Cabletron Systems SEHI-32/34, SEHI-22/24 manual Runt Frames, Giant Frames

Page 32

Using the SEHI Hub View

802.3specifications, or a node on the net is transmitting without first listening for carrier sense (and beginning its illegal transmission more than 51.2 ∝s after the first station began transmitting). Note that in both cases, the occurrence of the errors can be intermittent: in the case of excessive network length, OOW collisions will only occur when the farthest stations transmit at the same time; in the case of the node which is transmitting without listening, the malfunctioning node may

only fail to listen occasionally, and not all of its failures to listen will result in OOW collisions — some may simply result in collisions (if the 51.2 ∝s window has not yet closed), and some will get through fine (if no one else happens to be transmitting).

Runt Frames

The number of received packets smaller than the minimum Ethernet frame size of 64 bytes (excluding preamble). This minimum size is tied to the maximum propagation time of an Ethernet network segment — the maximum propagation time is 51.2 ∝s, and it takes approximately 51.2 ∝s to transmit 64 bytes of data; therefore, every node on the segment should be aware that another node is transmitting before the transmission is complete, providing for more accurate collision detection. Runts can sometimes result from collisions, and, as such, may be the natural by-product of a busy network; however, they can also indicate a hardware (packet formation), transmission (corrupted data), or network design (more than four cascaded repeaters) problem.

Giant Frames

The number of received packets that are longer than the maximum Ethernet size of 1518 bytes (excluding preamble). Giant packets typically occur when you have a jabbering node on your network — one that is continuously transmitting, or transmitting improperly for short bursts — probably due to a bad transmitter on the network interface card. Giant packets can also result from packets being corrupted as they are transmitted, either by the addition of garbage signal, or by the corruption of the bits that indicate frame size.

The SEHI Error Priority Scheme

Each Cabletron device employs an error priority scheme which determines how packets with multiple errors will be counted, and ensures that no error packet is counted more than once. The priority scheme for the SEHI counts errors in the following order:

1.

OOW Collisions

2.

Runts

3.

Giants

4.

Alignment Errors

5.

CRC Errors

Knowing the priority scheme employed by the SEHI can tell you a lot about the error counts you are seeing. For example, you know that the number of packets

