Samsung ML-1700 Toner Cartridge Service, Precautions on Safe-keeping of Toner Cartridge

Page 82

T RO U B L E S H O OT I N G

7.4 Toner Cartridge Service

It is not guaranteed for the default caused by using other toner cartridge other than the cartridge supplied by the Samsung Electronic or caused by non-licensed refill production.

7.4.1 Precautions on Safe-keeping of Toner Cartridge

Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.

7.4.2 Service for the Life of Toner Cartridge

If the printed image is light due to the life of the toner, you can temporarily improve the print quality by redistributing the toner(Shake the toner cartridge), however, you should replace the toner cartridge to solve the problem thoroughly.

7.4.3 Redistributing Toner

When toner is low, faded or light areas may appear on a printed page. You may be able to temporarily improve the print quality by redistributing the toner. The following procedures may allow you to finish the current print job before replacing the toner cartridge.

1)Grasp the front cover and pull it toward you to open.

2)Remove the toner cartridge from the printer

3)Gently shake the toner cartridge from side to side five or six times to redistribute the toner.

Note :

If the toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric.

Note :

Avoid reaching too far into the printer. The fusing area may be hot.

To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes.

4)Reinsert the toner cartridge into the printer. Ensure that the toner cartridge snaps into place.

5)Close the front cover. Make sure that the cover is securely closed.

1.7

Service Manual

Samsung Electronics

7-17

Image 82

Contents Troubleshooting PrecautionsSpecifications Block DiagramElectronics 2003 Precautions Precaution related noxious material Precaution related electric shock or firePrecaution related handling the machine Precaution when assembly/disassemblyESD Precautions Tool for Troubleshooting DCUDiagnostic Control Unit DriverAcronyms and Abbreviations LSUSample Pattern for the Test 1 A4 5% Pattern2 A4 2% Pattern 3 A4 IDC Pattern Samsung Electronics Specifications General SpecificationsElectrical Specification Controller SpecificationEnvironmental Range Paper Handling Specifications Toner Cartridge DeveloperSpecifications Printer Components Front ViewRear View Inside ViewOn Line/Error and Toner Save LEDs Control PanelCancel button Printing demoSystem Layout FuserDriver Ass’y Feeding PartTransfer Ass’y Fixing PartFuserSafety Relevant Facts LSU Laser Scanner UnitToner Cartridge Main Pbaspl Model Sdram Asic JupiterFlash Memory Sensor input circuitCover Open Sensing Paper Feeding, Toner Cartridge SensingPaper Exit Sensing DC FAN / Solenoid DrivingMain PBA PCL Model Sdram Regulator Clock Generator Buffer Motor DriveML-1710 ML-1510 ML-1750 AsicSPGPm MemorySPGPm Internal Block Diagram AHB BUSSmps & Hvps HVPSHigh Voltage Power Supply Consumption Power SMPSSwitching Mode Power SupplyRated Power Output Length of Power Cord 1830 ± 50mm Power Switch UseFuser AC Power Control Transfer Engine F/WDrive FeedingHeat Lamp Method FusingPID Method What is the Q-PID Method? 5 LSUReleasing Plastic Latches General Precautions on DisassemblyWhenever servicing the machine, you must perform as follows Top Cover Fuser FuserHeat Lamp TypeFuserQ-PID Type Unplug Thermister Harness from the Fuser cover Exit Roller LSUFan Driver Ass’yEngine Shield Ass’y Main PBASmps Transfer Roller Feed Roller Pick Up Roller & Solenoid How to use DCU DCU SetupCode Error CodeNormal Code Self Diagnostic Mode Code Description13 THV+ TRIGGER. ALL HV Self Test Button Functi on Enter Up/ Dow n Stop Remar kPaper Path Paper OutFace UpClearing Paper Jams Paper Exit Area JAM2Paper Feed Area JAM0 Around the Toner Cartridge JAM1Tips for Avoiding Paper Jams Sample Pattern Printing a DemoPrinting a cleaning sheet Consumables and Replacement Parts LED Status Display by Each ErrorPeriodic Defective Image Roller Defective image Typical defectSamsung Electronics Vertical Black Line and Band Bad imageVertical White Line Horizontal Black Band Black/White SpotLight Image Dark Image or a BlackUneven Density BackgroundGhost Satins on the Face Satins on Back Blank Page Print outWrong Print Position Bad discharge2 JAM 3 JAM 4 JAMMulti-Feeding Paper rolled in the FuserPaper rolled in the Toner Cartridge OPC Drum All LEDs blinking Scan Error All LEDs blinking Fuser ErrorMalfunction Paper Empty Not function of the gear of the fuser due to melting awayPaper Empty without indication No lamp on when the cover is open Cover OpenNo Power Defective motor operationVertical Line Getting Curved Service for the Life of Toner Cartridge Toner Cartridge ServicePrecautions on Safe-keeping of Toner Cartridge Redistributing TonerSigns and Measures at Poor toner cartridge ImageFault Signs Cause & Check Solution White Black spot Bad Environment of The Software Printer is not workingUtilities program Abnormal Printing Spool Error How to delete the data in the spool managerExploded Views and Parts List 11-1 11-2 11-3 Main Assembly Parts List Unit Assembly Frame Unit Assembly Parts List Frame Unit Assembly Parts ListCont Drive Unit Assembly Drive Unit Assembly Parts ListCassette Unit Assembly Cassette Unit Assembly Parts List Fuser Unit Assembly Fuser Unit Assembly Parts List Samsung Electronics 9Block Diagram 9.1 PCL Model SPL Model Motor DR PART’SConnection Diagram PCL ModelComputer Schematic Diagrams PCL Main Circuit Diagram 1/7PCL Main Circuit Diagram 2/7 PCL Main Circuit Diagram 3/7 PCL Main Circuit Diagram 4/7 PCL Main Circuit Diagram 5/7 PCL Main Circuit Diagram 6/7 PCL Main Circuit Diagram 7/7 SPL Main Circuit Diagram 1/5 SPL Main Circuit Diagram 2/5 SPL Main Circuit Diagram 3/5 SPL Main Circuit Diagram 4/5 SPL Main Circuit Diagram 5/5 Hvps Circuit Diagram 1/2 THVHvps Circuit Diagram 2/2 4KVSmps Circuit Diagram 110V 1/2 Smps Circuit Diagram 110V 2/2 CON2-14MANUAL CON2-25EXIT