Cabletron Systems SEHI-32/34, SEHI-22/24 Hub-level Security and Traps, Channel a Security Window

Page 78

Security

Figure 6-5. Channel A Security Window

3.In the Security Mode field, click mouse button 1 on the appropriate selection to apply Full or Continuous lock status to all ports on the selected repeater channel, or to Unlock all ports on the channel. (Note that if your SEHI does not support the newest security enhancements, the Continuous selection will be unavailable.)

4.In the Send Trap field, click mouse button 1 on the appropriate selection to Enable or Disable traps for the selected repeater channel.

5.Click mouse button 1 on to save your changes; the new status will be displayed in each field to the right of the field name. Click on to exit the window.

Hub-level Security and Traps

Locking ports at the hub level applies all applicable protections (as configured via the Port Security window) to each port on the selected hub or hubs.

NOTE

If you select a group of hubs whose ports have different security capabilities, you may still be able to select and apply security states which are not applicable to all ports. Applying these kinds of settings will have no adverse affect on your network devices: those ports which can accept the set will do so; those which cannot will either ignore the set or issue a Set Failed.

To enable or disable locking and/or traps at the hub level:

1.In the Repeater Security window, click to select the appropriate repeater interface in the scroll list.

2.Click mouse button 1 on ; the Channel A Module Security window, Figure 6-6, will appear. Note that the current hub-level settings are

6-14

Enabling Security and Traps

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Complete Networking Solution Page Virus Disclaimer Restricted Rights Notice Applicable to licenses to the United States Government onlyContents Chapter Security Chapter Repeater RedundancyChapter Source Addressing Appendix a Sehi MIB StructureUsing the Sehi User’s Guide Introduction to Spma For the SEHI-22/24 and SEHI-32/34Using the Sehi User’s Guide Conventions What’s not in the Sehi User’s GuideScreen Displays Introduction to Spma for the SEHI-22/24 and SEHI-32/34 Using the Mouse ButtonGetting Help FTPSehi Firmware Page Using the Sehi Hub View Using the Hub ViewNavigating Through the Hub View Hub View Front PanelDevice Name UptimeDate and Time LocationUsing the Sehi Hub View Using the Mouse in the Hub View Ports Display Hub View Port Color Codes Port Display FormMonitoring Hub Performance Load ErrorsPort Display Form CollisionsFrame Sizes Port TypeChecking Device Status and Updating Front Panel Info Name and LocationContact Checking Module Status Chassis TypeName Checking Repeater Status Active UsersModule Type Checking Port Status Link StatusStatus Media TypeChecking Statistics Topology TypeAvg Packet Size Received BytesTotal Packets Broadcast PacketsCRC Errors Total ErrorsAlignment Errors Multicast PacketsRunt Frames Giant FramesViewing the Port Source Address List ProtocolsManaging the Hub Setting the Polling Intervals Contact StatusDevice Configuration Enabling/Disabling PortsDevice General Status Port Operational StateUsing the Sehi Hub View Using the Sehi Hub View Managing the Hub What is a Segmentation Trap? Link/Seg TrapsWhat is a Link Trap? Enabling and Disabling Link/Seg TrapsFrom the icon From the command line stand-alone mode From the Hub ViewConfiguring Link/Seg Traps for the Repeater Viewing and Configuring Link/Seg Traps for Hub ModulesViewing and Configuring Link/Seg Traps for Ports Module Traps WindowPort Traps Window Setting Network Circuit Redundancy Repeater RedundancyConfiguring a Redundant Circuit Spmarun r4red IP address community nameChannel X Redundancy Window Add Circuit Address Window Monitoring Redundancy To set the Poll IntervalClick in the All Circuits box Source Addressing Displaying the Source Address ListDisplaying the Source Address List Source Addressing Setting the Hash Type Setting the Ageing TimeLocking Source Addresses Source Address Locking on Older Devices Configuring Source Address Traps Device-level Traps Module- and Port-level TrapsSource Addressing Source Addressing Finding a Source Address Port Source Address Traps WindowFind Source Address Window Click on to exit the window Source Addressing Finding a Source Address Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community nameNew definitions for station and trunk ports Secure address assignmentTrunk port security Configurable violation response Newest Lanviewsecure FeaturesContinuous learning mode Full or partial security against eavesdroppingLearned addresses reset Security on Non-LANVIEWSECUREHubsForced non-secure status Configuring Security Security To assign secure addresses to a port Addresses Window Resetting Learned Addresses Add MAC Address WindowTips for Successfully Implementing Eavesdropper Protection Enabling Security and Traps Repeater-level Security and Traps Hub-level Security and Traps Channel a Security WindowPort-level Security and Traps Channel a Module Security WindowChannel a Port Security Window Security Security Enabling Security and Traps Ietf MIB Support Sehi MIB StructureSehi Chassis MGR Brief Word About MIB Components and Community Names Sehi Host ServicesSehi IP Services Repeater OneSehi MIB Structure Sehi MIB Structure Index Index-2 Index-3 Index Index-4

SEHI-22/24, SEHI-32/34 specifications

Cabletron Systems was a notable player in the networking hardware market during the rise of local area networks (LANs) in the late 20th century. Among its innovative products were the SEHI-22/24 and SEHI-32/34 modules, which were designed to enhance network capabilities in enterprise environments.

The SEHI-22/24 and SEHI-32/34 were versatile high-performance Ethernet switch modules that offered significant advantages in network management and connectivity. These modules were designed to work with Cabletron's modular switching and routing architecture, allowing for scalable solutions tailored to specific network demands. A key feature of the SEHI series was its support for a range of Ethernet standards, ensuring compatibility with diverse networking environments.

One notable characteristic of the SEHI-22/24 was its ability to support both 10Base-T and 100Base-TX Ethernet technologies. This dual support enabled organizations to leverage existing 10 Mbps infrastructure while facilitating upgrades to 100 Mbps speeds without needing a complete overhaul of the network. Similarly, the SEHI-32/34 offered even greater connectivity options, accommodating more users and devices while maintaining high throughput and low latency.

In terms of management features, the SEHI series was equipped with extensive traffic management capabilities, including Quality of Service (QoS) features that prioritized bandwidth for critical applications. This ensured that essential services such as voice over IP (VoIP) and video conferencing could function optimally, even during heavy network loads.

Furthermore, both modules featured advanced diagnostics and monitoring tools that provided network administrators with critical insights into traffic patterns and potential bottlenecks. This functionality was essential for maintaining network health and optimizing performance, especially in dynamic business environments.

Security also played a crucial role in the design of the SEHI-22/24 and SEHI-32/34. The modules incorporated support for various authentication methods and access controls, ensuring that sensitive data remained protected within the corporate network.

In summary, Cabletron Systems’ SEHI-22/24 and SEHI-32/34 offered significant advancements in Ethernet switching technology, allowing organizations to build robust, scalable, and secure networks. With their impressive features, compatibility, and capacity for management and security, these modules were instrumental in shaping reliable networking solutions for enterprises navigating the rapidly evolving digital landscape.
Top Page Image Contents