Samsung ML-3470 Series manual Configuring TCP/IP, Using SetIP program, Static addressing

Page 27

Configuring TCP/IP

Your printer can be set up with a variety of TCP/IP network information, such as an IP address, a subnet mask, a gateway, and DNS addresses. There are several ways in which your printer can be assigned a TCP/IP address, depending on your network.

•Static addressing: A TCP/IP address is assigned manually by the system administrator.

•Dynamic addressing via BOOTP/DHCP (default): A TCP/IP address is assigned automatically by the server.

Note

Before configuring TCP/IP, you need to set the network protocol to TCP/IP.

Static addressing

To enter a TCP/IP address from your printer’s control panel, take the following step:

1Press Menu until Network appears on the bottom line of the display and press OK.

2Press OK when TCP/IP appears.

3Press the scroll buttons until Static appears and press OK.

4Press OK when IP Address appears.

5Set the first byte between 0 and 255 using the scroll buttons and press OK to move to the next byte.

Repeat this to complete the address from the 1st byte to the 4th byte.

6When you have finished, press OK.

7Repeat step 5 and 6 to configure the other TCP/IP parameters: subnet mask and gateway address.

8Press Stop to return to Standby mode.

Dynamic addressing (BOOTP/DHCP)

To have a TCP/IP address assigned automatically by the server, take the following step:

1Press Menu until Network appears on the bottom line of the display.

2Press OK when TCP/IP appears.

3Press the scroll buttons until DHCP or BOOTP appears and press OK.

4Press Stop to return to Standby mode.

Using SetIP program

This program is for the network IP setting using the MAC address which is the hardware serial number of the network printer card or interface. Especially, it is for the network administrator to set several network IPs at the same time.

1Insert the driver CD provided along with your machine.

2Start Windows Explorer and open the X drive. (X represents your CD-ROM drive.)

3Double click Application > SetIP.

4Open the language folder you want to use.

5Double click Setup.exe to install this program.

6From the Windows Start menu, select Programs > Samsung Network Printer Utilities > SetIP.

7Select the name of your printer and click " ".

Note

If you cannot find your printer name click " " to refresh the list.

8Enter the network card's MAC address, IP address, subnet mask, default gateway, and then click Apply.

Note

If you do not know the network card's MAC address, print the machine's network information report.

9Click OK to confirm the settings.

10Click Exit to close the SetIP program.

Note

If you are in a non-static IP address environment and need to setup a DHCP network protocol, go to the http:// developer.apple.com/networking/bonjour/download/, select the program Bonjour for Windows due to your computer operating system, and install the program. This program will allow you to fix the network parameter automatically. Follow the instruction in the installation window. This program does not support Linux.

