Samsung ML-1700 specifications How to use DCU, DCU Setup

Page 52

ALIGNMENT & ADJUSTMENTS

66. Alignment and Adjustments

This chapter describes the main functions for service, such as the product maintenance method, the test output related to maintenance and repair, DCU using method, Jam removing method, and so on. It includes the contents of manual.

6.1 How to use DCU

6.1.1 DCU Setup

You can examine the malfunction of the printer. To perform DCU, open the front discharge cover and leave the connect the harness wire(10 pin/4 pin) to the CN3(ML-1750) or CN2(ML-1710/1510) of the Main control board.

ML SERIES DIAGNOSTIC CONTROL UNIT

STATUS

DIAGNOSTIC

04	DEV 300	DEV 350	DEV 350
05	LSU READY	LSU MT & LD	LSU MOTOR
07	PAPER EMPTY	PAPER WIDTH	NEW CRU
08		EXIT SENSOR	FEED SENSOR
09	COVER OPEN
10	COER HEATING	PRINTING TEMP	READY HEAT

ON

OFF

SELF TEST

DIAGNOSTIC CODE

00MAIN MOTOR OPERATING SYSTEM

01MAIN HIGH-VOLTAGE ON

02TRNSFER HIGH-VOLTAGE (-)ON

03THV(+) REFERANCE VOLTAGE

04DEV/SUPPLY HIGH-VOLTAGE ON/PTL ON

05LSU OPERATING SYSTEM

06PICKUP CLUTCH ON

07PEEMPTY/PWITH/NEW CRU TEST

08FEED & EXIT SENSOR TEST

09COVER OPEN SENSOR TEST

10FUSER TEST

11HOT BURN TEST

12CLEAN MODE PRINT

13THV(+)TRIGGER, ALL HV & FAN ON

14THV(+) REFERENCE ON

STATUS CODE

61 WARM UP

00READY (REGAL)

01READY (LETTER)

02READY (A4)

03READY (EXECUTIVE)

04READY (B5)

20 PRINT START

30FEED SENSOR ON

40FEED SENSOR OFF

50PAPER OUT

69 SLEEP MODE

ERROR STATUS CODE

60 OPEN FUSER ERROR

62LOW TEMPERATURE ERROR

68OVER HEATING ERROR

64COVER OPEN ERROR

70NO PAPERR

71PAPER JAM 0

72PAPER JAM 1

73PAPER JAM 2

95LSU NOT READY

DIAGNOSTIC		DOWN		SHIFT		STOP
DIAGNOSTIC		DOWN		SHIFT		STOP
MODE		UP				ENTER

TO ENTER DIAGNOSTIC MODE, PUSH THREE BUTTONS SIMUL ANEOUSL AND TURN THE PRINTER POWER ON.

