Ricoh A741 manual Test Selection, Test command Print, Test command Fifo

Page 30

properly. Please make sure the A741 is on-line, since there will be no feedback by this test. The test pattern is fully generated by the controller card and can be issued at all times, even if the A741 Repro System software is not installed.

4.9.3Test Selection

Inorder to perform the following procedures it only necessary to select the "t" from the LBTEST command list aove. This is where the following tests are located.

4.9.4Test command – B(utton) Select "B" from the commands listed

under "t". Same test as pressing the button on the Little Bear card above. This time the command is given by software with minimal interaction with the controller card. Again, the test print is generated by the controller.

4.9.5Test command – P(rint)

Select "P" from the commands listed under "t". A more comprehensive test. The LBTEST program will generate a checker-board test pattern simulating the normal data transfer. If this test works o.k., then basically the PC and the PCI card are working fine.

4.9.6Test command – F(ifo)

Select "F" from the commands listed under "t". This test is mainly used to test the communication between the software and controller hardware. If there are any PCI bus problems this test will fail. (see chapter 4.4.3, Select the correct PCI slot for the A741 Repro System card)

4.9.7Re-starting or stopping the Littlebear driver and rfxServer

First make sure that the rfxServer program is stopped (see chapter 4.5, Starting (stopping) Littlebear driver and rfxServer). Folow the same procedure used for stopping the littleBear driver to restart the system. If the system will not restart (see chapter 4.5, Starting (stopping) Littlebear driver and rfxServer). or simply shut the system down and restart.

A741

22

Print Server Manual

Image 30

Contents A741 Controller Print Server Manual Page Introduction Page Table of Contents Frequently Asked Questions A741 Repro System Overview Installing / Using Network ClientsFrequently Asked Questions General Direct Printing from Autocad A741 Repro ProgramFrequently Asked Questions Network Frequently Asked Questions PRINTING/PLOTTINGFrequently Asked Questions Image VIEWING/HANDLING Frequently Asked Questions ScanningGlossary Description of Lbtest Program A741 Repro Specifications SpecificationsA741 specifications basic File FormatsA741 Repro functions Scanning Printer DriversA741 Repro functions Printing A741 Repro functions ManagementMinimum PC specifications Server only OptionsA741 New SIMulations InstallationEprom replacement SIMPC Specifications PCI card installationA741 internal cabling PC bios setting Size of paging fileUpgrading an existing installation A741 Repro Software installation1 A741 Repro System Software installation Various hints & Tips on installationPrint Server Manual A741 How do I de-install the A741 Repro System program? PC networking With a previous network installation Functional block diagram of A741 Repro System Print Server PCA741 Problem listing Trouble-shootingSigns of problems GeneralA741 produces blank pages when printing Detailed corrective actionsSelect the correct PCI slot for the A741 Repro System card Each time I re-boot the Server PC, rfxServer will not start Starting stopping Littlebear driver and rfxServerRfxServer will not start Use of the Event log Cannot maximize Client windowA741 Print, Scan, test Button, or Fifo tests Lbtest Commands Lbtest Version x.x, OptionsStarting the Lbtest program Press button on cardTest Selection Test command PrintTest command Fifo Re-starting or stopping the Littlebear driver and rfxServerInstalling Xi Repro Server/ Local Client system System Installing / Using Network ClientsInstalling the Repro Sytem from CD-ROM A741 Repro Server preparationInstalling the Remote Client system on remote PC’s Multiple Remote ClientsView the status of a remote A741 printer A741 Direct printing from AutoCAD A741 Introduction Setting program options A741 Repro ProgramSetting program defaults Importing documents, how are they processed?Use of pensets Use of stampsA741 Can I use the A741 Print Server for other jobs as well? Frequently Asked Questions GeneralWhat is the purpose of the Xi Repro System Print Server? Can I use an existing PC from the customer?Raster What is the difference between printing and plotting?What is rasterising? VectorWhat is vectorising? A741 Frequently Asked Questions A741 Repro System overview Network block diagramA741 Frequently Asked Questions Printing/Plotting HP-GL & HP-GL/2 Can we print multiple documents?Can we add information text to each printed document? What is a penset?Can we do group or set printing? Can we define custom pen sets?A741 Can we modify the image before it will be printed? Frequently Asked Questions Image Viewing/HandlingCan we preview the document before plotting/printing? Which image handling options does A741 Repro have?A741 Which networks & protocols can we use? Frequently Asked Questions NetworkCan we print via a network? Can we submit print jobs via e-mail?How are licenses configured for the A741 Print Server? What protocols are compatible with the A741 Print Server?Print Server Manual A741 A741 Frequently Asked Questions Scanning Can we scan at a lower resolution to reduce the filesize? What is de-speckle?What is de-skew? Frequently Asked Questions Project Management What is the purpose of a project?Do we provide any kind of accounting? A741 Ascii GlossaryAMS APSFAQ DOSDPI HP-GL GDIGUI HtmlIPX/SPX LANOCR PDL OSDPCL PPMSoho ROMScsi TCP/IPTwain WPSWysiwig A741 Lbtest Commands CommandPurpose Of Document Command c Command r Command sCommand w Command dCommand f Command tCommand q Exit Lbtest Troubleshooting Print Server Manual A741 A741