2-18

Monitoring Hub Performance

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Complete Networking Solution Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Repeater Redundancy Chapter Source AddressingChapter Security Appendix a Sehi MIB StructureUsing the Sehi User’s Guide Introduction to Spma For the SEHI-22/24 and SEHI-32/34Using the Sehi User’s Guide Screen Displays ConventionsWhat’s not in the Sehi User’s Guide Introduction to Spma for the SEHI-22/24 and SEHI-32/34 Using the Mouse ButtonGetting Help FTPSehi Firmware Page Using the Sehi Hub View Using the Hub ViewNavigating Through the Hub View Hub View Front PanelUptime Date and TimeDevice Name LocationUsing the Sehi Hub View Using the Mouse in the Hub View Ports Display Hub View Port Color Codes Port Display FormMonitoring Hub Performance Errors Port Display FormLoad CollisionsFrame Sizes Port TypeContact Checking Device Status and Updating Front Panel InfoName and Location Name Checking Module StatusChassis Type Module Type Checking Repeater StatusActive Users Checking Port Status Link StatusStatus Media TypeChecking Statistics Topology TypeReceived Bytes Total PacketsAvg Packet Size Broadcast PacketsTotal Errors Alignment ErrorsCRC Errors Multicast PacketsRunt Frames Giant FramesViewing the Port Source Address List ProtocolsManaging the Hub Setting the Polling Intervals Contact StatusEnabling/Disabling Ports Device General StatusDevice Configuration Port Operational StateUsing the Sehi Hub View Using the Sehi Hub View Managing the Hub What is a Segmentation Trap? Link/Seg TrapsFrom the icon What is a Link Trap?Enabling and Disabling Link/Seg Traps From the command line stand-alone mode From the Hub ViewConfiguring Link/Seg Traps for the Repeater Viewing and Configuring Link/Seg Traps for Hub ModulesViewing and Configuring Link/Seg Traps for Ports Module Traps WindowPort Traps Window Setting Network Circuit Redundancy Repeater RedundancyConfiguring a Redundant Circuit Spmarun r4red IP address community nameChannel X Redundancy Window Add Circuit Address Window Monitoring Redundancy To set the Poll IntervalClick in the All Circuits box Source Addressing Displaying the Source Address ListDisplaying the Source Address List Source Addressing Setting the Hash Type Setting the Ageing TimeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Device-level Traps Module- and Port-level TrapsSource Addressing Source Addressing Finding a Source Address Port Source Address Traps WindowFind Source Address Window Click on to exit the window Source Addressing Finding a Source Address Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community nameTrunk port security New definitions for station and trunk portsSecure address assignment Newest Lanviewsecure Features Continuous learning modeConfigurable violation response Full or partial security against eavesdroppingForced non-secure status Learned addresses resetSecurity on Non-LANVIEWSECUREHubs Configuring Security Security To assign secure addresses to a port Addresses Window Resetting Learned Addresses Add MAC Address WindowTips for Successfully Implementing Eavesdropper Protection Enabling Security and Traps Repeater-level Security and Traps Hub-level Security and Traps Channel a Security WindowPort-level Security and Traps Channel a Module Security WindowChannel a Port Security Window Security Security Enabling Security and Traps Sehi Chassis MGR Ietf MIB SupportSehi MIB Structure Sehi Host Services Sehi IP ServicesBrief Word About MIB Components and Community Names Repeater OneSehi MIB Structure Sehi MIB Structure Index Index-2 Index-3 Index Index-4

SEHI-22/24, SEHI-32/34 specifications

Cabletron Systems was a notable player in the networking hardware market during the rise of local area networks (LANs) in the late 20th century. Among its innovative products were the SEHI-22/24 and SEHI-32/34 modules, which were designed to enhance network capabilities in enterprise environments.

The SEHI-22/24 and SEHI-32/34 were versatile high-performance Ethernet switch modules that offered significant advantages in network management and connectivity. These modules were designed to work with Cabletron's modular switching and routing architecture, allowing for scalable solutions tailored to specific network demands. A key feature of the SEHI series was its support for a range of Ethernet standards, ensuring compatibility with diverse networking environments.

One notable characteristic of the SEHI-22/24 was its ability to support both 10Base-T and 100Base-TX Ethernet technologies. This dual support enabled organizations to leverage existing 10 Mbps infrastructure while facilitating upgrades to 100 Mbps speeds without needing a complete overhaul of the network. Similarly, the SEHI-32/34 offered even greater connectivity options, accommodating more users and devices while maintaining high throughput and low latency.

In terms of management features, the SEHI series was equipped with extensive traffic management capabilities, including Quality of Service (QoS) features that prioritized bandwidth for critical applications. This ensured that essential services such as voice over IP (VoIP) and video conferencing could function optimally, even during heavy network loads.

Furthermore, both modules featured advanced diagnostics and monitoring tools that provided network administrators with critical insights into traffic patterns and potential bottlenecks. This functionality was essential for maintaining network health and optimizing performance, especially in dynamic business environments.

Security also played a crucial role in the design of the SEHI-22/24 and SEHI-32/34. The modules incorporated support for various authentication methods and access controls, ensuring that sensitive data remained protected within the corporate network.

In summary, Cabletron Systems’ SEHI-22/24 and SEHI-32/34 offered significant advancements in Ethernet switching technology, allowing organizations to build robust, scalable, and secure networks. With their impressive features, compatibility, and capacity for management and security, these modules were instrumental in shaping reliable networking solutions for enterprises navigating the rapidly evolving digital landscape.
Top Page Image Contents