Samsung ML-3470D manual Configuring TCP/IP, Using SetIP program, Static addressing

Page 26

Configuring TCP/IP

Your printer can be set up with a variety of TCP/IP network information, such as an IP address, a subnet mask, a gateway, and DNS addresses. There are several ways in which your printer can be assigned a TCP/IP address, depending on your network.

•Static addressing: A TCP/IP address is assigned manually by the system administrator.

•Dynamic addressing via BOOTP/DHCP (default): A TCP/IP address is assigned automatically by the server.

Note

Before configuring TCP/IP, you need to set the network protocol to TCP/IP.

Static addressing

To enter a TCP/IP address from your printer’s control panel, take the following step:

1Press Menu until Network appears on the bottom line of the display and press OK.

2Press OK when TCP/IP appears.

3Press the scroll buttons until Static appears and press OK.

4Press OK when IP Address appears.

5Set the first byte between 0 and 255 using the scroll buttons and press OK to move to the next byte.

Repeat this to complete the address from the 1st byte to the 4th byte.

6When you have finished, press OK.

7Repeat step 5 and 6 to configure the other TCP/IP parameters: subnet mask and gateway address.

8Press Stop to return to Standby mode.

Dynamic addressing (BOOTP/DHCP)

To have a TCP/IP address assigned automatically by the server, take the following step:

1Press Menu until Network appears on the bottom line of the display.

2Press OK when TCP/IP appears.

3Press the scroll buttons until DHCP or BOOTP appears and press OK.

4Press Stop to return to Standby mode.

Using SetIP program

This program is for the network IP setting using the MAC address which is the hardware serial number of the network printer card or interface. Especially, it is for the network administrator to set several network IPs at the same time.

1Insert the driver CD provided along with your machine.

2Start Windows Explorer and open the X drive. (X represents your CD-ROM drive.)

3Double click Application > SetIP.

4Open the language folder you want to use.

5Double click Setup.exe to install this program.

6From the Windows Start menu, select Programs > Samsung Network Printer Utilities > SetIP.

7Select the name of your printer and click " ".

Note

If you cannot find your printer name click " " to refresh the list.

8Enter the network card's MAC address, IP address, subnet mask, default gateway, and then click Apply.

Note

If you do not know the network card's MAC address, print the machine's network information report.

9Click OK to confirm the settings.

10Click Exit to close the SetIP program.

Note

If you are in a non-static IP address environment and need to setup a DHCP network protocol, go to the http:// developer.apple.com/networking/bonjour/download/, select the program Bonjour for Windows due to your computer operating system, and install the program. This program will allow you to fix the network parameter automatically. Follow the instruction in the installation window. This program does not support Linux.

