Linksys WAP2000 manual Appendix F, Regulatory Information

Page 34

Appendix F

Appendix F: Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment or devices

•Connect the equipment to an outlet other than the receiver’s

•Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

Regulatory Information

Safety Notices

•Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.

•Do not use this product near water, for example, in a wet basement or near a swimming pool.

•Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Industry Canada Statement

This device complies with Industry Canada ICES-003 and RSS210 rules.

Operation is subject to the following two conditions:

1.This device may not cause interference and

2.This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna havingahighergainisstrictlyprohibitedperregulations of Industry Canada. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.

Industry Canada Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Wireless-G Access Point with Power Over Ethernet

30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Wireless-G Access Point with Power Over Ethernet About This Guide About This GuideTable of Contents Appendix G Contact Information Chapter Chapter IntroductionRoaming Chapter Planning Your Wireless NetworkNetwork Topology Network LayoutFront Panel Chapter Product OverviewProduct Overview Back PanelPlacement Chapter InstallationInstallation Wall-MountConnecting the Access Point Accessing the Web-Based Utility Chapter Advanced ConfigurationAdvanced Configuration Setup SetupSetup Time Wireless Basic Wireless SettingsWireless Wireless Security WEPWPA-Personal aka WPA-PSK WPA2-PersonalWPA-Enterprise WPA2-Personal MixedWPA2-Enterprise Disable WPA2-Enterprise MixedWireless Wireless Connection Control Wireless Advanced Wireless SettingsWireless Vlan & QoS AP Mode Administration ManagementAdministration Log LogAdministration Firmware Upgrade Administration Factory DefaultAdministration Reboot Administration Configuration Management Status Local NetworkWireless Status WirelessWired Status System PerformanceChapter Troubleshooting Appendix a TroubleshootingAppendix a Troubleshooting Does the Access Point function as a firewall? Appendix B Appendix B Wireless Security ChecklistWireless Security Checklist General Network Security GuidelinesAppendix C Glossary Appendix CGlossary Glossary Smtp Simple Mail Transfer Protocol The standard Appendix C Specifications Appendix D SpecificationsAppendix D Limited Warranty Warranty InformationAppendix E Appendix F Regulatory InformationWireless Disclaimer Avis d’Industrie CanadaDansk Danish Miljøinformation for kunder i EU Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information

WAP2000 specifications

The Linksys WAP2000 is a robust wireless access point designed to enhance connectivity for both home and small business environments. This device provides a reliable solution for extending the reach of your existing network, ensuring that users can access high-speed internet with minimal interruptions.

One of the main features of the Linksys WAP2000 is its dual-band capability, which operates on both the 2.4 GHz and 5 GHz frequency bands. This dual-band technology allows for greater flexibility and less interference, accommodating more devices while maintaining optimal performance. Users can connect to the 5 GHz band for bandwidth-intensive activities, such as streaming and online gaming, while the 2.4 GHz band serves well for general browsing and connecting older devices.

The WAP2000 is equipped with the latest 802.11n wireless standard, offering speeds of up to 300 Mbps. This high throughput makes it an efficient choice for businesses that require swift data transfers and reliable connections. Additionally, the device supports Multiple Input Multiple Output (MIMO) technology, which uses multiple antennas to send and receive more data simultaneously, further enhancing its performance and range.

For ease of installation, the Linksys WAP2000 features Power over Ethernet (PoE) support. This allows the device to receive power through the Ethernet cable, eliminating the need for separate power adapters and simplifying the setup process. Additionally, its browser-based setup utility provides a user-friendly interface for configuration, enabling users to customize settings easily.

Security is a critical concern for any network, and the Linksys WAP2000 addresses this with various security features. It supports WPA/WPA2 encryption protocols, protecting data transmitted over the network from unauthorized access. Furthermore, the device includes MAC address filtering, which allows users to control which devices can connect to the network.

With a sturdy design and compact form factor, the Linksys WAP2000 is suitable for a variety of deployment scenarios, whether mounted on walls or placed on desks. Its versatility and performance make it an excellent choice for users looking to improve their wireless connectivity, ensuring that both guests and employees can enjoy a seamless online experience. Overall, the Linksys WAP2000 is an essential addition to any network, providing high-speed internet access and robust security features to keep users connected and safe.
Top Page Image Contents