Samsung ML-3470 Series manual Configuring the wireless network parameters

Page 59

4Replace the control board cover.

5Reconnect the power cord and turn the printer on.

Note

You can also configure the network parameters on the control panel; see the next column.

Configuring the wireless network parameters

After installing the wireless network card, you must configure the appropriate network parameters to use your printer in a wireless network. To do this, you can use both control panel and SyncThru Web Service, an embedded web site of your printer. This section gives you basic information on 802.11b/g network parameters which can be configured from the control panel.

Configuring basic network settings

You can configure basic wireless settings, such as SSID, Operation Mode, and channels. You can retrieve basic settings by selecting a wireless network or manually configure them as you need.

1Press Menu until Network appears on the bottom line of the display and press OK.

2Press the scroll buttons until Wireless appears and press OK.

3Press OK when WLAN Basic appears.

4Press the scroll buttons to select the setup method you want and press OK.

•Search List: The wireless network interface card on your printer searches for wireless networks in the area and shows the results.

•Custom: You can configure the wireless settings according to your needs.

5If you selected Search List, press the scroll buttons to select a network and press OK.

If you selected Custom, set each network options:

•Edit SSID: Enter the SSID, the name that identifies a wireless network. SSID is case-sensitive so you need to enter it.

•Operation Mode: Select the type of wireless connections.

In Ad-Hocmode, wireless cards communicate directly each other.

In Infrastructure mode, network cards communicate with each other through an access point, which allows both wireless and cabled cards to send files to the printer. If you select Auto, the printer selects the operation mode automatically, according to the network cable’s connection each time it boots up.

Note

In Ad-Hocmode, even if the network cable is connected, your printer will use the wireless interface.

•Channel: This option is available only in the Ad-Hoc mode. In most cases, you will not need to change this setting. The printer will scan all available channels for the specified network and will adapt its channel to the one detected.

6When you have finished, press Stop to return to Standby mode.