4.2 <Network setup(ML-3471ND only)>

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Page Page Contact Samsung worldwide Slovakia Contents Troubleshooting Ordering supplies and accessoriesMaintenance Installing accessoriesEnvironmental and Safety Consideration Safety and Regulatory InformationImportant Precautions and Safety Information Laser Safety StatementRecycling Ozone SafetyPower Saver Radio Frequency EmissionsUnited States of America Declaration of Conformity European CountriesReplacing the Fitted Plug for UK Only Wireless GuidanceRegulatory Compliance Statements Introduction Special featuresSpecial features Printer overview Finding more information Software SectionFront view Features ML-3470D ML-3471NDPrinter overview ML-3470D and ML-3471ND Rear viewControl panel overview Understanding the Status LED Finding more informationSelecting a location Altitude adjustmentClick Printer Setting Clearance spaceAccessing control panel menus System setupUsing control panel menus Menu overviewInformation menu Layout menuGraphic menu System Setup menuPaper menu Emulation menu PostScriptChanging the display language Using toner save modePrinting a demo Changing the font setting Software overview ContentsPrinter Settings Utility This program is Supplied softwareSystem requirements Printer driver featuresFeature WindowsRequirements LinuxMacintosh Via the control panel Via network administration programsSupported operating systems Dynamic addressing BOOTP/DHCP Configuring TCP/IPUsing SetIP program Static addressingRestoring the network configuration Configuring EtherTalkSetting Ethernet speed Printing a network configurationLoading print media Selecting print mediaType Size Dimensions Weighta Capacityb Supported sizes of paperMedia type Guidelines Guidelines for selecting and storing print mediaGuidelines for special print media Loading paper Using the tray 1 or the optional tray Changing the size of the paper in the trayUsing the multi-purpose tray Load the paper with the side to be printed on facing upUsing manual feed mode Tips on using the multi-purpose trayPrinting to the rear cover Face up Selecting an output locationPrinting to the output tray Face down Basic printing Canceling a print jobPrinting a document Canceling a print job Printing a documentHow to purchase Ordering supplies and accessoriesAccessories Toner cartridgesCleaning the outside of the printer MaintenanceCleaning the printer Cleaning the inside of the printerMaintaining the toner cartridge Saving Toner Checking the remaining tonerRedistributing toner cartridge Toner Low appears on the displayReplacing the toner cartridge Toner Low Replace Toner appears on the displayItems Yield Average Maintenance partsClearing the Toner Low Replace Toner message Paper feed area TroubleshootingClearing paper jams TrayOptional tray Multi-purpose trayAround the toner cartridge Paper exit areaDuplex unit area Duplex jamTips for avoiding paper jams Troubleshooting checklist Understanding display messagesOver Heat Error Message Meaning Suggested solutions LSU Motor ErrorOpen Heat Error Self DiagnosticToner cartridge-related messages Select Samsung ML-3470 Solving general printing problemsCondition Possible cause Suggested solutions Software Section. TryTurn on Print As Image from Select Download as Bit ImageAdvanced Options Solving print quality problems Characters ScatterMisformed SkewCondition Suggested solutions Curl Common Windows problemsCommon PostScript problems Option through Printer Settings Utility or PrinterCommon Linux problems Common Macintosh problemsInstalling a memory Dimm Installing accessoriesPrecautions when installing accessories Disconnect the power cordSelect Device Settings tab Installing a wireless network interface cardSetting the memory in the PostScript printer properties Select the Samsung ML-3470 Series printerConfiguring the wireless network parameters Configuring basic network settingsRestoring default values for wireless networking Selecting the authentication typeSetting Encryption Hexadecimal AlphanumericPrinter specifications SpecificationsPrinter specifications Specifications and DescriptionIndex Page Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Typical Installation Installing Printer SoftwareInstalling Software for Local Printing Select Typical installation for a local printer. Click NextCustom Installation Select Custom installation. Click Next Installing Software for Network Printing Custom Installation Installing Printer Software in Windows Reinstalling Printer Software Select the components you want to reinstall and click NextRemoving Printer Software NextPrinting a Document Select your printer driver from the Name drop-down listSelect Printers and Faxes Select your printer driver icon Printer SettingsPrinting to a file PRN Paper Orientation Layout TabPaper Tab Source Image ModeGraphics Tab Scaling PrintingWatermark Extras TabAdvanced Options OverlayAbout Tab Using a Favorite SettingUsing Help Printer TabAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing BookletsFitting Your Document to a Selected Paper Size Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document NoneCreating a Watermark Using WatermarksUsing an Existing Watermark Editing a WatermarkUsing a Page Overlay Using OverlaysWhat is an Overlay? Creating a New Page OverlayUsing Windows PostScript Driver AdvancedCheck the Share this printer box Setting Up a Host ComputerSetting Up a Client Computer Double-clickPrinters and FaxesUnderstanding Smart Panel Troubleshooting GuidePrinter Setting Toner LevelChanging the Smart Panel Program Settings Opening the Troubleshooting GuideUsing Printer Settings Utility Using Onscreen Help FileGetting Started Installing the Unified Linux DriverInstalling the Unified Linux Driver Uninstalling the Unified Linux Driver Click UninstallOpening the Unified Driver Configurator Using the Unified Driver ConfiguratorPrinters Configuration Double-clickUnified Driver Configurator on the desktopClasses Tab Configuring Printer PropertiesPorts Configuration Printing from Applications Printing FilesUninstalling the printer driver Installing SoftwareInstalling the printer driver Printer driverFor a USB-connected Setting Up the PrinterFor a Network-connected Mac OS 8.6 ~Printing a Document Changing Printer SettingsPrinting LayoutPaper Printer FeaturesGraphics Printing Multiple Pages on One Sheet of Paper Duplex PrintingIndex Macintosh 32 uninstall Rev.6.00
Top Page Image Contents