Fujitsu SRS-9924 manual MIC-OFF 5E Custom only

Page 61

MIC-OFF

5E CUSTOM ONLY

If you deactivate MIC-OFF, assign the upper right button as a one-touch button, and then try to reactivate MIC-OFF, the button’s LED turns red as a warning. You must quit the procedure (press * to return to the menu mode main menus) and cancel the one-touch number before you can reactivate MIC-OFF.

If you try to reactivate MIC-OFF without doing this, the message INVALID SELECTION appears and your attempt fails.

If you are deactivating the MIC-OFF button, make sure the function is turned off (the LED is unlit) before beginning the procedure.

This is option 11 in the 5E Custom OPTIONS Menu, but the later steps to deactivate MIC OFF are the same.

1.

OPTIONS

12

ENTER

MIC-OFF KEY MODE

NON SUPPORTED

2.ENTER

1:SUPPORT 2: NO SUPPORT (SELECT 1-2)

The LED in the upper right button indicates its current state:

• Off: Unassigned

•Green: Active as MIC-OFF

•Red: Assigned as a one-touch button

If you wish to reactivate MIC-OFF, you must first cancel the one-touch assignment on the upper right button.

3.Press 1, then ENTER to activate MIC-OFF Or Press 2, then ENTER to deactivate MIC-OFF:

