handsfree microphone, press MIC-OFF (LED lights). Press again to turn microphone on (LED goes dark).

To Program a One-Touch Button

1.Press OPTIONS (softkey 4), 1 on the keypad, then ENTER (softkey 1).

2.Press the button you want to make a one-touch. (Do not reuse CA FA keys. Or press an existing one-touch button to change its recorded number.)

3.Dial the numbers you want that button to send.*

4.Press ENTER. (COMPLETED appears on display.)

5.To exit, press OPTIONS.

*Use the HOLD button to insert pauses.

Page 113 Page 115
Image 114
Page 113 Page 115
Contents Page Terminal Installation Terminal Accessories Terminal Intro & Table of ContentsTerminal Overview Using Terminal Set-Up SRS-9924-ABM Appendix Terminal TestingFujitsu NI / 5E Custom Terminal Intro & Table of Contents Fujitsu NI 5E Custom Terminal Intro Table of Contents Mfgrs Port Facilities Service Order Network Jack HOW to USE this Guide Conventions and Layout DMS-100Ewsd DIR Isdn Concepts Spid Table of Contents Appendix a Testing Appendix B Appendix CAppendix D NI / 5E Custom Terminal Overview SRS-9924 National Isdn Front Panel5E Custom Terminal Overview SRS-9924 5E Custom Front PanelSRS-9912-SP National Isdn Front View Overview SRS-9912-SP 5E Custom National Isdn Front ViewRear stand Unique Components Switches Connectors LED Indicators NI utilizes Feature Activators 19 or MIC-OFF Button Function Keys Permanent FunctionsFunction Button Layout For Multifunction Keys Multifunction ButtonsNI / 5E Custom Terminal Example Line Assignment SRS-9924Softkeys and Menu NI only5E Custom only UNAUsing the Terminal 5E Custom onlyLine Parameters Using Terminal Autohold OnetouchSRS-9924 and SRS-9912-SP are equipped with Using the Terminal Receiving Handsfree Calls Placing Headset Calls 5E Custom If you are using the handset and want to use handsfree modeOnly MethodFunction Isdn Redial Dropping Out Conference Call Transfer Transfer DMS-100, NI1 ONE-TOUCH Calling Using Terminal UNA DIR UNA-LIST Personal DirectoryUsing the NI / 5E Custom Terminal Set-UpStandard Softkey Layout Menu Option Options at any time, as follows Using 5E Custom Terminal Set -UpSelecting a 5E Custom only NI onlyUsing the NI / 5E Custom Terminal Set-Up Programming a One-Touch ButtonNumbers you program can be any of the following Enter Directory Number Correct number Mode main menu, press asteriskAssociated LED turns green, and the word Multifunction button again. The Enter4 7 6 2 9 , 9 9 , , 2 5 0 Enter Directory Number Setting the Calendar /CLOCK Enter the present date 1 to 31 and then press To return to normal operation, press Options Enabling the UNA FeatureTerminal Set -Up To leave it as is, press Options againNI / 5E Custom Terminal Set-Up To support UNA on all CAs, follow these stepsIf the following screen appears, the feature is enabled Options 4 EnterThis feature enables and disables the speakerphone function Headset Mode Handset Mode Handsfree SupportedUsing the Handset or a Headset Press ENTER, and this screen appearsSetting Ringer Tone Selecting Ringer Pattern Mode Selecting Ringer PatternLeased Network Access CodeAssigning a DelimiterTurns green. The number of the new button Goes off and the indicator of the new buttonAs the delimiter key. Its indicator goes out Appears on the displayRinger Always On Call Announce Intercom on Selected Buttons Specifying the Directory Number for Intercom Select from the followingEnter the following appears TWO WAY Turned on Example 919 926-3112 or Example 919*926*3112 Screen should now appear as followsPress Options to return to standard display NI only Repeat steps 2 and 3 until this screen appearsPreference options determine which CA Selecting CA Preference Press the desired preference number, thenMIC-OFF 5E Custom only Editing Personal MenuPress Enter to display this screen Press Exit to return to the initial screenDirectory Full will be displayed. Using NetworkData DigitsUsing the NI / 5E Custom SRS-9924-ABM ChapterSRS 9924 ABM 5E Custom ABM Button AssignmentsSRS-9924-ABM Bottom View 5E Custom SRS-9924-ABM Chapter Installation 5ESSTerminal Installation Installing the Isdn equipment may be installed in a numberSETTING-UP Spids Manually cleared Auto-SPID displays the following screens When the is indicating the correct SpidAuto-SPID This screen is displayedDial your voice Spid number and press Enter 5E Custom Terminal Installation Configuration Types Ekts Cach Loading orModifying Network Data after entering the Spid Key Attribute Configuration Download Numbers with options 1 and 2 of KEY-ATTRManual Configuration Press 2 to display the options for manual downloadSelection Call Appearance Cach Call Buttons Secondary or shared Telephone NumberAre always distinctive If you press an unlit button, the screen looks like this CA=XXXX CompletedSet’s indicators show button status as follows If you select an unlit button, the screen looks like this You now have two choicesThis completes programming of FAs. If you CA setting. Then you can enter DNsFactory default CA=1 ProviderDirectory Number Mode DN=XX This returns you to the menu mode main menu Selection Intercom/Group Final screen looks like thisSelection Conference Press selected Conf button. This screen appearsPress ENTER. The selected button’s LED turns green Selection 7 Originating DN Completed Select Assign KEY Invalid SelectionPress the selected Multi-assign key Orgip = TRM =ORG = OFF =Selection Designated Call Appearance SRS-9924 Distance between the NT1 and the terminal is up to 230 ft Single Unit Installations Two Unit InstallationsAccessories NI / 5E Custom Terminal Accessories5E Custom Terminal Accessories Handset FeaturesTerminal mount, and two screws hold Wall Kit Terminal is attached to the wall byIllustration. Three screws hold Optional ABM mountTo replace the cartridge ROM CartridgeTerminal Remove the screw holding the cartridgeEntering Test Mode Appendix a TestingNI / 5E Custom Appendix Terminal Testing When the LED test is complete, this screen appears2SOFT2 PerformingTests 3SOFT3 4SOFT4Conf Function KEYFunction KEY Hold Function KEY Redial SpeakerExiting Test Mode Its place if different errors are discoveredTo be handled by your System Administrator Memory Tests Pressing 4 on the numeric keypad starts anAppendix B NI / 5E Custom Appendix Error MessagesError Messages No RouteUnspecified DiscardedNot Available Facility N/ANON-EXISTENT or not Element ContentsReference Value ImplementedCall is Proceeding ProceedingThreshold Exceeded Undefined Code Service DeniedAnnouncement UnassignedTable B-4 Uniform Cause Values Cause # Message Displayed Appendix C Ordering National Isdn Lines NI / 5E Custom Appendix Ordering National Isdn LinesConfiguration listed below. Following Using IOCsLines and features Select that solution packageMSG CFD/CFBCFV CNIIsdn Conference Button/FA = Drop Button/FA Transfer Button/FA =Call Forwarding Variable FA = Appendix 5E Custom Terminal ICI Displays Appendix 5E Custom Terminal ICI Displays NI only To Make a Call Custom Commands for NI System only To Transfer a Call

