Linksys WAP2000 manual Appendix C Glossary

Page 28

Appendix C

Appendix C:

Glossary

This glossary contains some basic networking terms you may come across when using this product.

WEB: For additional terms, please visit the

glossary at www.linksys.com/glossary

Access Mode  Specifies the method by which user access is granted to the system.

Access Point  A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.

Access Profiles  Allows network managers to define profiles and rules for accessing the device. Access to management functions can be limited to user groups, which are defined by the following criteria:

Ingress interfaces

Source IP address and/or Source IP subnets.

ACE  Filters in Access Control Lists (ACL) that determine which network traffic is forwarded. An ACE is based on the following criteria:

Protocol

Protocol ID

Source Port

Destination Port

Wildcard Mask

Source IP Address

Destination IP Address

ACL (Access Control List)  Access Control Lists are used to grant, deny, or limit access devices, features, or applications.

Auto-negotiation Allows 10/100 Mbps or 10/100/1000 Mbps Ethernet ports to automatically establish the optimal duplex mode, flow control, and speed.

Back Pressure  A mechanism used with Half Duplex mode that enables a port not to receive a message.

Bandwidth  The transmission capacity of a given device or network.

Bandwidth Assignments  Indicates the amount of bandwidth assigned to a specific application, user, and/or interface.

Glossary

Baud  Indicates the number of signaling elements transmitted each second.

Best Effort  Indicates that traffic is assigned to the lowest priority queue, and packet delivery is not guaranteed.

Bit  A binary digit.

Boot  To start a device and cause it to start executing instructions.

Browser  An application program that provides a way to look at and interact with all the information on the World Wide Web.

Bridge  A device that connect two networks. Bridges are hardware specific, however they are protocol independent. Bridges operate at Layer 1 and Layer 2 levels.

Broadcast Domain  Devices sets that receive broadcast frames originating from any device within a designated set. Routers bind Broadcast domains, because routers do not forward broadcast frames.

Broadcast Storm  An excessive amount of broadcast messages simultaneously transmitted across a network by a single port. Forwarded message responses are heaped onto the network, overloading network resources or causing the network to time out.

Burst  A packet transmission at faster than normal rates. Bursts are limited in time and only occur under specific conditions.

Burst Size  Indicates the burst size transmitted at a faster than normal rate.

Byte  A unit of data that is usually eight bits long

Cable Modem  A device that connects a computer to the cable television network, which in turn connects to the Internet.

CBS (Committed Burst Size)  Indicates the maximum number of data bits transmitted within a specific time interval.

CIR (Committed Information Rate)  The data rate is averaged over a minimum time increment.

Class Maps  An aspect of Quality of Service system that is comprised of an IP ACL and/or a MAC ACL. Class maps are configured to match packet criteria, and are matched to packets in a first-fit fashion.

Combo Ports  A single logical port with two physical connections, including an RJ-45 connection and a SFP connection.

Communities  Specifies a group of users which retain the same system access rights.

Wireless-G Access Point with Power Over Ethernet

24

Image 28
Contents Wireless-G Access Point with Power Over Ethernet About This Guide About This GuideTable of Contents Appendix G Contact Information Chapter Chapter IntroductionChapter Planning Your Wireless Network Network TopologyRoaming Network LayoutChapter Product Overview Product OverviewFront Panel Back PanelChapter Installation InstallationPlacement Wall-MountConnecting the Access Point Chapter Advanced Configuration Advanced ConfigurationAccessing the Web-Based Utility Setup SetupSetup Time Wireless Basic Wireless SettingsWireless Wireless Security WEPWPA-Personal aka WPA-PSK WPA2-PersonalWPA-Enterprise WPA2-Personal MixedWPA2-Enterprise Disable WPA2-Enterprise MixedWireless Wireless Connection Control Wireless Advanced Wireless SettingsWireless Vlan & QoS AP Mode Administration ManagementAdministration Log LogAdministration Firmware Upgrade Administration Factory DefaultAdministration Reboot Administration Configuration Management Status Local NetworkStatus Wireless WiredWireless Status System PerformanceChapter Troubleshooting Appendix a TroubleshootingAppendix a Troubleshooting Does the Access Point function as a firewall? Appendix B Wireless Security Checklist Wireless Security ChecklistAppendix B General Network Security GuidelinesAppendix C Glossary Appendix CGlossary Glossary Smtp Simple Mail Transfer Protocol The standard Appendix C Specifications Appendix D SpecificationsAppendix D Limited Warranty Warranty InformationAppendix E Appendix F Regulatory InformationWireless Disclaimer Avis d’Industrie CanadaDansk Danish Miljøinformation for kunder i EU Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information

WAP2000 specifications

The Linksys WAP2000 is a robust wireless access point designed to enhance connectivity for both home and small business environments. This device provides a reliable solution for extending the reach of your existing network, ensuring that users can access high-speed internet with minimal interruptions.

One of the main features of the Linksys WAP2000 is its dual-band capability, which operates on both the 2.4 GHz and 5 GHz frequency bands. This dual-band technology allows for greater flexibility and less interference, accommodating more devices while maintaining optimal performance. Users can connect to the 5 GHz band for bandwidth-intensive activities, such as streaming and online gaming, while the 2.4 GHz band serves well for general browsing and connecting older devices.

The WAP2000 is equipped with the latest 802.11n wireless standard, offering speeds of up to 300 Mbps. This high throughput makes it an efficient choice for businesses that require swift data transfers and reliable connections. Additionally, the device supports Multiple Input Multiple Output (MIMO) technology, which uses multiple antennas to send and receive more data simultaneously, further enhancing its performance and range.

For ease of installation, the Linksys WAP2000 features Power over Ethernet (PoE) support. This allows the device to receive power through the Ethernet cable, eliminating the need for separate power adapters and simplifying the setup process. Additionally, its browser-based setup utility provides a user-friendly interface for configuration, enabling users to customize settings easily.

Security is a critical concern for any network, and the Linksys WAP2000 addresses this with various security features. It supports WPA/WPA2 encryption protocols, protecting data transmitted over the network from unauthorized access. Furthermore, the device includes MAC address filtering, which allows users to control which devices can connect to the network.

With a sturdy design and compact form factor, the Linksys WAP2000 is suitable for a variety of deployment scenarios, whether mounted on walls or placed on desks. Its versatility and performance make it an excellent choice for users looking to improve their wireless connectivity, ensuring that both guests and employees can enjoy a seamless online experience. Overall, the Linksys WAP2000 is an essential addition to any network, providing high-speed internet access and robust security features to keep users connected and safe.