SUPPORTED

COMPLETED

3

Using the NI / 5E Custom Terminal Set-Up

3-25

Image 61

Contents Page Terminal Overview Using Terminal Set-Up SRS-9924-ABM Terminal Intro & Table of ContentsTerminal Installation Terminal Accessories Appendix Terminal TestingFujitsu NI / 5E Custom Terminal Intro & Table of Contents Fujitsu NI 5E Custom Terminal Intro Table of Contents Mfgrs Port Facilities Service Order Network Jack HOW to USE this Guide DMS-100 Conventions and LayoutEwsd DIR Isdn Concepts Spid Table of Contents Appendix C Appendix a Testing Appendix BAppendix D SRS-9924 National Isdn Front Panel NI / 5E Custom Terminal OverviewSRS-9924 5E Custom Front Panel 5E Custom Terminal OverviewSRS-9912-SP National Isdn Front View SRS-9912-SP 5E Custom National Isdn Front View OverviewRear stand Unique Components Switches Connectors LED Indicators MIC-OFF Button Function Keys Permanent Functions NI utilizes Feature Activators 19 orFunction Button Layout For Multifunction Keys Buttons MultifunctionExample Line Assignment SRS-9924 NI / 5E Custom Terminal5E Custom only NI onlySoftkeys and Menu UNA5E Custom only Using the TerminalLine Parameters Autohold Onetouch Using TerminalSRS-9924 and SRS-9912-SP are equipped with Using the Terminal Receiving Handsfree Calls Placing Headset Calls Only If you are using the handset and want to use handsfree mode5E Custom MethodFunction Isdn Redial Dropping Out Conference Call Transfer Transfer DMS-100, NI1 ONE-TOUCH Calling Using Terminal UNA UNA-LIST Personal Directory DIRSet-Up Using the NI / 5E Custom TerminalStandard Softkey Layout Selecting a Using 5E Custom Terminal Set -UpMenu Option Options at any time, as follows 5E Custom only NI onlyProgramming a One-Touch Button Using the NI / 5E Custom Terminal Set-UpNumbers you program can be any of the following Enter Directory Number Associated LED turns green, and the word Mode main menu, press asteriskCorrect number Multifunction button again. The Enter4 7 6 2 9 , 9 9 , , 2 5 0 Enter Directory Number Setting the Calendar /CLOCK Enter the present date 1 to 31 and then press Terminal Set -Up Enabling the UNA FeatureTo return to normal operation, press Options To leave it as is, press Options againTo support UNA on all CAs, follow these steps NI / 5E Custom Terminal Set-UpOptions 4 Enter If the following screen appears, the feature is enabledHeadset Mode Handset Mode Handsfree Supported This feature enables and disables the speakerphone functionPress ENTER, and this screen appears Using the Handset or a HeadsetSetting Ringer Tone Selecting Ringer Pattern Selecting Ringer Pattern ModeAssigning a Access CodeLeased Network DelimiterAs the delimiter key. Its indicator goes out Goes off and the indicator of the new buttonTurns green. The number of the new button Appears on the displayRinger Always On Call Announce Intercom on Selected Buttons Select from the following Specifying the Directory Number for IntercomEnter the following appears TWO WAY Turned on Example 919*926*3112 Screen should now appear as follows Example 919 926-3112 or Press Options to return to standard display Repeat steps 2 and 3 until this screen appears NI onlyPreference options determine which CA Press the desired preference number, then Selecting CA PreferenceMIC-OFF 5E Custom only Menu Editing PersonalPress Exit to return to the initial screen Press Enter to display this screenData Using NetworkDirectory Full will be displayed. DigitsChapter Using the NI / 5E Custom SRS-9924-ABMAssignments SRS 9924 ABM 5E Custom ABM ButtonSRS-9924-ABM Bottom View 5E Custom SRS-9924-ABM 5ESS Chapter InstallationInstalling the Isdn equipment may be installed in a number Terminal InstallationSETTING-UP Spids Auto-SPID When the is indicating the correct SpidManually cleared Auto-SPID displays the following screens This screen is displayedDial your voice Spid number and press Enter 5E Custom Terminal Installation Loading or Configuration Types Ekts CachModifying Network Data after entering the Spid Numbers with options 1 and 2 of KEY-ATTR Key Attribute Configuration DownloadPress 2 to display the options for manual download Manual ConfigurationSecondary or shared Telephone Number Selection Call Appearance Cach Call ButtonsAre always distinctive CA=XXXX Completed If you press an unlit button, the screen looks like thisSet’s indicators show button status as follows You now have two choices If you select an unlit button, the screen looks like thisFactory default CA=1 CA setting. Then you can enter DNsThis completes programming of FAs. If you ProviderDirectory Number Mode DN=XX Selection Intercom/Group Final screen looks like this This returns you to the menu mode main menuPress selected Conf button. This screen appears Selection ConferencePress ENTER. The selected button’s LED turns green Completed Select Assign KEY Invalid Selection Selection 7 Originating DNPress the selected Multi-assign key ORG = TRM =Orgip = OFF =Selection Designated Call Appearance SRS-9924 Distance between the NT1 and the terminal is up to 230 ft Two Unit Installations Single Unit InstallationsNI / 5E Custom Terminal Accessories AccessoriesHandset Features 5E Custom Terminal AccessoriesIllustration. Three screws hold Wall Kit Terminal is attached to the wall byTerminal mount, and two screws hold Optional ABM mountTerminal ROM CartridgeTo replace the cartridge Remove the screw holding the cartridgeNI / 5E Custom Appendix Terminal Testing Appendix a TestingEntering Test Mode When the LED test is complete, this screen appearsTests Performing2SOFT2 3SOFT3 4SOFT4Function KEY Hold Function KEYConf Function KEY Redial SpeakerTo be handled by your System Administrator Its place if different errors are discoveredExiting Test Mode Memory Tests Pressing 4 on the numeric keypad starts anError Messages NI / 5E Custom Appendix Error MessagesAppendix B No RouteNot Available DiscardedUnspecified Facility N/AReference Value Element ContentsNON-EXISTENT or not ImplementedProceeding Call is ProceedingThreshold Exceeded Announcement Service DeniedUndefined Code UnassignedTable B-4 Uniform Cause Values Cause # Message Displayed NI / 5E Custom Appendix Ordering National Isdn Lines Appendix C Ordering National Isdn LinesLines and features Using IOCsConfiguration listed below. Following Select that solution packageCFV CFD/CFBMSG CNIConference Button/FA = Drop Button/FA Transfer Button/FA = IsdnCall Forwarding Variable FA = Appendix 5E Custom Terminal ICI Displays Appendix 5E Custom Terminal ICI Displays NI only To Make a Call To Transfer a Call Custom Commands for NI System only