Samsung SCX-4100 Consumables and Replacement Parts, LCD Status Display by Each Error

Page 64

Alignment & Adjustments

6.7 Consumables and Replacement Parts

The cycle period outlined below is a general guideline for maintenance.

The example list is for an average usage of 50 transmitted and received documents per day. Environmental conditions and actual use will vary these factors.

The cycle period given below is for reference only.

COMPONENT

REPLACEMENT CYCLE

Pick-up Roller

60,000 Pages

 

 

 

 

Paepr Feeding Roller(Friction Pad)

60,000 Pages

 

 

 

 

Transfer Roller

60,000 Pages

 

 

 

 

Fuser

60,000 Pages

 

 

 

 

Toner Cartridge

Original 1,000 Pages

Replacement 3,000 Pages

 

 

 

6.8 The LCD Status Display by Each Error

LCD

Meaning

Solutions

Door Open

The front or rear cover is not securely

Close the cover until it locks into place.

 

latched.

 

 

 

 

[JAM 1] or

The toner cartrige is not installed.

Install the toner cartridge.

[No Cartridge]

 

 

 

 

 

Low Heat Error

There is a problem in the fuser unit.

Unplug the power cord and plug it back in.

Open Heat Error

 

(Tech Mode Reference)

 

 

[Over Heat]

 

 

 

 

 

[LSU Error]

A problem has occurred in the LSU

Unplug the power cord and plug it back in.

 

(Laser Scanning Unit).

(Tech Mode Reference)

 

 

 

No Paper

The paper tray has run out of paper.

Load paper in the paper tray.

[Add Paper]

 

 

 

 

 

Paper Jam 0

Paper has jammed in the feeding area of

Clear the jam.

Open/Close Door

the paper tray.

 

 

 

 

Paper Jam 1

• Paper has jammed in the fuser area.

• Clear the jam.

Open/Close Door

• A paper jam has occurred in the manual

• Clear the jam.

 

 

feeder or the machine detects non-

 

 

feeding from the manual feeder.

 

 

 

 

Paper Jam 2

Paper has jammed in the paper exit area.

Clear the jam.

Check Inside

 

 

 

 

 

Service Manual

Samsung Electronics

6-7

Image 64
Contents Precautions SpecificationsTroubleshooting Block DiagramHttp//itself.sec.samsung.co.kr Precautions Safety WarningElectric Shock and Fire Safety Precautions Toxic materialHandling Precautions Assembly / Disassembly PrecautionsBe careful with the high temperature part Disregarding this warning may cause bodily injuryESD Precautions Tool for Troubleshooting Acronyms and Abbreviations IPC Select a location for the printer Sample Pattern for the Test 1 A4 5% Pattern2 A4 2% Pattern 3 A4 IDC 5% Patten Memo Specifications General SpecificationsPrint Specification Scan SpecificationCopy Specification CopyPaper Handiling Specification Other Specification WhqlMemo Printer Components Front ViewRear View Control Panel System Layout Paper Feed Mechanism Transfer Ass’yDrive Ass’y Fixing PartFuserSafety Relevant Facts Scanner UnitScan Image Controller CIS Driver CircuitLSU Laser Scanner Unit Toner Cartridge Main PBA Asic Chorus2 Flash MemorySdram Sensor input circuitPaper Feeding, Toner Cartridge Sensing Paper Exit SensingCover Open Sensing DC FAN / Solenoid DriverSmps & Hvps HVPSHigh Voltage Power Supply Smps Switching Mode Power Supply Rated Power OutputConsumption Power Length of Power Cord 1830 ± 50mm Power Switch FittedFuser AC Power Control FeatureEnvironment Condition Safty RequrementEngine F/W DriveTransfer Feeding5 LSU FusingHeat Lamp Method Memo Releasing Plastic Latches General Precautions on DisassemblyWhenever servicing the machine, you must perform as follows Front and Rear Cover Units Side Covers Scanner Ass’y Remove Scanner Ass’yDismantle Scanner Ass’y Spring Pulley Idle ETC Belt Middle Cover FuserHeat Lamp Type Remove 4 screws and divide the Fuser into two parts Exit Roller LSUFan Engine Shield Ass’y Smps Transfer Roller Feed Roller Remove the Feed Roller and Feed Roller1, as shown below Pick Up Roller & Solenoid Memo Engine Test Mode To enter the Engine Test ModeDiagnostic To enter the Engine Test modePaper Path Clearing Paper Jams Paper TrayPaper Exit Area Fuser Area or Around the Toner Cartridge Manual FeederClearing the Memory Printing the System Data ListClearing the Drum Consumables and Replacement Parts LCD Status Display by Each ErrorPeriodic Defective Image Roller Defective image Typical defectVertical Black Lines and Bands Printing Problems Causes and SolutionsVertical White Line Horizontal Black Bands Black/White SpotLight Image Dark Image or a BlackUneven Density BackgroundGhost Stains on the Face Digital Printer GhostStains on Back Blank Page Print outWhite Copy Copy ProblemsBlack Copy Abnormal noise Defective Image QualityWrong Print Position Paper Feed problems Causes and Solutions2 JAM 3 JAM 4 JAMMulti-Feeding Paper rolled in the fuserPaper rolled on the OPC Drum Fuser Error Printer Faults Causes and SolutionsLSU Error Fuser gear melts due to overheating causing Paper Jam Paper EmptyPaper Empty without indication Cover OpenNo error message when the cover is open No Power Defective motor operationPrinted Vertical Lines become curved Toner Cartridge Service Precautions on Safe-keeping of Toner CartridgeService for the Life of Toner Cartridge Standard of guarantee for consumable partsSigns and Measures of Poor toner cartridge EndedFault Signs Cause & Check Solution Fault Signs Cause & Check Solution Ghost & Image Software Problems Causes and Solutions Printer is not workingNot working with the message insufficient printer Abnormal Printing Spool Error How to delete the data in the spool managerMemo Exploded Views and Parts List Main Assembly Main Assembly Parts List Frame Assembly Frame Unit Assembly Parts List Description SEC.Code ’ty RemarkFrame Unit Assembly Parts ListCont Scanner Unit Assembly Scanner Unit Assembly Parts List Fuser Unit Assembly Fuser Unit Assembly Parts List WASHER-PLAIN Middle Cover Unit Assembly Middle Cover Unit Assembly Parts List ’ty RemarkDrive Unit Assembly Drive Unit Assembly Parts ListCassette Unit Assembly Cassette Unit Assembly Parts List Block Diagram 10.10Connection Diagram
Related manuals
Manual 169 pages 2.29 Kb Manual 167 pages 32.6 Kb