Linksys WAP2000 manual Wireless Vlan & QoS

Page 17

Chapter 5

Advanced Configuration

Access Point address, the Broadcast destination addresses, a time stamp, Delivery Traffic Indicator Maps, and the Traffic Indicator Message (TIM). The default is 100 ms.

DTIM Interval  This value indicates how often the Access Point sends out a Delivery Traffic Indication Message (DTIM). Lower settings result in more efficient networking, while preventing your PC from dropping into power- saving sleep mode. Higher settings allow your PC to enter sleep mode, thus saving power, but interferes with wireless transmissions. The default is 1 ms.

RTS Threshold  Thissettingdetermineshowlargeapacket can be before the Access Point coordinates transmission and reception to ensure efficient communication. This value should remain at its default setting of 2347. If you encounter inconsistent data flow, only minor modifications are recommended.

Fragmentation Threshold  This specifies the maximum size a data packet can be before splitting and creating a new packet. It should remain at its default setting of 2346. A smaller setting means smaller packets, which will create more packets for each transmission. If you experience high packet error rates, you can decrease this value, but it will likely decrease overall network performance. Only minor modifications of this value are recommended.

Change these settings as described here and click Apply to save your changes. Help information is available on the right side of the screen.

Wireless > VLAN & QoS

This screen allows you to configure the VLAN and QoS related settings for the Access Point.

Wireless > VLAN & QoS

VLAN  Select Enabled if you want to pass 802.1q VLAN tagged traffic between the wired LAN and wireless LAN. Your Access Point will map the VLAN tag (wired side) to different SSIDs (wireless side) according to your specified settings. Select Disabled and your Access Point will drop all

tagged traffic coming in from the wired LAN. The default is Disabled.

Default VLAN ID  Enter the default VLAN ID number (1

-4094), the default value is 1. The default VLAN number should match with your Switch’s settings. For example, the SRW2024 has Trunk port mode which set default VLAN (PVID) to 1 untagged, while General port mode can set PVID to any VLAN either tagged or untagged.

Default VLAN  Set the tagging option for the default VLAN ID. This has to match your Switch’s settings. The default is untagged.

ManagementVLAN ID  When theVLAN option is enabled, the value entered (VLAN ID) in this field defines the VLAN that connects to the Access Point. The default value is 1. The VLAN should be accessible from the wired side in order to use web-based utility. To access the web‑based utility from wireless side, the SSID needs to map to the same VLAN ID. Remember to enable wireless web access on the Administration > Management tab.

The following options are VLAN global settings for the Access Point.

Default CoS (Priority)  Select Enabled if you want to assign a default CoS value to each SSID. This option is automatically enabled when the VLAN option is enabled. The default is Disabled.

U-APSD (Unscheduled Automatic Power Save Delivery)  This option is only available when WMM is enabled on any of the SSIDs. Select Enabled if you want client devices with U-APSD capability to take advantage of the power save mode. The default is Disabled.

SSID Name  Displays the SSIDs defined on the Basic Wireless Settings screen. If an SSID has been disabled, the options cannot be configured.

VLAN ID  Select a VLAN ID (1 - 4094) for the SSID where you want to map the traffic to on the wired side. The wireless traffic will not carry VLAN information. Multiple SSIDs can map to the same VLAN on the wired side.

Priority  You can assign the default priority (802.1p CoS bits) for packets coming in from each wireless network by selecting a value from the drop-down menu. The default is Low.

Tx Rate Limitation  You can limit the maximum data rate used in your network to save bandwidth and power consumption on client devices. The actual data rate is determined by the Auto-Fallback mechanism between your Access Point and a client device. The default is 54 Mbps.

WMM  Wi-Fi Multimedia is a QoS feature defined by the WiFi Alliance before IEEE 802.11e was finalized. Now it is part of IEEE 802.11e. When this is enabled, it provides four

Wireless-G Access Point with Power Over Ethernet

13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Wireless-G Access Point with Power Over Ethernet About This Guide About This GuideTable of Contents Appendix G Contact Information Chapter Introduction ChapterNetwork Topology Chapter Planning Your Wireless NetworkRoaming Network LayoutProduct Overview Chapter Product OverviewFront Panel Back PanelInstallation Chapter InstallationPlacement Wall-MountConnecting the Access Point Advanced Configuration Chapter Advanced ConfigurationAccessing the Web-Based Utility Setup SetupWireless Basic Wireless Settings Setup TimeWEP Wireless Wireless SecurityWPA2-Personal WPA-Personal aka WPA-PSKWPA2-Enterprise WPA2-Personal MixedWPA-Enterprise WPA2-Enterprise Mixed DisableWireless Advanced Wireless Settings Wireless Wireless Connection ControlWireless Vlan & QoS Administration Management AP ModeLog Administration LogAdministration Reboot Administration Factory DefaultAdministration Firmware Upgrade Status Local Network Administration Configuration ManagementWired Status WirelessWireless Status System PerformanceChapter Appendix a Appendix a TroubleshootingTroubleshooting Troubleshooting Does the Access Point function as a firewall? Wireless Security Checklist Appendix B Wireless Security ChecklistAppendix B General Network Security GuidelinesGlossary Appendix CAppendix C Glossary Glossary Smtp Simple Mail Transfer Protocol The standard Appendix C Appendix D Appendix D SpecificationsSpecifications Appendix E Warranty InformationLimited Warranty Regulatory Information Appendix FAvis d’Industrie Canada Wireless DisclaimerDansk Danish Miljøinformation for kunder i EU Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Contact Information Appendix G

WAP2000 specifications

The Linksys WAP2000 is a robust wireless access point designed to enhance connectivity for both home and small business environments. This device provides a reliable solution for extending the reach of your existing network, ensuring that users can access high-speed internet with minimal interruptions.

One of the main features of the Linksys WAP2000 is its dual-band capability, which operates on both the 2.4 GHz and 5 GHz frequency bands. This dual-band technology allows for greater flexibility and less interference, accommodating more devices while maintaining optimal performance. Users can connect to the 5 GHz band for bandwidth-intensive activities, such as streaming and online gaming, while the 2.4 GHz band serves well for general browsing and connecting older devices.

The WAP2000 is equipped with the latest 802.11n wireless standard, offering speeds of up to 300 Mbps. This high throughput makes it an efficient choice for businesses that require swift data transfers and reliable connections. Additionally, the device supports Multiple Input Multiple Output (MIMO) technology, which uses multiple antennas to send and receive more data simultaneously, further enhancing its performance and range.

For ease of installation, the Linksys WAP2000 features Power over Ethernet (PoE) support. This allows the device to receive power through the Ethernet cable, eliminating the need for separate power adapters and simplifying the setup process. Additionally, its browser-based setup utility provides a user-friendly interface for configuration, enabling users to customize settings easily.

Security is a critical concern for any network, and the Linksys WAP2000 addresses this with various security features. It supports WPA/WPA2 encryption protocols, protecting data transmitted over the network from unauthorized access. Furthermore, the device includes MAC address filtering, which allows users to control which devices can connect to the network.

With a sturdy design and compact form factor, the Linksys WAP2000 is suitable for a variety of deployment scenarios, whether mounted on walls or placed on desks. Its versatility and performance make it an excellent choice for users looking to improve their wireless connectivity, ensuring that both guests and employees can enjoy a seamless online experience. Overall, the Linksys WAP2000 is an essential addition to any network, providing high-speed internet access and robust security features to keep users connected and safe.
Top Page Image Contents