Samsung SCX-4100 specifications Precautions, Safety Warning

Page 3

Precautions

11. Precautions

In order to prevent accidents and to prevent damage to the equipment please read the precautions listed below carefully before servicing the printer and follow them closely.

1.1 Safety Warning

(1)Only to be serviced by appropriately qualified service engineers.

High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably trained and qualified service engineer.

(2)Use only Samsung replacement parts

There are no user serviceable parts inside the printer. Do not make any unauthorized changes or

additions to the printer, these could cause the printer to malfunction and create electric shock or fire haz-ards.

(3)Laser Safety Statement

The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class 1(1) laser products, and elsewhere, it is certified as a Class I laser product

con-forming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.

Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The reflected beam, although invisible, can damage your eyes. When using this product, these basic safety pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.

CAUTION - INVISIBLE LASER RADIATION

WHEN THIS COVER OPEN.

DO NOT OPEN THIS COVER.

VORSICHT - UNSICHTBARE LASERSTRAHLUNG,

WENN ABDECKUNG GE FFNET.

NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RAYONNEMENT LASER INVISIBLE EN CAS

D OUVERTURE. EXPOSITION DANGEREUSE

AU FAISCEAU.

ATTENZIONE - RADIAZIONE LASER INVISIBILE IN CASO DI

APERTURA. EVITARE L ESPOSIZIONE AL

FASCIO.

PRECAUCION - RADIACION LASER IVISIBLE CUANDO SE ABRE.

EVITAR EXPONERSE AL RAYO.

ADVARSEL. - USYNLIG LASERSTR LNING VED BNING, N R

SIKKERHEDSBRYDERE ER UDE AF FUNKTION.

UNDG UDSAETTELSE FOR STR LNING.

ADVARSEL. - USYNLIG LASERSTR LNING N R DEKSEL

PNES. STIRR IKKE INN I STR LEN.

UNNG EKSPONERING FOR STR LEN.

VARNING - OSYNLIG LASERSTR LNING N R DENNA DEL

RPPNAD OCH SP RREN R URKOPPLAD. BETRAKTA EJ STR LEN. STR LEN R FARLIG.

VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA N KYM TT M LLE LASER-

S TEILYLLE L KATSO S TEESEEN.

Service Manual

1-1

Image 3
Contents Block Diagram PrecautionsSpecifications TroubleshootingHttp//itself.sec.samsung.co.kr Safety Warning PrecautionsToxic material Electric Shock and Fire Safety PrecautionsAssembly / Disassembly Precautions Handling PrecautionsDisregarding this warning may cause bodily injury Be careful with the high temperature partESD Precautions Tool for Troubleshooting Acronyms and Abbreviations IPC Select a location for the printer 1 A4 5% Pattern Sample Pattern for the Test2 A4 2% Pattern 3 A4 IDC 5% Patten Memo General Specifications SpecificationsScan Specification Print SpecificationCopy Copy SpecificationPaper Handiling Specification Whql Other SpecificationMemo Front View Printer ComponentsRear View Control Panel System Layout Fixing PartFuser Paper Feed MechanismTransfer Ass’y Drive Ass’yCIS Driver Circuit Safety Relevant FactsScanner Unit Scan Image ControllerLSU Laser Scanner Unit Toner Cartridge Main PBA Sensor input circuit Asic Chorus2Flash Memory SdramDC FAN / Solenoid Driver Paper Feeding, Toner Cartridge SensingPaper Exit Sensing Cover Open SensingSmps & Hvps HVPSHigh Voltage Power Supply Length of Power Cord 1830 ± 50mm Power Switch Fitted Smps Switching Mode Power SupplyRated Power Output Consumption PowerSafty Requrement Fuser AC Power ControlFeature Environment ConditionFeeding Engine F/WDrive TransferFusing 5 LSUHeat Lamp Method Memo General Precautions on Disassembly Releasing Plastic LatchesWhenever servicing the machine, you must perform as follows Front and Rear Cover Units Side Covers Remove Scanner Ass’y Scanner Ass’yDismantle Scanner Ass’y Spring Pulley Idle ETC Belt Middle Cover FuserHeat Lamp Type Remove 4 screws and divide the Fuser into two parts LSU Exit RollerFan Engine Shield Ass’y Smps Transfer Roller Feed Roller Remove the Feed Roller and Feed Roller1, as shown below Pick Up Roller & Solenoid Memo To enter the Engine Test mode Engine Test ModeTo enter the Engine Test Mode DiagnosticPaper Path Paper Tray Clearing Paper JamsPaper Exit Area Manual Feeder Fuser Area or Around the Toner CartridgePrinting the System Data List Clearing the MemoryClearing the Drum LCD Status Display by Each Error Consumables and Replacement PartsRoller Defective image Typical defect Periodic Defective ImagePrinting Problems Causes and Solutions Vertical Black Lines and BandsVertical White Line Black/White Spot Horizontal Black BandsDark Image or a Black Light ImageBackground Uneven DensityGhost Digital Printer Ghost Stains on the FaceBlank Page Print out Stains on BackCopy Problems White CopyBlack Copy Defective Image Quality Abnormal noisePaper Feed problems Causes and Solutions Wrong Print Position2 JAM 4 JAM 3 JAMPaper rolled in the fuser Multi-FeedingPaper rolled on the OPC Drum Printer Faults Causes and Solutions Fuser ErrorLSU Error Paper Empty Fuser gear melts due to overheating causing Paper JamCover Open Paper Empty without indicationNo error message when the cover is open Defective motor operation No PowerPrinted Vertical Lines become curved Standard of guarantee for consumable parts Toner Cartridge ServicePrecautions on Safe-keeping of Toner Cartridge Service for the Life of Toner CartridgeEnded Signs and Measures of Poor toner cartridgeFault Signs Cause & Check Solution Fault Signs Cause & Check Solution Ghost & Image Printer is not working Software Problems Causes and SolutionsNot working with the message insufficient printer Abnormal Printing How to delete the data in the spool manager Spool ErrorMemo Exploded Views and Parts List Main Assembly Main Assembly Parts List Frame Assembly Description SEC.Code ’ty Remark Frame Unit Assembly Parts ListFrame Unit Assembly Parts ListCont Scanner Unit Assembly Scanner Unit Assembly Parts List Fuser Unit Assembly Fuser Unit Assembly Parts List WASHER-PLAIN Middle Cover Unit Assembly ’ty Remark Middle Cover Unit Assembly Parts ListDrive Unit Assembly Parts List Drive Unit AssemblyCassette Unit Assembly Cassette Unit Assembly Parts List Block Diagram 10.10Connection Diagram
Related manuals
Manual 169 pages 2.29 Kb Manual 167 pages 32.6 Kb