Samsung ML-1615 manual Using Print Materials

Page 42

•Load transparencies in the tray with print side up, and the top with the adhesive strip going first.

3

Notes:

•To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are printed out.

•Place transparencies on a flat surface after removing them from the printer.

•Do not use transparencies that are separating from the backing sheet.

•Load card stock with print side up, short edge first and center of the tray.

•Load letterheads in the tray with the design face up, top edge towards the printer.

USING PRINT MATERIALS 3.9

Image 42

Contents ML-1610 Series About the User’s Guide Contact Samsung World Wide Latvia Contents Cleaning the Outside Cleaning the Inside Redistributing Toner Replacing the Toner CartridgeImportant Precautions and Safety Information 17SAVE These Instructions Environmental and Safety Consideration Ozone Safety Radio Frequency Emissions Declaration of Conformity European Countries Page Introduction Up to 16 ppm in A4 17 ppm in Letter Special FeaturesYou can print at 600 dots per inch dpi You can print in Windows 98/Me/2000/XPPrinter Driver Features Feature Printer DriverPrinter Components Front ViewRear View Understanding the Control Panel On Line/Error and Toner Save LEDsSee Troubleshooting Error Messages on DescriptionCancel button Function DescriptionSetting Up Your Printer Unpacking Paper Cover aComponents may differ from one country to another Selecting a Location Carefully remove all of packing tape from the printerClearance Space Installing the Toner Cartridge Grasp the front cover and pull it toward you to openSetting UP Your Printer Setting UP Your Printer Loading Paper You can load approximately 150 sheets of paper in the trayLoad paper with the print side facing up Connecting a Printer Cable Turning the Printer on Demo page shows the printer’s current configuration Printing a DemoInstalling Printer Software System RequirementsVarious Linux See Software User’s Guide Setting UP Your Printer Using Print Materials Choosing Paper and Other Materials Paper Type Capacitya Type and CapacitiesGuidelines for Paper and Special Materials Plain paperOnly use labels recommended for laser printers Using Print Materials Using the Tray Verifying the Output LocationUsing Manual Feed Mode Repeat this step for every page to be printedPrinting on Special Materials Using Print Materials Canceling a Print Job There are two ways to cancel a print jobPress the Cancel button on the control panel Double-click this icon to view Queue of the print jobs Maintaining Your Printer Maintaining the Toner Cartridge Toner cartridge storageRedistributing Toner Maintaining Your Printer Using the Toner Save Mode Replacing the Toner CartridgeCleaning the Printer Cleaning the OutsideCleaning the Inside Cleaning inside the printer Maintaining Your Printer Transfer Roller Consumables and Replacement PartsItems Yield Average Pick-up RollerSolving Problems Troubleshooting Checklist Check SolutionLine/Error LED is on Solving General Printing Problems Problem Possible Cause SolutionSoftware User’s Guide. Try printing a Text is wrong Garbled, orBut are blank Defective or out Toner Clearing Paper Jams Paper Exit AreaSolving Problems Paper Feed Area Around the Toner Cartridge Solving Print Quality Problems Print Quality ChecklistTips for Avoiding Paper Jams Solving Print Quality Problems Print4.6. Contact your service representative Scratched. Install a new toner cartridgeDirty. Clean the LSU. See Cleaning the Inside on Change to a lighter weight pages. See PaperProblem Solution Wrinkles or Black pagesCurl Poor Image qualityTroubleshooting Error Messages LED pattern Possible Problems and SolutionsToner cartridge and install a new one. See File in Use message Common Windows ProblemsProblem Possible Cause and Solution Appears duringCommon Linux Problems /etc/printcap fileThat would result in a cropped output Memory usage Am trying to print aRotated and cropped White nothing isYour software vendor to inform them of the issue Errors Owning the spooler daemon On my PCL or SPLError messages printing Able to printSpecifications Printer Specifications Paper SpecificationsPrinter Specifications Specifications and Description80 % RH Paper Specifications OverviewSize mm/in.a Weight Capacityb Supported Sizes of Paper60 to 165 g/m2 bond 16 to 43 lb Maximum size Legal Guidelines for Using Paper Symptom Problem with Solution PaperPaper Output Capacity Paper SpecificationsCategory Specifications Output Tray CapacityPrinter and Paper Storage Environment Index USB cable, connect Software User’s Guide Installing Printer Software in Windows Using Status Monitor Installing Printer Software in Windows Installing Printer Software in WindowsChoose the type of installation Changing the Software LanguageReinstalling Printer Software Removing Printer SoftwarePrinting a Document Basic PrintingSelect your printer driver from the Name drop-down list Orientation Printer SettingsLayout Tab Layout OptionsSize Paper TabCopies ScalingGraphics Tab ResolutionToner Save Mode DarknessExtras Tab About TabPrinter Tab Using a Favorite Setting Using HelpAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing a Reduced or Enlarged DocumentUsing Watermarks Using an Existing WatermarkFitting Your Document to a Selected Paper Size Deleting a Watermark Creating a WatermarkEditing a Watermark Watermark section. The Edit Watermark window appearsUsing Overlays What is an Overlay?Creating a New Page Overlay Using a Page Overlay Deleting a Page OverlayClick Delete Overlay Windows 9x/Me Setting Up a Host ComputerSetting Up a Client Computer Windows NT 4.0 or higherOpening the Troubleshooting Guide Using Status Monitor→ your printer driver name → Troubleshooting Guide Changing the Status Monitor Program Settings Following window opensSupported OS Using Your Printer in LinuxSystem Requirements Recommended CapacitiesInstalling the Printer Driver Changing the Printer Connection Method Using the Configuration Tool Uninstalling the Printer DriverSelect Complete uninstall and then click Uninstall Changing Llpr Properties Language, change 4 Layout properties, set Rev