Cabletron Systems SEHI-22/24, SEHI-32/34 manual Monitoring Hub Performance

Page 21

Using the SEHI Hub View

•Blue indicates that the port has been disabled through management.

•Yellow indicates that the port is enabled but does not currently have a valid connection. This usually indicates that the device at the other end of the segment is turned off.

•Red indicates that the port is enabled, but is not able to pass packets. This generally means that the port has been segmented by management after experiencing an excessive number of collisions; for a BNC (thin coax) port, however, this may only mean that no cable or terminator has been connected.

When the Admin Status port display option is active, only two colors apply: a port will be displayed in green if it is enabled by management, regardless of whether or not there is a cable attached or a valid link signal detected; a port disabled by management will display as blue.

Monitoring Hub Performance

The information displayed in the Hub View can give you a quick summary of device activity, status, and configuration. SPMA can also provide further details about device performance via its three-level menu structure. The Device, Module, and Port menus (Figure 2-5) give you control over the device at these three levels and give you access to the tools, menus, and windows that let you monitor specific aspects of device performance, change hub display options, and set SEHI operating and notification parameters. Remember, though many functions will operate the same at each level, those accessed via the Device menu control or provide information about the SEHI-managed stack as a whole; those accessed via the Module menu control or provide information about a single hub in the stack; and those accessed via the Port menu control or provide information about a single port.

Figure 2-5. The SEHI’s Device, Module, and Port Menus

Hub performance data available through these menus includes:

Monitoring Hub Performance

2-7

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Complete Networking Solution Page Virus Disclaimer Applicable to licenses to the United States Government only Restricted Rights NoticeContents Chapter Source Addressing Chapter Repeater RedundancyChapter Security Appendix a Sehi MIB StructureIntroduction to Spma For the SEHI-22/24 and SEHI-32/34 Using the Sehi User’s GuideUsing the Sehi User’s Guide Conventions What’s not in the Sehi User’s GuideScreen Displays Introduction to Spma for the SEHI-22/24 and SEHI-32/34 Button Using the MouseFTP Getting HelpSehi Firmware Page Using the Hub View Using the Sehi Hub ViewHub View Front Panel Navigating Through the Hub ViewDate and Time UptimeDevice Name LocationUsing the Sehi Hub View Using the Mouse in the Hub View Ports Display Port Display Form Hub View Port Color CodesMonitoring Hub Performance Port Display Form ErrorsLoad CollisionsPort Type Frame SizesChecking Device Status and Updating Front Panel Info Name and LocationContact Checking Module Status Chassis TypeName Checking Repeater Status Active UsersModule Type Link Status Checking Port StatusMedia Type StatusTopology Type Checking StatisticsTotal Packets Received BytesAvg Packet Size Broadcast PacketsAlignment Errors Total ErrorsCRC Errors Multicast PacketsGiant Frames Runt FramesProtocols Viewing the Port Source Address ListManaging the Hub Contact Status Setting the Polling IntervalsDevice General Status Enabling/Disabling PortsDevice Configuration Port Operational StateUsing the Sehi Hub View Using the Sehi Hub View Managing the Hub Link/Seg Traps What is a Segmentation Trap?What is a Link Trap? Enabling and Disabling Link/Seg TrapsFrom the icon From the Hub View From the command line stand-alone modeViewing and Configuring Link/Seg Traps for Hub Modules Configuring Link/Seg Traps for the RepeaterModule Traps Window Viewing and Configuring Link/Seg Traps for PortsPort Traps Window Repeater Redundancy Setting Network Circuit RedundancySpmarun r4red IP address community name Configuring a Redundant CircuitChannel X Redundancy Window Add Circuit Address Window To set the Poll Interval Monitoring RedundancyClick in the All Circuits box Displaying the Source Address List Source AddressingDisplaying the Source Address List Source Addressing Setting the Ageing Time Setting the Hash TypeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Module- and Port-level Traps Device-level TrapsSource Addressing Source Addressing Port Source Address Traps Window Finding a Source AddressFind Source Address Window Click on to exit the window Source Addressing Finding a Source Address Security Spmarun r4sec IP address SU community name What is LANVIEWSECURE?New definitions for station and trunk ports Secure address assignmentTrunk port security Continuous learning mode Newest Lanviewsecure FeaturesConfigurable violation response Full or partial security against eavesdroppingLearned addresses reset Security on Non-LANVIEWSECUREHubsForced non-secure status Configuring Security Security To assign secure addresses to a port Addresses Window Add MAC Address Window Resetting Learned AddressesTips for Successfully Implementing Eavesdropper Protection Enabling Security and Traps Repeater-level Security and Traps Channel a Security Window Hub-level Security and TrapsChannel a Module Security Window Port-level Security and TrapsChannel a Port Security Window Security Security Enabling Security and Traps Ietf MIB Support Sehi MIB StructureSehi Chassis MGR Sehi IP Services Sehi Host ServicesBrief Word About MIB Components and Community Names Repeater OneSehi MIB Structure Sehi MIB Structure Index Index-2 Index-3 Index Index-4

SEHI-22/24, SEHI-32/34 specifications

Cabletron Systems was a notable player in the networking hardware market during the rise of local area networks (LANs) in the late 20th century. Among its innovative products were the SEHI-22/24 and SEHI-32/34 modules, which were designed to enhance network capabilities in enterprise environments.

The SEHI-22/24 and SEHI-32/34 were versatile high-performance Ethernet switch modules that offered significant advantages in network management and connectivity. These modules were designed to work with Cabletron's modular switching and routing architecture, allowing for scalable solutions tailored to specific network demands. A key feature of the SEHI series was its support for a range of Ethernet standards, ensuring compatibility with diverse networking environments.

One notable characteristic of the SEHI-22/24 was its ability to support both 10Base-T and 100Base-TX Ethernet technologies. This dual support enabled organizations to leverage existing 10 Mbps infrastructure while facilitating upgrades to 100 Mbps speeds without needing a complete overhaul of the network. Similarly, the SEHI-32/34 offered even greater connectivity options, accommodating more users and devices while maintaining high throughput and low latency.

In terms of management features, the SEHI series was equipped with extensive traffic management capabilities, including Quality of Service (QoS) features that prioritized bandwidth for critical applications. This ensured that essential services such as voice over IP (VoIP) and video conferencing could function optimally, even during heavy network loads.

Furthermore, both modules featured advanced diagnostics and monitoring tools that provided network administrators with critical insights into traffic patterns and potential bottlenecks. This functionality was essential for maintaining network health and optimizing performance, especially in dynamic business environments.

Security also played a crucial role in the design of the SEHI-22/24 and SEHI-32/34. The modules incorporated support for various authentication methods and access controls, ensuring that sensitive data remained protected within the corporate network.

In summary, Cabletron Systems’ SEHI-22/24 and SEHI-32/34 offered significant advancements in Ethernet switching technology, allowing organizations to build robust, scalable, and secure networks. With their impressive features, compatibility, and capacity for management and security, these modules were instrumental in shaping reliable networking solutions for enterprises navigating the rapidly evolving digital landscape.
Top Page Image Contents