4.2 <Network setup(ML-3471ND only)>

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Page Page Contact Samsung worldwide Spain Contents Installing accessories Ordering supplies and accessoriesMaintenance TroubleshootingLaser Safety Statement Safety and Regulatory InformationImportant Precautions and Safety Information Environmental and Safety ConsiderationRadio Frequency Emissions Ozone SafetyPower Saver RecyclingDeclaration of Conformity European Countries United States of AmericaWireless Guidance Regulatory Compliance StatementsReplacing the Fitted Plug for UK Only Declaration of Conformity You can print in Windows 2000/XP/2003/Vista Special featuresSpecial features Printer overview Finding more information IntroductionFeatures ML-3470D ML-3471ND Printer overviewFront view Rear view Control panel overviewML-3470D and ML-3471ND Finding more information Understanding the Status LEDClearance space Altitude adjustmentClick Printer Setting Selecting a locationMenu overview System setupUsing control panel menus Accessing control panel menusLayout menu Information menuSystem Setup menu Paper menuGraphic menu PostScript Emulation menuUsing toner save mode Printing a demoChanging the display language Changing the font setting Supplied software Software overviewPrinter driver features System requirementsWindows Linux MacintoshRequirements Via network administration programs Supported operating systemsVia the control panel Static addressing Configuring TCP/IPUsing SetIP program Dynamic addressing BOOTP/DHCPPrinting a network configuration Configuring EtherTalkSetting Ethernet speed Restoring the network configurationSelecting print media Loading print mediaSupported sizes of paper Type Size Dimensions Weighta CapacitybGuidelines for selecting and storing print media Guidelines for special print mediaMedia type Guidelines Loading paper Changing the size of the paper in the tray Using the tray 1 or the optional trayLoad the paper with the side to be printed on facing up Using the multi-purpose trayTips on using the multi-purpose tray Using manual feed modeSelecting an output location Printing to the output tray Face downPrinting to the rear cover Face up Printing a document Canceling a print jobPrinting a document Canceling a print job Basic printingToner cartridges Ordering supplies and accessoriesAccessories How to purchaseCleaning the inside of the printer MaintenanceCleaning the printer Cleaning the outside of the printerChecking the remaining toner Maintaining the toner cartridgeOpen the front cover Pull the toner cartridge out Redistributing toner cartridgeReplacing the toner cartridge Toner Low appears on the displayMaintenance parts Clearing the Toner Low Replace Toner messageItems Yield Average Tray TroubleshootingClearing paper jams Paper feed areaMulti-purpose tray Optional trayPaper exit area Around the toner cartridgeDuplex jam Duplex unit areaTips for avoiding paper jams Understanding display messages Troubleshooting checklistSelf Diagnostic Message Meaning Suggested solutions LSU Motor ErrorOpen Heat Error Over Heat ErrorToner cartridge-related messages Solving general printing problems Select Download as Bit Image Advanced OptionsTurn on Print As Image from Solving print quality problems Skew ScatterMisformed CharactersOption through Printer Settings Utility or Printer Common Windows problemsCommon PostScript problems Condition Suggested solutions CurlCommon Macintosh problems Common Linux problemsDisconnect the power cord Installing accessoriesPrecautions when installing accessories Installing a memory DimmInstalling a wireless network interface card Setting the memory in the PostScript printer propertiesSelect the Samsung ML-3470 Series printer Configuring basic network settings Configuring the wireless network parametersHexadecimal Alphanumeric Selecting the authentication typeSetting Encryption Restoring default values for wireless networkingSpecifications and Description SpecificationsPrinter specifications Printer specificationsIndex Page Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Select Typical installation for a local printer. Click Next Installing Printer SoftwareInstalling Software for Local Printing Typical InstallationCustom Installation Select the components to be installed and click Next Select Custom installation. Click NextInstalling Software for Network Printing Custom Installation Installing Printer Software in Windows Select the components you want to reinstall and click Next Reinstalling Printer SoftwareNext Removing Printer SoftwareSelect your printer driver from the Name drop-down list Printing a DocumentPrinter Settings Printing to a file PRNSelect Printers and Faxes Select your printer driver icon Layout Tab Paper TabPaper Orientation Scaling Printing Image ModeGraphics Tab SourceOverlay Extras TabAdvanced Options WatermarkPrinter Tab Using a Favorite SettingUsing Help About TabPrinting Multiple Pages on One Sheet of Paper N-Up Printing Advanced PrintingPrinting Booklets Printing PostersNone Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document Fitting Your Document to a Selected Paper SizeEditing a Watermark Using WatermarksUsing an Existing Watermark Creating a WatermarkCreating a New Page Overlay Using OverlaysWhat is an Overlay? Using a Page OverlayAdvanced Using Windows PostScript DriverDouble-clickPrinters and Faxes Setting Up a Host ComputerSetting Up a Client Computer Check the Share this printer boxToner Level Understanding Smart PanelUsing Onscreen Help File Opening the Troubleshooting GuideUsing Printer Settings Utility Changing the Smart Panel Program SettingsInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Click Uninstall Uninstalling the Unified Linux DriverDouble-clickUnified Driver Configurator on the desktop Using the Unified Driver ConfiguratorPrinters Configuration Opening the Unified Driver ConfiguratorConfiguring Printer Properties Ports ConfigurationClasses Tab Printing Files Printing from ApplicationsPrinter driver Installing SoftwareInstalling the printer driver Uninstalling the printer driverMac OS 8.6 ~ Setting Up the PrinterFor a Network-connected For a USB-connectedLayout Changing Printer SettingsPrinting Printing a DocumentPrinter Features GraphicsPaper Duplex Printing Printing Multiple Pages on One Sheet of PaperIndex Favorites 17 image mode 15 resolution GGGGGGGGGGGGGRev
Top Page Image Contents