Samsung ML-4050N manual Setting the memory in the PostScript printer properties

Page 60

3Grasp the control board cover and remove it.

4Completely open the latches on each side of the DIMM slot.

5Remove the memory DIMM from its antistatic package. Locate the alignment notches on the bottom edge of the DIMM.

Notches

Connection

Points

6Holding the memory DIMM by the edges, align the notches on the memory DIMM with the grooves on the memory DIMM slot.

7Push the DIMM straight into the DIMM slot until it snaps into place. Make sure the latches fit over the notches located on either side of the DIMM.

Latch

8Close the control board cover by aligning the groove on it with the notch on the printer and sliding it.

9Reinstall the duplex-slot cover or the duplex unit.

10Reconnect the power cord and printer cable, and turn the printer on.

Setting the memory in the PostScript printer properties

After installing the DIMM, you need to select it in the printer properties of the PostScript printer driver to enable its use.

1Make sure that the PostScript printer driver is installed on your computer. To install the PostScript printer driver, see the Software section.

2Click the Windows Start menu.

3For Windows 98/Me/NT 4.0/2000, select Settings and then Printers.

For Windows XP/2003, select Printers and Faxes.

For Windows Vista, select Control Panel → Hardware and Sound → Printers.

4Select the Samsung ML-4050 Series PS printer.

5Click the right mouse button on the printer icon and select Properties.

6For Windows 98/Me, select the Device Option tab.

For Windows NT 4.0/2000/XP/2003/Vista, select the Device Settings tab.

7Select the amount of memory you installed from Printer Memory in the Installable Options section.

For Windows 98, select Installable Options → VMOption → change setting for:NMOption → change memory.

8Click OK.

