Samsung CLP-600 Clearing Paper Jams, Paper Feed Area, Message CLP Location GoTo, 600N only Jam

Page 46

Clearing Paper Jams

NOTE: When removing paper that is jammed in the printer, if possible always pull the paper in the direction that it normally moves so as not to damage internal components. Always pull firmly and evenly; do not jerk the paper. If the paper tears, ensure that all fragments of paper are removed; otherwise a jam will occur again.

When a paper jam occurs, a lamp turns on at the corresponding location on the Status map of the control panel. If you use the CLP-600N, the display on the control panel also tells you where the paper jam has occurred. Refer to the table below to locate the paper jam and to clear it:

	LED on	Message (CLP-	Location of	GoTo
	Status Map	600N only)	Jam	GoTo
	Status Map	600N only)	Jam
		Jam0 In Tray1	In the paper	page 7.4
			feed area
		Jam0 In MP Tray	In the multi-	page 7.5
			purpose tray
		Jam	Inside printer	page 7.6
		Inside Printer
		Jam	In the paper	page 7.7
		In Exit Area	exit area
		Jam0 In Tray2	In the optional	page 7.9
			Tray2

To resume printing after clearing paper jams, you must open and close the access door.

7.4

Solving Problems

In the Paper Feed Area

If paper is jammed in the paper feed area, a lamp turns on at the corresponding location on the Status map. If you use the CLP-600N, “Jam0 In Tray1” also appears on the display.

1Using the handle, completely open the access door.

2Carefully remove the paper by pulling in the direction as shown below. Go to step 6.

If you cannot find the jammed paper, or if there is any resistance removing the paper, stop pulling, and go to step 3.

CAUTION:

•Do not touch the green surface, the OPC drum, on the front of each toner cartridge with your hands or any other material. Use the handle on each cartridge in order to avoid touching this area.

•Be careful not to scratch the surface of the paper transfer belt.

•If you leave the access door open for more than a few minutes, the OPC drum can be exposed to light. This will cause damage to the OPC drum. Close the access door should the installation need to be halted for any reason.

