Ricoh AP305 operating instructions Installing the Ieee 1284 Parallel Type305

Page 47

Installing the IEEE 1284 Parallel Type305

Installing the IEEE 1284 Parallel Type305

RCAUTION:

•Make sure to turn off the printer and wait for about 30 minutes before installing options. Not waiting for the printer to cool down can result in a burn.

Note

❒The parallel interface board can be attached to either the left or the right side of the back of your print- er. This procedure is for attaching to the left side.

❒You cannot install two parallel in- terface boards at a time.

A Check the contents of the box for the following items.

•Parallel interface board

•Installation Guide

B Turn off the printer's power switch and remove all cables and cords from the printer.

C Remove screws and remove the left back plate.

TFWX185E

Note

❒A coin can be used to remove the screws.

D Insert the IEEE 1284 Parallel Type305 into the slot and fasten it

with screws that were removed in step C, as shown in the illustra- tion.

2

TFWP080E

Note

❒A coin can be used to fasten the screws.

E Attach the interface cable to the parallel interface connector of the printer. Secure the cable with the metal fittings.

Important

❒Rating voltage of the parallel in- terface connector for the com- puter; Max. DC 5V.

F Attach the other end of the inter- face cable to the interface connec- tor of the computer, and secure the cable.

G Plug the printer's power cord back into the printer and the wall socket. Turn on the printer's pow- er switch.

H Print a configuration page to con- firm that parallel interface board is properly installed.

Reference

⇒P.107 “Printing the Configura- tion Page”

