Samsung 920WM manual Q & A, Control Panel → Display → Settings

Page 38
Control Panel → Display → Settings.

There are only 16

Have the Windows colors been set

colors shown on the

properly?

screen.

 

The screen colors

 

have changed after

Has the video card been set

changing the video

card.

properly?

There is a message

Have you installed the monitor

that reads

driver?

"Unrecognized

See the video card manual to see if

monitor, Plug & Play

(VESA DDC) monitor

the Plug & Play (VESA DDC)

found".

function can be supported.

Problems related to

No sound

Audio

 

Sound level is too low.

product.)

Windows ME/2000/XP:

Set the colors properly at the

Control Panel → Display → Settings.

Set the video card by referring to the video card manual.

Install the monitor driver according to the Driver Installation Instructions.

Install the monitor driver according to the Driver Installation Instructions.

Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card.

(Refer to Connecting the Monitor)

Check the volume level.

Check the volume level.

If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.

Check the following items if there is trouble with the monitor.

1.Check if the power cord and the video cables are properly connected to the computer.

2.Check if the computer beeps more than 3 times when booting.

(If it does, request an after-service for the main board of the computer.)

3.If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver.

4.Check if the scanning ratio of the video screen is set at 56 Hz ~ 60 Hz. (Do not exceed 60 Hz when using the maximum resolution.)

5.If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel → System → Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.

If problems repeatedly occur, contact an authorized service center.

Q & A

Question

How can I change the frequency?

Answer

Frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)

How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel→Display→Settings.

* Contact the video card manufacturer for details.

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Install drivers SyncMaster 920WMPower NotationalDo not use the power cord when the connector or plug is dusty Insert the power plug firmly so that it does not come looseDo not disconnect the power cord while using the monitor Do not use a damaged or loose plugDo not place the product on an unstable or small surface area InstallationDo not drop the monitor when moving it Do not place the product on the floorInstalling a wall bracket must be done by a qualified professional CleanKeep any heating devices away from the power cable Put down the monitor carefullyDo not spray water or detergent directly onto the monitor Make sure to unplug the power cord before cleaning the productOthers Use the recommended detergent with a smooth clothDo not cover the vents on the monitor cabinet Keep the volume at a comfortable level when using the headphones Never insert anything metallic into the monitor openingsconnected to other devices, are disconnected before moving the monitor Good Postures When Using the MonitorTry to maintain a good posture when using the monitor Power Off, Screen Saver, or Power Save Mode WarrantyWhat is Image retention ? PRODUCT INFORMATION Image Retention FreeTo prevent this, the accumulated voltage difference must be decreased Manual Please make sure the following items are included with your monitorUnpacking Without stand Monitor With stand Monitor & Simple Stand Power Cord Warranty Card/ RegistrationQuick Setup Guide Users GuideRear Adjust buttons Enter button SOURCE buttonAUTO button AUTO Power button Power indicator 2 TextRGB IN port POWER portFor using a locking device, contact where you purchase it DVI IN HDCP portDVI IN HDCP Connecting the MonitorRGB IN Using the Stand Monitor Assembly Attaching a Base2. Click Windows Installing the Monitor Driver Automaticz Please use Wall Mount according to the International standards Click Advanced Settings… Installing the Monitor Driver Manual3. Click Personalization and then Display Settings Microsoft Windows Vista Operating SystemThe certified driver will be posted on Samsung Monitor homepage Microsoft Windows XP Operating System 3. Click Display icon and choose the Settings tab then click Advanced 9. Click the Close button then click OK button continually Microsoft Windows 2000 Operating System How to install 1. Click Start , Setting , Control Panel1. Click Start , Setting , Control Panel Microsoft Windows Millennium Operating SystemLinux Operating System AUTO 4. AUTOAUTO When pressing the AUTO button after locking the OSDOSD Lock & Unlock Though the OSD adjustment lock function is activated, you can still When pressing the MENU button after locking the OSDOSD Lock & Unlock adjust the brightness and contrast, and adjust MagicBrightPush the MagicBright button to circle through available preconfigured VolumeMagicBright modesSOURCE SetupPicture PictureMENU→ → → , → MENU ColorBrightness Contrast MENU→ → , → → , → MENUCool Normal Warm ImageColor Tone Color Control Gamma Coarse FineH-Position Sharpness H-Position V-PositionLanguage V-PositionColor Reset SetupImage Reset InformationMENU → , → MENU InformationShows a video source, display mode on the OSD screen Check List Can you see Check Signal Cable on the screen?Connected using the D-sub cable Hz, a Not Optimum Check the following items if there is trouble with the monitor Control Panel → Display → SettingsQ & A Warning Messages Self-Test Feature CheckSelf-Test Feature Check EnvironmentUseful Tips z Judging the monitors working conditionGeneral PowerSaver Preset Timing Modes Table 1. Preset Timing ModesLatin America Contact SAMSUNG WORLDWIDENorth America EuropeAsia Pacific For Better Display ResolutionTerms Dot PitchAuthority Correct Disposal of This Product Waste Electrical & Electronic Equipment - Europe only
Top Page Image Contents