10.2 <Installing accessories>

Image 60

Contents Page Page Contact Samsung World Wide Country Customer Care Center Web SiteContents Troubleshooting Installing accessoriesSpecifications Safety and Regulatory Information Important Precautions and Safety InformationEnvironmental and Safety Consideration Laser Safety StatementOzone Safety Power SaverRecycling Radio Frequency EmissionsUnited States of America Declaration of Conformity European CountriesWireless Guidance Regulatory Compliance StatementsReplacing the Fitted Plug for UK Only D e c la r a tio n o f Co n fo r m ity R & T T E Special features IntroductionYou can print in Windows 98/Me/NT 4.0/2000/XP 2003/VistaMacintosh Printer overview Front viewFinding more information Control panel overviewSelecting a location Clearance spaceSystem setup Using control panel menusAccessing control panel menus Menu overview Job manager menuInformation menu Layout menu Paper menuSystem Setup menu Graphic menuEmulation menu PostScriptUsing toner save mode Printing a demoChanging the display language Software overview Supplied softwarePrinter driver features System requirementsWindows Linux MacintoshRequirements Network setup Via network administration programsVia the control panel Configuring TCP/IP Configuring EtherTalkDynamic addressing BOOTP/DHCP Supported operating systemsConfiguring IPX frame types Setting Ethernet speedRestoring the network configuration Printing a network configurationLoading print media Selecting print mediaType Size Dimensions Weighta Capacityb Type Size WeightSupported sizes of paper Print media for duplex printingGuidelines for selecting and storing print media Guidelines for special print mediaMedia type Guidelines Loading paper Using the standard tray or the optional trays Changing the size of the paper in the trayUsing the multi-purpose tray Load the paper with the side to be printed on facing upUsing manual feed mode Tips on using the multi-purpose traySelecting an output location Printing to the output tray Face downPrinting to the rear cover Face up Canceling a print job Printing a document Canceling a print jobBasic printing Printing a documentOrdering supplies and accessories AccessoriesToner cartridges How to purchase Maintenance Cleaning the printerCleaning the outside of the printer Cleaning the inside of the printerPTL lens Maintaining the toner cartridge Checking the remaining tonerRedistributing toner cartridge Replacing the toner cartridge Maintenance Maintenance parts Items Yield AverageTroubleshooting Clearing paper jamsPaper feed area TrayOptional tray Around the toner cartridge Multi-purpose trayPaper exit area Duplex unit areaDuplex jam Troubleshooting checklist Condition Suggested solutionsTips for avoiding paper jams Understanding the status LED Understanding display messagesMessage Meaning Suggested solutions Load Low Heat ErrorLSU Motor Error OPC is CleaningToner cartridge-related messages Solving general printing problems Settings and Printers. Right Spool Settings buttonClick the Samsung ML-4050 Series PCL 6 printer iconSolving print quality problems Condition Suggested solutions Vertical Condition Suggested solutions Curl or waveRepetitive DefectsCommon Windows problems Common PostScript problemsCommon Linux problems Common Macintosh problemsInstallable Options section to InstalledInstalling accessories Precautions when installing accessoriesInstalling a memory Dimm Disconnect the power cordSetting the memory in the PostScript printer properties Installing a wireless network interface card Removing a DimmConfiguring the wireless network parameters Selecting the authentication typeConfiguring basic network settings Using the hard disk Installing the hard diskSetting Encryption Restoring default values for wireless networkingSetting the hard disk in the printer properties Setting the time and datePrinting with the optional hard disk Storing a jobPrinting a stored job Deleting a stored jobControlling the active job queue To delete a file from the queuePrinting using the form files To promote a file from the queueTo print a file immediately Specifications Printer specificationsSpecifications and Description Index System requirements Linux 3.3 Macintosh 3.3 Windows Software section Contents Using Windows Postscript Driver Using Your Printer in Linux Installing Printer Software Installing Software for Local PrintingTypical Installation Custom Installation Select Typical installation for a local printer. Click NextSelect Custom installation. Click Next Select the components to be installed and click NextInstalling Software for Network Printing Custom Installation Select Custom installation. Click Next Reinstalling Printer Software Changing the Software LanguageSelect the components you want to reinstall and click Next Removing Printer SoftwarePrinting a Document Select your printer driver from the Name drop-down listPrinter Settings Layout TabPaper Orientation Paper Tab SourceScaling Printing Image Mode ResolutionToner Save Mode Graphics TabJob Setting On the Job SettingExtras Tab Using a Favorite Setting Using HelpAbout Tab Printer TabAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing BookletsPrinting on Both Sides of Paper Printing a Reduced or Enlarged DocumentFitting Your Document to a Selected Paper Size NoneUsing Watermarks Using an Existing WatermarkCreating a Watermark Editing a WatermarkUsing Overlays What is an Overlay?Using a Page Overlay Creating a New Page OverlayUsing Windows PostScript Driver AdvancedUsing the shortcut icon Using the right-click menuOverview Direct Print Utility PrintingSetting Up a Host Computer Setting Up a Client ComputerCheck the Share this printer box Select Local Port and click New PortTroubleshooting Guide Printer SettingUnderstanding Smart Panel Toner LevelOpening the Troubleshooting Guide Changing the Smart Panel Program SettingsUsing Printer Settings Utility Using Onscreen Help FileInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Uninstalling the Unified Linux Driver Click UninstallUsing the Unified Driver Configurator Printers ConfigurationOpening the Unified Driver Configurator Double-clickUnified Driver Configurator on the desktopConfiguring Printer Properties Ports ConfigurationClasses Tab Printing from Applications Printing FilesFile menu Installing Software for Macintosh Click ContinueSetting Up the Printer For a Network-connected MacintoshFor a USB-connected Macintosh Mac OS 8.6 ~Changing Printer Settings Layout SettingPrinting a Document Printer Features Setting ResolutionQualityPrinting Multiple Pages on One Sheet of Paper Reverse DuplexDuplex Printing Index Resolution Macintosh 36 Windows GGGGGGGGGGGGGRev.1.01