17

Image 47

Contents Operating Instructions Overseas Affiliates Page Means Power on Means Power OFF Page Means Power on Means Power OFF Page Means Power on Means Power OFF Trademarks Safety During Operation Safety InformationIii Page Energy Star Program Low-power mode Energy Saver modeSpecifications Additive Emitted and Subtractive Reflected Color Models Color GuideColor Printing Basics Vii Printed Color 600 dpi 300 dpi Example of Color Adjustments Using the Printer DriverResolution Limitation Edge SmoothingAuto OffToner Saving Fine Image PrintingStandard FastReference Color Adjustments Using the Printer DriverColor Correction Off VividBit PhotographicColor Level Saturation BrightnessContrast Color Balance Operating Instructions this manual Quick Installation GuideManuals for Your Printer Manuals for Your PrinterPreparation How to Read this ManualSymbols Table of Contents Menu Settings Error & Status MessagesCleaning and Adjusting the Printer Setting Menus Protecting the MenusConsumables 120 Glossaries 122 Printing the Color Sample 110 Resetting Menus 111Moving and Transporting the Printer 115 Specifications 116 Memory Capacity and Paper Size 113Xxii Exterior-Front View Guide to the PrinterPaper Tray Bypass trayExterior-Rear View Interior Operation Panel Data In indicator Error indicatorReady Turning the Printer On and OffTurning On the Printer Warming UpGetting Acquainted Installing Options RICOH-SCRIPT2 Type305 ⇒ P.13 Paper Feed Unit Type305 ⇒ P.19 Available OptionsInterface Board Memory Unit ⇒ P.11⇒ P.107 Printing the Configura- tion Installing the Memory Unit SimmInstalling Options Check the contents of the box for the following items Installing the RICOH-SCRIPT2 Type305Reference Installing Network Interface Board Type305 Reference Installing the Ieee 1284 Parallel Type305 Installing Options Move the printer to make install- ing space Installing the Paper Feed Unit Type305Place the printer on the paper feed unit Remove both pieces of adhesive tapePull out the paper tray, and re- move the padding Remove the ring attached to the red tagInstalling the Paper Feed Unit Type305 Installing Options Press Menu Press UT until the following message appears Menu System Menu011.022.033.044 Jjl/# System Menu j 39.Active PTL. lActive PTL All Active System Menu j 32.IP Address l191.168.015.016 j System Menu Net BootNet Boot None Subnet Mask Access Control Address and Access Control MaskSystem Menu Frame NW Frame NW Auto SelectThese settings control only printing requests Page Before Installing the Printer Driver Installing the IPDL-C Printer DriverInstalling the Printer Drivers Plug and Play Windows 95/98 Installing the IPDL-C Printer DriverPrinter Driver Installation When Windows 95/98 starts normally Installing the Printer Driver Using Plug and PlayWhen the New Hardware Found dialog appears When the Device Driver Wizard appearsClick Finish Restart Windows after completing the installationClick OK Click Browse Installing the Printer Driver Without Using Plug and PlayAdd Printer Wizard appears Click Have DiskSetting Up Options Double-click the printer icon on the Windows Task Bar Canceling a Print JobOn the Document menu, click Cancel Printing Click Browse… Windows 3.1x Installing the IPDL-C Printer DriverInstalling the Printer Driver Tions dialog from an application Setting Up OptionsOn the Document menu, click Delete Document Click Have Disk… Windows NT4.0 Installing the IPDL-C Printer DriverClick the Installable Options tab Click OK to close the printer properties Paper Sizes Paper and Other Media Supported by this PrinterPaper Types and Sizes ⇒ P.52 Loading Paper in the Bypass Tray Paper types and cautions Plain paper Precautions for PaperAdhesive labels Thick PaperPaper not supported by this printer OHP transparenciesPrintable Area Load paper into the tray with the print side up Loading PaperLoading Paper in the Paper Tray Paper Size Standard Optional Tray Tray1 Tray2/3 Slide the paper tray completely into the printerReady5 Menu IPDL-C MenuTray Size* j 5x13 l Tray Size* j 25x13 lLoad paper until it stops with the print side down Loading Paper in the Bypass TrayOpen the bypass tray Slide the side guidesCustom Jl/# Width 297mm Media j 1.Paper Tray lPaper Tray j Tray1/A4 l Media j 2.Paper Size lPress Escape Sliding out the Output Tray ExtenderRepeat step B to set the value of the width Repeat steps B and C to set the value of the lengthPrinted Error Message Error & Status MessagesMessage Description Comments Error & Status Messages on the Operation Panel⇒ P.76 Removing Misfed Paper Menu Setting Up Options Message Description Comments Mshell Getting Printer Information over the NetworkPrinter Current Status After this message appears Placing the Waste Toner Bottle and Charger Printer Configuration Input Tray Status Input Tray NameInput Tray Paper Size Emulation Name Printer Doesnt Print Possible Cause SolutionsNetwork Connection If the printer is using I/O TimeoutClick Connect Windows 95/98Properties WindowsStatus Possible Causes, Descriptions, and Solutions Other Printing ProblemsIng Paper in the Paper Tray Charger and P.81 Cleaning the Dust-proofing glass Ing the Charger Or Setting tab Other Printing Problems Removing Misfed Paper Carefully pull the misfed paper When the Message Open Front Cover Remove Misfeed AppearsStandard Tray Tray1 or Paper Feed Unit Tray2/3 Bypass trayOpen the paper exit cover When the Message Remove Misfeed From Output Tray AppearsClose the front cover Close the paper exit cover Close the front cover Remove the misfed paper from inside of the printerRemove the misfed paper from the output tray Cleaning the Charger Cleaning and Adjusting the PrinterCleaning the Friction Pad Remove the cleaning brush from back of the front cover Cleaning the Dust-proofing glassMaintenance j 2.Toner Level l Adjusting the Image DensityMenu j Maintenance l Maintenance j 1.Toner SelectlMagenta jl/# ------g-----+ Adjusting the SettingList Print Config.Page TrayMenu List Print Menu MaintenanceMaintenance j 1.Toner Selectl Tray2W jl/# ------g-----+ Maintenance j 4.RegistrationlSlide the lock lever up Replacing ConsumablesAdd Toner Open the left coverPull the tape out as shown in the illustration Remove the protective sheet from the new toner cartridgeSlide the new toner cartridge into the printer Return the lock lever to its origi- nal positionSpecifying the replacing toner cartridge Toner Select j BlacklToner Select Please Wait Toner Select Add TonerChange PCU Turn off the printers power switchReplacing the Photoconductor Unit TFWX400E Add FuserOil Turn on the printer’s power switchReplacing the Fuser Oil Bottle and Ozone Filter Close the fuser oil bottle cover Remove the green cap from the new oil bottleInsert a new ozone filter into the printer Waste T Full Waste Toner isTFWX330E Push the right and left lock le- vers of the charger Replace the chargerMenu and Media setting priorities Setting MenusFollowing message appears on the panel display Setting MenusTray Size* j DLl Press On Line to enter the off-line condition Take Offline Then Press ResetTray Size* j LTl Protecting the Menus Use UT to display Maintenance, and then press EnterProtecting the Menus Menu Protect j Onl Changing the Menu Settings without Removing ProtectMaintenance j 5.Menu Protectl Menu Protect j OfflRemoving Protect Use UT to display Off, and then press Enter Menu Table System Menu Menu SettingsIPDL-C Menu ×13 O BufferParallel Energy LevelTransfer Image MemoryLanguage Bi-directionOHP Slip PrinterLangConfirm that Config.Page is on the display, press Enter Printing the ConfigurationList Print j Config.Page l Config.Page Press # keyPrinter Information Interpreting ConfigurationReference Status List Error LogUse UT to display Color Sample, and then press Enter Printing the Color SampleList Print j Color Sample l Color Sample Press # keyTurn on the printer’s power switch Press Menu Resetting MenusMaintenance j 5.Menu Reset l Menu Reset Press # key112 Memory Capacity and Paper Size Resolution 300 dpiResolution 600 dpi Low Memory Moving and Transporting the Printer Mainframe SpecificationsWarm-up Time Noise Emission Sound Power LevelDimensions WeightOptions Access Time Ieee 1284 Parallel Type305 ModeNumber of Pins Toner Cartridge ConsumablesOther Consumables Service Life *1Glossaries RPS2 Edge Smoothing Print PortPrinter Properties Proportional FontsIndex 125 126