SRS-9924 specifications

The Fujitsu SRS-9924 is a cutting-edge solution designed for high-performance computing, data storage, and advanced networking applications. This advanced system is centered on versatility, robustness, and efficiency, catering to diverse industry needs including data centers, telecommunications, and enterprise environments.

One of the key features of the SRS-9924 is its scalable architecture. It supports a wide range of configurations, allowing organizations to tailor the system to their specific requirements. This scalability ensures that as data demands grow, the SRS-9924 can adapt seamlessly with additional resources, making it future-proof for growing enterprises.

The SRS-9924 incorporates state-of-the-art processing power, with multi-core processors that enhance computational capabilities while improving energy efficiency. This is complemented by high-speed memory options, which optimize performance for demanding applications. As a result, users experience significantly faster data processing times, which is critical for applications such as real-time analytics and high-frequency trading.

Another notable technology in the SRS-9924 is its advanced networking capabilities. Equipped with robust connectivity options, it supports multiple protocols and architectures, allowing seamless integration into existing IT infrastructures. The system features high-bandwidth options that ensure rapid data transfer and lower latency, which is crucial for applications that rely on speed and reliability.

The Fujitsu SRS-9924 also prioritizes data protection and security. With sophisticated redundancy features and error-checking technologies, the system minimizes data loss risks and enhances reliability. This is particularly important in industries such as finance and healthcare, where data integrity is paramount.

Power management is another area where the SRS-9924 excels. Fujitsu has implemented innovative energy-saving features that not only reduce operational costs but also align with global sustainability goals. This focus on efficiency helps organizations achieve their green IT objectives without compromising on performance.

In summary, the Fujitsu SRS-9924 stands out as a versatile and powerful solution for modern computing challenges. With its scalable architecture, advanced processing and networking capabilities, enhanced security measures, and energy-efficient design, it is well-suited for organizations looking to leverage technology for competitive advantage in today’s data-driven landscape.
Top Page Image Contents