Samsung ML-3470D Selecting the authentication type, Setting Encryption, Hexadecimal Alphanumeric

Page 60

Selecting the authentication type

Authentication is a process of identifying the legitimacy of an user to access a network. You can select whether or not authentication is used.

1Press Menu until Network appears on the bottom line of the display and press OK.

2Press the scroll buttons until Wireless appears and press OK.

3Press the scroll buttons until WLAN Security appears and press OK.

4Press the scroll buttons until Static WEP appears and press OK.

5Press the scroll buttons until Authentication appears and press OK.

6Press the scroll buttons to select the type you want.

•Open System: Authentication is not used.

•Shared Key: Authentication is used.

7Press OK to save your selection.

8Press Stop to return to Standby mode.

Setting Encryption

If your network uses WEP encryption keys, you can must select the appropriate encryption type and configure encryption keys. You can configure up to four keys. The active key must match the key value and key position (for example, Key 1) configured on other wireless devices in the network.

1Press Menu until Network appears on the bottom line of the display and press OK.

2Press the scroll buttons until Wireless appears and press OK.

3Press the scroll buttons until WLAN Security appears and press OK.

4Press the scroll buttons until Static WEP appears and press OK.

5Press the scroll buttons until Encryption appears and press OK.

Note

If you have set the authentication type to Open System, the Encryption menu does not display.

6Set each encryption option and press OK.

•Encrypt. Type: Select an encryption type:

•Key Type: Select the key type of your network.

•Using Key: Select the key to be used in your network.

•Edit Key: Enter the key number for the selected key position. The numbers you can enter as follows:

 

Hexadecimal

Alphanumeric

 

 

 

64-bit WEP

10 digits

5 characters

 

 

 

 

Hexadecimal

Alphanumeric

 

 

 

128-bit WEP

26 digits

13 characters

 

 

 

7When you have finished, press Stop to return to Standby mode.

Restoring default values for wireless networking

If the problem occurrs when you use or set up the wireless network values, take following stops to restore factory default values. Generally, factory values of wireless networking are optimized for your printer.

1Press Menu until Network appears on the bottom line of the display and press OK.

2Press the scroll buttons until Wireless appears and press OK.

3Press the scroll buttons until WLAN Default appears and press OK.

4When Restore appears on the bottom line of the display, press OK. The printer starts restoring the default values.

