Samsung 920WM z Please use Wall Mount according to the International standards, Click Windows

Page 18

zPlease use Wall Mount according to the International standards.

Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury.

Samsung is not liable for these kinds of accidents.

zSamsung is not liable for product damage or personal injury when a non-VESA or non- specified wall mount is used or the consumer fails to follow the product installation instructions.

zTo mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface.

zContact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified.

zPlease use Wall Mount according to the International standards.

Installing the Monitor Driver (Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown below.

zInternet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

1.Insert CD into the CD-ROM drive.

2.Click "Windows"

3.Choose your monitor model in the model list, then click the "OK" button.

4.If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. (Microsoft® Windows® XP/2000 Operating System)

This monitor driver is under certifying MS logo,and this installation

Image 18

Contents Install drivers SyncMaster 920WMPower NotationalDo not use the power cord when the connector or plug is dusty Insert the power plug firmly so that it does not come looseDo not disconnect the power cord while using the monitor Do not use a damaged or loose plugDo not place the product on an unstable or small surface area InstallationDo not drop the monitor when moving it Do not place the product on the floorInstalling a wall bracket must be done by a qualified professional CleanKeep any heating devices away from the power cable Put down the monitor carefullyDo not spray water or detergent directly onto the monitor Make sure to unplug the power cord before cleaning the productOthers Use the recommended detergent with a smooth clothDo not cover the vents on the monitor cabinet Keep the volume at a comfortable level when using the headphones Never insert anything metallic into the monitor openingsGood Postures When Using the Monitor Try to maintain a good posture when using the monitorconnected to other devices, are disconnected before moving the monitor Power Off, Screen Saver, or Power Save Mode WarrantyWhat is Image retention ? PRODUCT INFORMATION Image Retention FreeTo prevent this, the accumulated voltage difference must be decreased Please make sure the following items are included with your monitor Unpacking Without stand Monitor With stand Monitor & Simple StandManual Power Cord Warranty Card/ RegistrationQuick Setup Guide Users GuideRear Adjust buttons Enter button SOURCE buttonAUTO button AUTO Power button Power indicator 2 TextRGB IN port POWER portFor using a locking device, contact where you purchase it DVI IN HDCP portConnecting the Monitor RGB INDVI IN HDCP Using the Stand Monitor Assembly Attaching a BaseInstalling the Monitor Driver Automatic z Please use Wall Mount according to the International standards2. Click Windows Click Advanced Settings… Installing the Monitor Driver Manual3. Click Personalization and then Display Settings Microsoft Windows Vista Operating SystemThe certified driver will be posted on Samsung Monitor homepage Microsoft Windows XP Operating System 3. Click Display icon and choose the Settings tab then click Advanced 9. Click the Close button then click OK button continually Microsoft Windows 2000 Operating System How to install 1. Click Start , Setting , Control Panel1. Click Start , Setting , Control Panel Microsoft Windows Millennium Operating SystemLinux Operating System AUTO 4. AUTOWhen pressing the AUTO button after locking the OSD OSD Lock & UnlockAUTO Though the OSD adjustment lock function is activated, you can still When pressing the MENU button after locking the OSDOSD Lock & Unlock adjust the brightness and contrast, and adjust MagicBrightPush the MagicBright button to circle through available preconfigured VolumeMagicBright modesSOURCE SetupPicture PictureMENU→ → → , → MENU ColorBrightness Contrast MENU→ → , → → , → MENUCool Normal Warm ImageColor Tone Color Control Gamma Coarse FineH-Position Sharpness H-Position V-PositionLanguage V-PositionColor Reset SetupImage Reset InformationInformation Shows a video source, display mode on the OSD screenMENU → , → MENU Can you see Check Signal Cable on the screen? Connected using the D-sub cableCheck List Hz, a Not Optimum Control Panel → Display → Settings Q & ACheck the following items if there is trouble with the monitor Warning Messages Self-Test Feature CheckSelf-Test Feature Check EnvironmentUseful Tips z Judging the monitors working conditionGeneral PowerSaver Preset Timing Modes Table 1. Preset Timing ModesLatin America Contact SAMSUNG WORLDWIDENorth America EuropeAsia Pacific For Better Display ResolutionTerms Dot PitchAuthority Correct Disposal of This Product Waste Electrical & Electronic Equipment - Europe only