8e6 Technologies TAR quick start Rack Mount Instructions for SL Servers, Install the Inner Slides

Page 15

Rack Mount Instructions for SL Servers

Rack Setup Suggestions

•Determine the placement of each component in the rack before you install the rails.

•Install the heaviest server components on the bottom of the rack first, and then work up.

Install the Inner Slides

1.Locate the right inner slide, (the slide that will be used on the right side of chassis when facing the front panel of the chassis).

2.Align the four (4) square holes on the right inner slide against the hooks on the right side of the chassis as show below on the left.

3.Securely attach the slide to the chassis with two M4 flat head screws and repeat the steps 1-3 to install the left inner slide to the left side of the chassis.

Install the Outer Slides

1.Measure the distance from the front rail of the rack to the rear rail of the rack.

2.Attach a short bracket to the rear side of the right outer slide, and a long bracket to the front side of the right outer slide as shown above on the right.

3.Adjust the short and long brackets to the proper distance so that the chassis can snugly fit into the rack.

4.Secure the slides to the cabinet with screws.

5.Repeat steps 1-4 for the left outer slide.

8e6 Threat Analysis Reporter Quick Start Guide

11

Image 15

Contents Guide 8e6 Threat Analysis Reporter Quick Start Guide Contents 8e 6 Threat Analysis Reporter Quick Start Guide Threat Analysis Reporter Introduction Conventions Used in this Document About this DocumentProcedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Mount the Server Rack Setup PrecautionsRack Mount Instructions for HL Servers Rack Setup SuggestionsInstall the Inner Rails Install the Outer Rails8e6 Threat Analysis Reporter Quick Start Guide Install the Server into the Rack Install the Server into a Telco Rack Install the Inner Slides Install the Outer SlidesRack Mount Instructions for SL Servers Install the Slide Assemblies to the Rack Install the Chassis into the Rack Rack Mount Instructions for MSA Servers Optional Install the Chassis Rails8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Traditional UP Racks 8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Open Racks 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Install the Chassis into the Rack Front of bezel Install the SL or HL Server BezelPower Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Initial Setup Procedures Quick Start Setup RequirementsLCD Panel Setup Requirements for SL and HL Units Link the Workstation to the Threat Analysis Reporter Quick Start Setup ProceduresMonitor and Keyboard Setup Serial Console SetupDiagram of SL chassis front panel, power button at far right HyperTerminal Setup Procedures 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Quick Start menu instructions Login screen, password prompts#s3tup#r3k Configure Network Interface screen 8e6 Threat Analysis Reporter Quick Start Guide Configure Domain Name Servers screen Configure default gateway screenConfigure Host Name screen Time zone regional configuration screen Configure Wizard user screen Administration menu Quick Start Setup confirmation screenLog Off, Disconnect the Peripherals System Status screenBandwidth Management Physically Connect the Unit to the NetworkLCD Panel Setup Procedures LCD Menu8e6 menu IP / LAN1 and LAN2 Current Patch LevelGateway DNS 1Host Name Regional Setting Time Zone, date, time Admin Console Wizard UserReboot Backlight LCD Options menuShutdown HeartbeatLCD Controls Access the Threat Analysis Reporter Administrator Console Wizard Setup ProceduresLog in to the Threat Analysis Reporter Wizard Wizard Register administrator 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide R3000 Wizard Register R3000 & ER8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Conclusion Server SettingsSL and MSA Units LED Indicator KeyLED Indicator Key Button Key LED Indicator Color Condition DescriptionHL Unit Rear LED Indicators for Hardware Status Monitoring RAID HL and SL UnitsModels HL-005-004, SL-004-004, MSA-004-004 Safety ComplianceDeclaration of the Manufacturer or Importer Electromagnetic Compatibility EMCElectromagnetic Compatibility Class a Notice EC Declaration of Conformity Preliminary Setup Procedures Other Required Installation ItemsUnpack the Ethernet Tap Unit from the Box Install the Ethernet Tap Unit Ports in front panel of NetOptics 10/100BaseT Tap Index 8e6 Threat Analysis Reporter Quick Start Guide