Service Manual

Samsung Electronics

6-1

Image 52

Contents Precautions SpecificationsTroubleshooting Block DiagramElectronics 2003 Precautions Precaution related noxious material Precaution related electric shock or firePrecaution related handling the machine Precaution when assembly/disassemblyESD Precautions Tool for Troubleshooting DCUDiagnostic Control Unit DriverAcronyms and Abbreviations LSUSample Pattern for the Test 1 A4 5% Pattern2 A4 2% Pattern 3 A4 IDC Pattern Samsung Electronics Specifications General SpecificationsElectrical Specification Controller SpecificationEnvironmental Range Paper Handling Specifications Toner Cartridge DeveloperSpecifications Printer Components Front ViewRear View Inside ViewOn Line/Error and Toner Save LEDs Control PanelCancel button Printing demoSystem Layout FuserFeeding Part Transfer Ass’yDriver Ass’y Fixing PartFuserSafety Relevant Facts LSU Laser Scanner UnitToner Cartridge Main Pbaspl Model Asic Jupiter Flash MemorySdram Sensor input circuitPaper Feeding, Toner Cartridge Sensing Paper Exit SensingCover Open Sensing DC FAN / Solenoid DrivingMain PBA PCL Model Sdram Regulator Clock Generator Buffer Motor DriveML-1710 ML-1510 ML-1750 AsicSPGPm MemorySPGPm Internal Block Diagram AHB BUSSmps & Hvps HVPSHigh Voltage Power Supply SMPSSwitching Mode Power Supply Rated Power OutputConsumption Power Length of Power Cord 1830 ± 50mm Power Switch UseFuser AC Power Control Engine F/W DriveTransfer FeedingHeat Lamp Method FusingPID Method What is the Q-PID Method? 5 LSUReleasing Plastic Latches General Precautions on DisassemblyWhenever servicing the machine, you must perform as follows Top Cover Fuser FuserHeat Lamp TypeFuserQ-PID Type Unplug Thermister Harness from the Fuser cover Exit Roller LSUFan Driver Ass’yEngine Shield Ass’y Main PBASmps Transfer Roller Feed Roller Pick Up Roller & Solenoid How to use DCU DCU SetupCode Error CodeNormal Code Self Diagnostic Mode Code Description13 THV+ TRIGGER. ALL HV Self Test Button Functi on Enter Up/ Dow n Stop Remar kPaper Path Paper OutFace UpClearing Paper Jams Paper Exit Area JAM2Paper Feed Area JAM0 Around the Toner Cartridge JAM1Tips for Avoiding Paper Jams Sample Pattern Printing a DemoPrinting a cleaning sheet Consumables and Replacement Parts LED Status Display by Each ErrorPeriodic Defective Image Roller Defective image Typical defectSamsung Electronics Vertical Black Line and Band Bad imageVertical White Line Horizontal Black Band Black/White SpotLight Image Dark Image or a BlackUneven Density BackgroundGhost Satins on the Face Satins on Back Blank Page Print outWrong Print Position Bad discharge2 JAM 3 JAM 4 JAMMulti-Feeding Paper rolled in the FuserPaper rolled in the Toner Cartridge OPC Drum All LEDs blinking Scan Error All LEDs blinking Fuser ErrorMalfunction Paper Empty Not function of the gear of the fuser due to melting awayPaper Empty without indication No lamp on when the cover is open Cover OpenNo Power Defective motor operationVertical Line Getting Curved Toner Cartridge Service Precautions on Safe-keeping of Toner CartridgeService for the Life of Toner Cartridge Redistributing TonerSigns and Measures at Poor toner cartridge ImageFault Signs Cause & Check Solution White Black spot Bad Environment of The Software Printer is not workingUtilities program Abnormal Printing Spool Error How to delete the data in the spool managerExploded Views and Parts List 11-1 11-2 11-3 Main Assembly Parts List Unit Assembly Frame Unit Assembly Parts List Frame Unit Assembly Parts ListCont Drive Unit Assembly Drive Unit Assembly Parts ListCassette Unit Assembly Cassette Unit Assembly Parts List Fuser Unit Assembly Fuser Unit Assembly Parts List Samsung Electronics 9Block Diagram 9.1 PCL Model SPL Model Motor DR PART’SConnection Diagram PCL ModelComputer Schematic Diagrams PCL Main Circuit Diagram 1/7PCL Main Circuit Diagram 2/7 PCL Main Circuit Diagram 3/7 PCL Main Circuit Diagram 4/7 PCL Main Circuit Diagram 5/7 PCL Main Circuit Diagram 6/7 PCL Main Circuit Diagram 7/7 SPL Main Circuit Diagram 1/5 SPL Main Circuit Diagram 2/5 SPL Main Circuit Diagram 3/5 SPL Main Circuit Diagram 4/5 SPL Main Circuit Diagram 5/5 Hvps Circuit Diagram 1/2 THVHvps Circuit Diagram 2/2 4KVSmps Circuit Diagram 110V 1/2 Smps Circuit Diagram 110V 2/2 CON2-14MANUAL CON2-25EXIT