Samsung 920WM manual Check List, Can you see Check Signal Cable on the screen?

Page 36

Check List

Check List

Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.

Symptom

No images on the screen. I cannot turn on the monitor.

Check List

Is the power cord connected properly?

Can you see "Check Signal Cable" on the screen?

If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.

Can you see "Not Optimum

Mode","Recommended Mode 1440 x 900 60Hz" on the screen?

Solutions

Check the power cord connection and supply.

(Connected using the D-sub cable)

Check the signal cable connection.

(Connected using the DVI cable) If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press button to have the monitor double-check the input signal source.

If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card.

(Refer to the Preset Timing Modes)

Note: If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.

You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly.

Adjust the maximum resolution and frequency that the monitor can handle properly.

If the display exceeds SXGA or 75

Image 36

Contents Install drivers SyncMaster 920WMPower NotationalInsert the power plug firmly so that it does not come loose Do not disconnect the power cord while using the monitorDo not use the power cord when the connector or plug is dusty Do not use a damaged or loose plugInstallation Do not drop the monitor when moving itDo not place the product on an unstable or small surface area Do not place the product on the floorClean Keep any heating devices away from the power cableInstalling a wall bracket must be done by a qualified professional Put down the monitor carefullyMake sure to unplug the power cord before cleaning the product OthersDo not spray water or detergent directly onto the monitor Use the recommended detergent with a smooth clothDo not cover the vents on the monitor cabinet Keep the volume at a comfortable level when using the headphones Never insert anything metallic into the monitor openingsGood Postures When Using the Monitor Try to maintain a good posture when using the monitorconnected to other devices, are disconnected before moving the monitor Warranty What is Image retention ?Power Off, Screen Saver, or Power Save Mode PRODUCT INFORMATION Image Retention FreeTo prevent this, the accumulated voltage difference must be decreased Please make sure the following items are included with your monitor Unpacking Without stand Monitor With stand Monitor & Simple StandManual Warranty Card/ Registration Quick Setup GuidePower Cord Users GuideAdjust buttons Enter button SOURCE button AUTO button AUTO Power button Power indicatorRear 2 TextPOWER port For using a locking device, contact where you purchase itRGB IN port DVI IN HDCP portConnecting the Monitor RGB INDVI IN HDCP Using the Stand Monitor Assembly Attaching a BaseInstalling the Monitor Driver Automatic z Please use Wall Mount according to the International standards2. Click Windows Installing the Monitor Driver Manual 3. Click Personalization and then Display SettingsClick Advanced Settings… Microsoft Windows Vista Operating SystemThe certified driver will be posted on Samsung Monitor homepage Microsoft Windows XP Operating System 3. Click Display icon and choose the Settings tab then click Advanced 9. Click the Close button then click OK button continually How to install 1. Click Start , Setting , Control Panel 1. Click Start , Setting , Control PanelMicrosoft Windows 2000 Operating System Microsoft Windows Millennium Operating SystemLinux Operating System AUTO 4. AUTOWhen pressing the AUTO button after locking the OSD OSD Lock & UnlockAUTO When pressing the MENU button after locking the OSD OSD Lock & UnlockThough the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust MagicBrightVolume MagicBrightPush the MagicBright button to circle through available preconfigured modesSetup PictureSOURCE PictureColor Brightness ContrastMENU→ → → , → MENU MENU→ → , → → , → MENUImage Color Tone Color Control GammaCool Normal Warm Coarse FineSharpness H-Position V-Position LanguageH-Position V-PositionSetup Image ResetColor Reset InformationInformation Shows a video source, display mode on the OSD screenMENU → , → MENU Can you see Check Signal Cable on the screen? Connected using the D-sub cableCheck List Hz, a Not Optimum Control Panel → Display → Settings Q & ACheck the following items if there is trouble with the monitor Self-Test Feature Check Self-Test Feature CheckWarning Messages EnvironmentUseful Tips z Judging the monitors working conditionGeneral PowerSaver Preset Timing Modes Table 1. Preset Timing ModesContact SAMSUNG WORLDWIDE North AmericaLatin America EuropeAsia Pacific Resolution TermsFor Better Display Dot PitchAuthority Correct Disposal of This Product Waste Electrical & Electronic Equipment - Europe only