Linksys USB100TX manual Network Neighborhood, I can only see some of the computers

Page 20

Linksys EtherFast® Series

5.In Network Neighborhood I can see myself but no other computers.

•Make sure that the cables are connected correctly. Make sure you are get- ting Link or Activity lights on both the USB Network Adapter and your hub if you are using one. Try changing to a new cable that you know is working.

•Ensure that the other PC is turned on!

6.I’ve decided that I don’t want to share a drive or printer anymore, or I have decided to physically remove a drive or printer from my network.

•You’re going to have to manually reconfigure your File and Printer Sharing settings. To do so, double-click on your My Computer icon. Click on the Printers folder. A window of available printers will appear. Using your right mouse button, click once on the printer that you want to disable on the network. Click on Sharing, followed by the Sharing tab. Click on Not Shared. When you're done, click on the Apply button, fol- lowed by OK.

•You can disable shared drives in the same way. In Windows Explorer, right-click on the drive you want to stop sharing. Click on Sharing, fol- lowed by the Sharing tab. Click on Not Shared. When you're done, click on the Apply button, followed by OK.

7.In Network Neighborhood, you can only see computers running the same operating system as you. For example, if you are running Windows 98, you can see other Windows 98 computers but not any Windows 95 computers.

•Click Start, Find, then Computer and type the name of any other com- puter in the window that comes up. Click Find Now.

•Make sure that you are using the same protocols and workgroup names on the computers. To do this, click on Start, Settings, Control Panel, then double-click on the Network icon. Click on the Configuration tab and verify your protocol settings. If any protocols are missing, add any needed protocol(s) using the Add button in the Network window. Next, click on the Identification tab for Workgroup settings. Make sure they are consistent with your other PCs.

•If all computers are using the same protocol(s) and Workgroup name, and Windows 95 computers can't see Windows 98 computers, enable NetBIOS on all the computers using Windows 95 and 98.

•IPX/SPX-compatible Protocol should be installed on all computers.

•Bring up the properties of the IPX/SPX-compatible Protocol. To do this, click on Start, Settings, Control Panel, then open Network and click on the Configuration tab. Highlight IPX/SPX-compatible Protocol (only one of them) and click on Properties.

10/100 USB Network Adapter

•Click on the NetBIOS tab. Put a check next to I want to enable NetBIOS over IPX/SPX and click OK. Click OK again.

•After Windows finishes copying the appropriate files, restart your com- puter. When you’ve returned to the desktop, open Network Neighborhood or my network places and look for the other PCs on your network.

8.In Network Neighborhood, I can only see some of the computers.

•Choose Start, Find, Computer and type the name of the computer in the window that comes up and click Find Now.

•Now make sure that the you are using the same protocol(s) and work- group name on computers. To do this, click Start, Settings, Control Panel on two computers running different Windows operating systems. Click on the Network icon, choose the Configuration tab, then click on the Identification tab for Workgroup name. Compare the protocols on both computers and make sure that they are the same. If any protocols are missing, refer to the Manually Installing Network components in Windows 98 section on page 43 to install any needed protocol(s).

•Ensure that File & Print sharing is enabled on every computer.

9.Network Neighborhood is empty.

•Verify that your Microsoft Client is installed. See the Windows 98 setup instructions in this guide for directions.

•Verify that you have logged in correctly. Refresh the screen by pressing F5 several times.

10.The LEDs on the adapter flash back and forth in rhythm.

•The driver for the EtherFast 10/100 USB Network Adapter has not been properly installed. You must re-install the drivers.

11.On some notebook PCs, the EtherFast 10/100 USB Network Adapter fails to configure correctly after the drivers have been loaded.

•After loading the software drivers, it may be necessary to do the follow- ing:

1.Log off and unplug the device from your PC’s USB port.

2.Turn off your PC.

3.Plug the device back in and reboot.

4.Log on after the PC reboots.

33

34

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 10/100 USB Network Adapter Copyright & Trademarks Table of Contents Features IntroductionEtherFast 10/100 USB Network Adapter Windows & Computer CompatibilityAdapter’s Ports LAN 10/100Adapter’s LEDs USB IconOverview Installing the USB Network Adapter & CabUSB Cabling Connecting to an Ethernet or Fast Ethenet Network Installing the USB Network Adapter’s DriverUnder no circumstance are you to click Cancel or Skip File Network Component Configuration TCP/IPTo allow others to print to my printer Linksys EtherFast Series Sharing Your Files and Printers in Windows OverviewEnabling File Sharing Enabling Printer SharingWindows Millennium Installation & Setup Uration or troubleshooting Linksys EtherFast Series 10/100 USB Network Adapter \windows\options\cabs Sharing Your Files and Printers in Windows Windows 2000 Installation & Setup Installing the Network Adapter’s DriverTroubleshooting LEDs on the adapter flash back and forth in rhythm Network Neighborhood, I can only see some of the computersNetwork Neighborhood is empty Appendix Client for Microsoft Setup for WindowsNovell NetWare 3.x Client Setup for Windows Starting Over in Windows Linksys EtherFast Series Starting Over in Windows Manually Installing Network Components in Windows Linux, Open Source and Beta Operating SystemsTwisted-Pair Cabling SpeciCrimping Your Own Network Cables Straight-Through Cabling Cross-Over CablingSpecifications Linksys Warranty InformationEnvironmental Customer SupportCopyright 2001 Linksys, All Rights Reserved
Top Page Image Contents