10.3 <Installing accessories>

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Page Page Contact Samsung worldwide Spain Contents Installing accessories Ordering supplies and accessoriesMaintenance TroubleshootingLaser Safety Statement Safety and Regulatory InformationImportant Precautions and Safety Information Environmental and Safety ConsiderationRadio Frequency Emissions Ozone SafetyPower Saver RecyclingDeclaration of Conformity European Countries United States of AmericaReplacing the Fitted Plug for UK Only Wireless GuidanceRegulatory Compliance Statements Declaration of Conformity You can print in Windows 2000/XP/2003/Vista Special featuresSpecial features Printer overview Finding more information IntroductionFront view Features ML-3470D ML-3471NDPrinter overview ML-3470D and ML-3471ND Rear viewControl panel overview Finding more information Understanding the Status LEDClearance space Altitude adjustmentClick Printer Setting Selecting a locationMenu overview System setupUsing control panel menus Accessing control panel menusLayout menu Information menuGraphic menu System Setup menuPaper menu PostScript Emulation menuChanging the display language Using toner save modePrinting a demo Changing the font setting Supplied software Software overviewWindows Printer driver featuresSystem requirements Requirements LinuxMacintosh Via the control panel Via network administration programsSupported operating systems Static addressing Configuring TCP/IPUsing SetIP program Dynamic addressing BOOTP/DHCPPrinting a network configuration Configuring EtherTalkSetting Ethernet speed Restoring the network configurationSelecting print media Loading print mediaSupported sizes of paper Type Size Dimensions Weighta CapacitybMedia type Guidelines Guidelines for selecting and storing print mediaGuidelines for special print media Loading paper Changing the size of the paper in the tray Using the tray 1 or the optional trayLoad the paper with the side to be printed on facing up Using the multi-purpose trayTips on using the multi-purpose tray Using manual feed modePrinting to the rear cover Face up Selecting an output locationPrinting to the output tray Face down Printing a document Canceling a print jobPrinting a document Canceling a print job Basic printingToner cartridges Ordering supplies and accessoriesAccessories How to purchaseCleaning the inside of the printer MaintenanceCleaning the printer Cleaning the outside of the printerChecking the remaining toner Maintaining the toner cartridgeOpen the front cover Pull the toner cartridge out Redistributing toner cartridgeReplacing the toner cartridge Toner Low appears on the displayItems Yield Average Maintenance partsClearing the Toner Low Replace Toner message Tray TroubleshootingClearing paper jams Paper feed areaMulti-purpose tray Optional trayPaper exit area Around the toner cartridgeDuplex jam Duplex unit areaTips for avoiding paper jams Understanding display messages Troubleshooting checklistSelf Diagnostic Message Meaning Suggested solutions LSU Motor ErrorOpen Heat Error Over Heat ErrorToner cartridge-related messages Solving general printing problems Turn on Print As Image from Select Download as Bit ImageAdvanced Options Solving print quality problems Skew ScatterMisformed CharactersOption through Printer Settings Utility or Printer Common Windows problemsCommon PostScript problems Condition Suggested solutions CurlCommon Macintosh problems Common Linux problemsDisconnect the power cord Installing accessoriesPrecautions when installing accessories Installing a memory DimmSelect the Samsung ML-3470 Series printer Installing a wireless network interface cardSetting the memory in the PostScript printer properties Configuring basic network settings Configuring the wireless network parametersHexadecimal Alphanumeric Selecting the authentication typeSetting Encryption Restoring default values for wireless networkingSpecifications and Description SpecificationsPrinter specifications Printer specificationsIndex Page Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Select Typical installation for a local printer. Click Next Installing Printer SoftwareInstalling Software for Local Printing Typical InstallationCustom Installation Select the components to be installed and click Next Select Custom installation. Click NextInstalling Software for Network Printing Custom Installation Installing Printer Software in Windows Select the components you want to reinstall and click Next Reinstalling Printer SoftwareNext Removing Printer SoftwareSelect your printer driver from the Name drop-down list Printing a DocumentSelect Printers and Faxes Select your printer driver icon Printer SettingsPrinting to a file PRN Paper Orientation Layout TabPaper Tab Scaling Printing Image ModeGraphics Tab SourceOverlay Extras TabAdvanced Options WatermarkPrinter Tab Using a Favorite SettingUsing Help About TabPrinting Multiple Pages on One Sheet of Paper N-Up Printing Advanced PrintingPrinting Booklets Printing PostersNone Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document Fitting Your Document to a Selected Paper SizeEditing a Watermark Using WatermarksUsing an Existing Watermark Creating a WatermarkCreating a New Page Overlay Using OverlaysWhat is an Overlay? Using a Page OverlayAdvanced Using Windows PostScript DriverDouble-clickPrinters and Faxes Setting Up a Host ComputerSetting Up a Client Computer Check the Share this printer boxToner Level Understanding Smart PanelUsing Onscreen Help File Opening the Troubleshooting GuideUsing Printer Settings Utility Changing the Smart Panel Program SettingsGetting Started Installing the Unified Linux DriverInstalling the Unified Linux Driver Click Uninstall Uninstalling the Unified Linux DriverDouble-clickUnified Driver Configurator on the desktop Using the Unified Driver ConfiguratorPrinters Configuration Opening the Unified Driver ConfiguratorClasses Tab Configuring Printer PropertiesPorts Configuration Printing Files Printing from ApplicationsPrinter driver Installing SoftwareInstalling the printer driver Uninstalling the printer driverMac OS 8.6 ~ Setting Up the PrinterFor a Network-connected For a USB-connectedLayout Changing Printer SettingsPrinting Printing a DocumentPaper Printer FeaturesGraphics Duplex Printing Printing Multiple Pages on One Sheet of PaperIndex Favorites 17 image mode 15 resolution GGGGGGGGGGGGGRev
Top Page Image Contents