Image 46

Contents Page Page Country Customer Care Center Web Site Contents Your printer’s embedded web page opens Configuring Network Parameters on the Control PanelReplacing Supplies Clearing Paper JamsImportant Precautions and Safety Information Recycling Regulatory Compliance Statements Replacing the Fitted Plug for UK Only Special Features IntroductionFront View Printer ComponentsRight Side View Printer software CD Setting Up Your PrinterUnpacking Components may differ from one country to anotherInstalling the Toner Cartridges Grip Load paper with the print side facing up Loading PaperSlide the tray back into the printer Changing the Size of the Paper in the Tray Connecting a Printer Cable For Local PrintingPrinting a Demo Using an Ethernet CableTurning the Printer On For Network Printing CLP-600NonlyChanging the Display Language Installing the Printer SoftwareSystem Requirements Win98SE Printer Driver FeaturesPrinter driver Feature First Watermark OverlayUnderstanding the Control Panel Using the Control PanelCancel button ButtonsButton Description Overview of Control Panel Menus Using Control Panel Menus CLPAccessing Control Panel Menus Information MenuColor Menu Setup MenuPrinter Menu Network Menu Configuration Print Net CFG Wlan DefaultFrame type Reset Network Netware ProtocolSizes and Capacities Using Print MaterialsChoosing Paper and Other Materials Guidelines for Paper and Special MaterialsUsing the Optional Tray Using Tray1Using the Multi-purpose Tray Using the Manual Feed Printing on Envelopes Printing on Special Print MaterialsLoad envelopes into the Multi-purpose Tray only Printing on Labels Printing on Preprinted PaperPrinting on Card Stock or Custom- sized Materials Basic Printing Canceling a Print JobPrinting a Document Canceling a Print Job Printing a DocumentIf you have an CLP-600 Printing a ConfigurationMaintaining Your Printer If you have an CLP-600NToner Cartridge Storage Replacing SuppliesManaging Toner Cartridges Toner Cartridge Life ExpectancyMaintaining Your Printer Replacing Toner Cartridges Replacing the Paper Transfer Belt Turn the printer on Replacing the Fuser Unit Cleaning the Inside of the Printer Cleaning the PrinterCleaning the Outside of the Printer Do not touch the green surface, the OPC drum, on the frontTo access SyncThru Web Service Start a web browser, such as Internet Explorer from WindowsStatus Response Solving ProblemsTroubleshooting Checklist Line/Continue buttonSolving General Printing Problems Problem Possible Cause SolutionTo Normal or Select Download as Bit ImageAdvanced Options window DraftMessage CLP Location GoTo Clearing Paper JamsPaper Feed Area 600N only JamMulti-purpose Tray Inside the Printer Paper Exit Area Solving Problems Optional Tray2 Open the outer jam cover in Tray2 Solving Problems Problem Solution Solving Print Quality ProblemsTips for Avoiding Paper Jams Toner smear Color or BlackBackground VerticalUnderstanding Display Messages Over Heat Error Fuser is abnormally Low Heat Error Fuser is abnormallyLow Persists, call for service Engine Fuser Printer Install Indicated colorLife span When the Replace Transfer Belt Soon Mode Ready Color CorrespondingPrint quality is not Optimal. When ‘Color Toner Empty’ Replace Tray1 Life span Contact a service Pick-rollerCommon Macintosh Problems Common Windows Problems Common Linux ProblemsProblem Possible Cause and Solution Using Cups N-up feature is achieved through postAm using BSD lpr Denied errorsConfiguring Network Parameters on the Control Panel Using Your Printer on a NetworkSetting Up a Network Connected Printer About Sharing the Printer on a NetworkConfiguring TCP/IP Printing a Network ConfigurationSetting Network Protocols Static AddressingConfiguring IPX Frame Types Dynamic Addressing BOOTP/DHCPPress the Upper Level button Configuring the Wireless Network Restoring the Network ConfigurationRebooting the Network Interface Card 13Press the On Line/Continue button to return to ready modeHexadecimal Alphanumeric Restoring the Wireless ConfigurationBit WEP Digits Characters 26digits Installing Printer Options Precautions When Installing Printer OptionsInstalling a Network Interface Interface Card PackageInstalling Printer Options Installing Printer Options Paper Specifications SpecificationsPrinter Specifications OverviewSupported Sizes of Paper Guidelines for Using Paper10.2 Paper Input Capacity Paper SpecificationsPaper Output Capacity Printer and Paper Storage EnvironmentEnvelopes LabelsIndex Inside 6.8 outside 6.8 componentsSoftware section Contents Sharing the Printer Locally For a USB-connected Macintosh Installing Software for Local Printing Installing Printer Software in WindowsInstalling Printer Software Typical InstallationCustom Installation Select Custom installation. Click Next Select the components to be installed and click NextInstalling Software for Network Printing Custom Installation Installing Printer Software in Windows Select the components you want to reinstall and click Next Reinstalling Printer SoftwareChanging the Software Language Removing Printer Software NextSelect your printer driver from the Name drop-down list Select Printers and Faxes Select your printer driver icon Printer SettingsLayout Tab OrientationPaper Tab SourceQuality Color ModeGraphics Tab Advanced OptionsAbout Tab Extras TabPrinter Tab Using a Favorite Setting Using HelpAdvanced Printing Printing Multiple Pages on One Sheet of Paper N-Up PrintingPrinting Posters Printing BookletsPrinting on Both Sides of Paper NonePrinting a Reduced or Enlarged Document Fitting Your Document to a Selected Paper SizeCreating a Watermark Using WatermarksUsing an Existing Watermark Click OK and start printingEditing a Watermark Using OverlaysWhat is an Overlay? Deleting a WatermarkUsing a Page Overlay If necessary, click Confirm Page Overlay When Deleting a Page OverlayList box Click Delete Overlay Sharing the Printer Locally Setting Up a Host ComputerSetting Up a Client Computer Check the Share this printer boxUnderstanding Smart Panel Using Smart PanelOpening the Troubleshooting Guide Toner LevelUsing Onscreen Help Using Printer Settings UtilityChanging the Smart Panel Program Settings You can view Printer Settings Utility help on screenSupported OS Using Your Printer in LinuxSystem Requirements Recommended CapacitiesInstalling the Printer Driver Changing the Printer Connection Method Uninstalling the Printer Driver Using the Configuration ToolSelect Complete uninstall and then click Uninstall Changing Llpr Properties Install the Printer driver Using Your Printer with a MacintoshInstalling Software for Macintosh Uninstalling the Printer driverFor a USB-connected Macintosh Setting Up the PrinterFor a Network-connected Macintosh Select Socket/HP Jet Direct in Printer TypePrinting Changing Printer SettingsLayout Setting Printing a DocumentPrinting Multiple Pages on One Sheet of Paper Printer Features SettingResolutionQuality Paper TypeLanguage, change 10 Layout properties, set Windows 15 toner save 15 true-type optionPage Rev .0

Related manuals

Manual 8 pages 19.01 Kb