Ricoh A741 manual Installation, Eprom replacement, New SIMulations, Sim

Page 13

2 Installation

2.1EPROM replacement

In the event of an EPROM change the following procedure will enable the technician to replace the prom and bring the A741 unit back on line.

The following (minimum) procedure should be followed after replacing the EPROM, failing to do so may result in some unpredictable behavior.

•Run SIM 66 and write down the developer initial value

•Run SIM 70 (backup RAM initialization) and wait for the OK message

•Run SIM 81 to re-set the display language from Japanese to the desired language.

•Run SIM 66 again, re-entering the value recorded above

•Re-enter all factory default values as found on the large label on the inside of the left cover or on the rear panel.

•Clean the contact glass and rollers and perform SIM 120 (γ auto adjust)

•Press the clear key and all clear key, select SIM 001 and return to the normal operation mode. Switch the A741 off and on again.

2.2New SIMulations

Several new SIMulations are used to control the A741 Repro System, the 2 most important are discussed below:

SIM 115

Set to '2: UNIT ON', this will enable the interface, if set to '1: UNIT OFF' the server PC will not detect the A741. Default setting after changing the EPROM’s is off.

SIM 117

Leading edge adjustment for scanning via A741 Repro System.

How to check: Scan an image and print this again at 100%,. See if the distance from the top of the paper to the top of the image is the same on the original and the copy, if not change the value of SIM 117.

Print Server Manual

5

A741

Image 13

Contents A741 Controller Print Server Manual Page Introduction Page Table of Contents Frequently Asked Questions General Installing / Using Network ClientsFrequently Asked Questions A741 Repro System Overview Direct Printing from Autocad A741 Repro ProgramFrequently Asked Questions Image VIEWING/HANDLING Frequently Asked Questions PRINTING/PLOTTINGFrequently Asked Questions Network Frequently Asked Questions ScanningGlossary Description of Lbtest Program A741 specifications basic SpecificationsA741 Repro Specifications File FormatsA741 Repro functions Printing Printer DriversA741 Repro functions Scanning A741 Repro functions ManagementOptions Minimum PC specifications Server onlyA741 Eprom replacement InstallationNew SIMulations SIMPCI card installation PC SpecificationsA741 internal cabling Size of paging file PC bios setting1 A741 Repro System Software installation A741 Repro Software installationUpgrading an existing installation Various hints & Tips on installationPrint Server Manual A741 How do I de-install the A741 Repro System program? PC networking With a previous network installation Print Server PC Functional block diagram of A741 Repro SystemA741 Signs of problems Trouble-shootingProblem listing GeneralDetailed corrective actions A741 produces blank pages when printingSelect the correct PCI slot for the A741 Repro System card Starting stopping Littlebear driver and rfxServer Each time I re-boot the Server PC, rfxServer will not startRfxServer will not start Cannot maximize Client window Use of the Event logA741 Starting the Lbtest program Lbtest Commands Lbtest Version x.x, OptionsPrint, Scan, test Button, or Fifo tests Press button on cardTest command Fifo Test command PrintTest Selection Re-starting or stopping the Littlebear driver and rfxServerInstalling the Repro Sytem from CD-ROM Installing / Using Network ClientsInstalling Xi Repro Server/ Local Client system System A741 Repro Server preparationMultiple Remote Clients Installing the Remote Client system on remote PC’sView the status of a remote A741 printer A741 Direct printing from AutoCAD A741 A741 Repro Program Introduction Setting program optionsImporting documents, how are they processed? Setting program defaultsUse of stamps Use of pensetsA741 What is the purpose of the Xi Repro System Print Server? Frequently Asked Questions GeneralCan I use the A741 Print Server for other jobs as well? Can I use an existing PC from the customer?What is rasterising? What is the difference between printing and plotting?Raster VectorWhat is vectorising? A741 Network block diagram Frequently Asked Questions A741 Repro System overviewA741 Frequently Asked Questions Printing/Plotting Can we print multiple documents? HP-GL & HP-GL/2Can we do group or set printing? What is a penset?Can we add information text to each printed document? Can we define custom pen sets?A741 Can we preview the document before plotting/printing? Frequently Asked Questions Image Viewing/HandlingCan we modify the image before it will be printed? Which image handling options does A741 Repro have?A741 Can we print via a network? Frequently Asked Questions NetworkWhich networks & protocols can we use? Can we submit print jobs via e-mail?What protocols are compatible with the A741 Print Server? How are licenses configured for the A741 Print Server?Print Server Manual A741 A741 Frequently Asked Questions Scanning What is de-speckle? Can we scan at a lower resolution to reduce the filesize?What is de-skew? What is the purpose of a project? Frequently Asked Questions Project ManagementDo we provide any kind of accounting? A741 AMS GlossaryAscii APSDOS FAQDPI GUI GDIHP-GL HtmlLAN IPX/SPXOCR PCL OSDPDL PPMScsi ROMSoho TCP/IPWPS TwainWysiwig A741 Command Lbtest CommandsPurpose Of Document Command c Command s Command rCommand d Command wCommand t Command fCommand q Exit Lbtest Troubleshooting Print Server Manual A741 A741