Allied Telesis manual Installing the AT-MC602 Provider Unit, Rack Mount Set on Slider

Page 30

AT-MC601 and AT-MC602 Installation and User’s Guide

Installing the AT-MC602 Provider Unit

The AT-MC602 Provider unit can only be installed in an AT-MCR12 rackmount chassis.

Warning

To prevent exposure to electric shock, the AT-MC602 Provider Unit must be installed in a RESTRICTED ACCESS LOCATION and performed by QUALIFIED SERVICE PERSONNEL.

Note

For Finland, Norway, and Sweden – When the AT-MC602 and the AT-MCR12 are used, a permanent ground conductor must be installed on the AT-MCR12 chassis.

For installation instructions of this ground conductor, refer to the AT-MCR12 Media Converter Rackmount Chassis Installation Manual (PN 613-10725-00).

To install the Provider unit in an AT-MCR12 rackmount chassis, perform the following steps:

1.Attach the unit to one of the sliders that will hold the unit in the chassis, as shown in Figure 13.

	ERR	LINK
LINE			PSTN
			MGMT	EXTENDED ETHERNET
				VDSL
10BaseT/ 100BaseTX	LINK	ACT	PWR	AT-MC601

Figure 13 Rack Mount - Set on Slider

30

Image 30

Contents Installation and User’s Guide Page Electrical Safety and Emission Statement Declaration Of ConformityAT-MC601 and AT-MC602 Installation and User’s Guide Contents Appendix a Preface How This Guide is OrganizedDocument Conventions Contacting Allied Telesyn Technical Support Summary of Features Product DescriptionOverview Vdsl Line throughLocation of Components Front PanelsHardware Features Pin AssignmentPstn Port 10/100 Mbps Twisted Pair Ethernet Port Pass-through 6/1Pin MDI Signal MDI-X Signal TX+ RX+Color Description 10/100Base-TX PortLine Port RS-232 Pin DIN Pin Signal Management CableAC Power Supply Input Port External AC/DC Power AdapterSoftware Features Installation Installation Safety Precautions Europe-ECOther Countries Additional Compliance Statements Selecting a Site for the Network Extender Cables Port Connector Cables Not IncludedUnpacking the Network Extender Installing the AT-MC601 Subscriber Unit Using Subscriber Unit On a DesktopPositioning The Switch Onto The Wall Screws Wall-Mounting Subscriber UnitPstn to Telephone Powering On Subscriber Unit Power On The Subscriber UnitInstalling the AT-MC602 Provider Unit Rack Mount Set on SliderRack Mount Set in Rack Internet Service Provider Provider UnitPowering On Provider Unit Warranty Registration Configuration Starting a Configuration Session Downloading Software Updates Cabling PreparationsOpening Configuration Software Configuring the Provider Unit Upstream/DownstreamMax Mbps Actual MbpsMin Mbps StatusApply AboutMean Square Error SNR of Received SignalCorrected RS errors /s Full Constellation LinkTC Synchronized Signal DetectedReduced Constellation Link Ethernet Encapsulation SyncCollision Counters Error CountersTxRx Counters ClearStop/Start Configuring the Subscriber Unit InstallNormal AT-MC601 and AT-MC602 Installation and User’s Guide Troubleshooting Communication Error Message Run on S Side Error Message AT-MC601 and AT-MC602 Installation and User’s Guide Default Configuration Settings Environmental Specifications Technical SpecificationsPhysical Specifications Power SpecificationsSafety and Electromagnetic Compatibility Certifications Translated Electrical Safety and Emission Information Safety Europe-ECOther Countries Sicherheit 6 Gefahr Durch BlitzschlagSikkerhed Europe EC 6 Fare Under Uvejr Veiligheid 6 Gevaar Voor BlikseminslagSécurité 6 Danger De FoudreStandardit Tämä tuote on seuraavien standardien mukainen 6 SalamaniskuvaaraStandard Questo prodotto è conforme ai seguenti standard 6 Pericolo Di FulminiSikkerhet 6 Fare For LynnedslagSegurança 6 Perigo De Choque Causado Por RaioSeguridad 6 Peligro De RayosSäkerhet 6 Fara För Blixtnedslag