10.4 <Installing accessories>

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Page Page Contact Samsung worldwide Slovakia Contents Ordering supplies and accessories MaintenanceTroubleshooting Installing accessoriesSafety and Regulatory Information Important Precautions and Safety InformationEnvironmental and Safety Consideration Laser Safety StatementOzone Safety Power SaverRecycling Radio Frequency EmissionsUnited States of America Declaration of Conformity European CountriesWireless Guidance Regulatory Compliance StatementsReplacing the Fitted Plug for UK Only Special features Special features Printer overview Finding more informationIntroduction Software SectionFeatures ML-3470D ML-3471ND Printer overviewFront view Rear view Control panel overviewML-3470D and ML-3471ND Understanding the Status LED Finding more informationAltitude adjustment Click Printer SettingSelecting a location Clearance spaceSystem setup Using control panel menusAccessing control panel menus Menu overviewInformation menu Layout menuSystem Setup menu Paper menuGraphic menu Emulation menu PostScriptUsing toner save mode Printing a demoChanging the display language Changing the font setting Contents Printer Settings Utility This program isSoftware overview Supplied softwarePrinter driver features FeatureSystem requirements WindowsLinux MacintoshRequirements Via network administration programs Supported operating systemsVia the control panel Configuring TCP/IP Using SetIP programDynamic addressing BOOTP/DHCP Static addressingConfiguring EtherTalk Setting Ethernet speedRestoring the network configuration Printing a network configurationLoading print media Selecting print mediaType Size Dimensions Weighta Capacityb Supported sizes of paperGuidelines for selecting and storing print media Guidelines for special print mediaMedia type Guidelines Loading paper Using the tray 1 or the optional tray Changing the size of the paper in the trayUsing the multi-purpose tray Load the paper with the side to be printed on facing upUsing manual feed mode Tips on using the multi-purpose traySelecting an output location Printing to the output tray Face downPrinting to the rear cover Face up Canceling a print job Printing a document Canceling a print jobBasic printing Printing a documentOrdering supplies and accessories AccessoriesHow to purchase Toner cartridgesMaintenance Cleaning the printerCleaning the outside of the printer Cleaning the inside of the printerMaintaining the toner cartridge Checking the remaining toner Redistributing toner cartridgeSaving Toner Toner Low appears on the displayReplacing the toner cartridge Toner Low Replace Toner appears on the displayMaintenance parts Clearing the Toner Low Replace Toner messageItems Yield Average Troubleshooting Clearing paper jamsPaper feed area TrayOptional tray Multi-purpose trayAround the toner cartridge Paper exit areaDuplex unit area Duplex jamTips for avoiding paper jams Troubleshooting checklist Understanding display messagesMessage Meaning Suggested solutions LSU Motor Error Open Heat ErrorOver Heat Error Self DiagnosticToner cartridge-related messages Solving general printing problems Condition Possible cause Suggested solutionsSelect Samsung ML-3470 Software Section. TrySelect Download as Bit Image Advanced OptionsTurn on Print As Image from Solving print quality problems Scatter MisformedCharacters SkewCommon Windows problems Common PostScript problemsCondition Suggested solutions Curl Option through Printer Settings Utility or PrinterCommon Linux problems Common Macintosh problemsInstalling accessories Precautions when installing accessoriesInstalling a memory Dimm Disconnect the power cordInstalling a wireless network interface card Setting the memory in the PostScript printer propertiesSelect Device Settings tab Select the Samsung ML-3470 Series printerConfiguring the wireless network parameters Configuring basic network settingsSelecting the authentication type Setting EncryptionRestoring default values for wireless networking Hexadecimal AlphanumericSpecifications Printer specificationsPrinter specifications Specifications and DescriptionIndex Page Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Installing Printer Software Installing Software for Local PrintingTypical Installation Select Typical installation for a local printer. Click NextCustom Installation Select Custom installation. Click Next Installing Software for Network Printing Custom Installation Installing Printer Software in Windows Reinstalling Printer Software Select the components you want to reinstall and click NextRemoving Printer Software NextPrinting a Document Select your printer driver from the Name drop-down listPrinter Settings Printing to a file PRNSelect Printers and Faxes Select your printer driver icon Layout Tab Paper TabPaper Orientation Image Mode Graphics TabSource Scaling PrintingExtras Tab Advanced OptionsWatermark OverlayUsing a Favorite Setting Using HelpAbout Tab Printer TabAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing BookletsPrinting on Both Sides of Paper Printing a Reduced or Enlarged DocumentFitting Your Document to a Selected Paper Size NoneUsing Watermarks Using an Existing WatermarkCreating a Watermark Editing a WatermarkUsing Overlays What is an Overlay?Using a Page Overlay Creating a New Page OverlayUsing Windows PostScript Driver AdvancedSetting Up a Host Computer Setting Up a Client ComputerCheck the Share this printer box Double-clickPrinters and FaxesTroubleshooting Guide Printer SettingUnderstanding Smart Panel Toner LevelOpening the Troubleshooting Guide Using Printer Settings UtilityChanging the Smart Panel Program Settings Using Onscreen Help FileInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Uninstalling the Unified Linux Driver Click UninstallUsing the Unified Driver Configurator Printers ConfigurationOpening the Unified Driver Configurator Double-clickUnified Driver Configurator on the desktopConfiguring Printer Properties Ports ConfigurationClasses Tab Printing from Applications Printing FilesInstalling Software Installing the printer driverUninstalling the printer driver Printer driverSetting Up the Printer For a Network-connectedFor a USB-connected Mac OS 8.6 ~Changing Printer Settings PrintingPrinting a Document LayoutPrinter Features GraphicsPaper Printing Multiple Pages on One Sheet of Paper Duplex PrintingIndex Macintosh 32 uninstall Rev.6.00
Top Page Image Contents